Council Regulation (EU) 2023/2890of 19 December 2023amending Regulation (EU) 2021/2278 suspending the Common Customs Tariff duties referred to in Article 56(2), point (c), of Regulation (EU) No 952/2013 on certain agricultural and industrial products

Council Regulation (EU) 2023/2890 of 19 December 2023 amending Regulation (EU) 2021/2278 suspending the Common Customs Tariff duties referred to in Article 56(2), point (c), of Regulation (EU) No 952/2013 on certain agricultural and industrial products THE COUNCIL OF THE EUROPEAN UNION, Having regard to the Treaty on the Functioning of the European Union, and in particular Article 31 thereof, Having regard to the proposal from the European Commission, Whereas: (1) In order to ensure a sufficient and uninterrupted supply of certain agricultural and industrial products which are not produced in the Union and thereby avoid any disturbances on the market for those products, Common Customs Tariff duties of the type referred to in Article 56(2), point (c), of Regulation (EU) No 952/2013 of the European Parliament and of the Council Regulation (EU) No 952/2013 of the European Parliament and of the Council of 9 October 2013 laying down the Union Customs Code (OJ L 269, 10.10.2013, p. 1). (CCT duties) on those products have been suspended by Council Regulation (EU) 2021/2278 Council Regulation (EU) 2021/2278 of 20 December 2021 suspending the Common Customs Tariff duties referred to in Article 56(2), point (c), of Regulation (EU) No 952/2013 on certain agricultural and industrial products, and repealing Regulation (EU) No 1387/2013 (OJ L 466, 29.12.2021, p. 1). . As a result, the products listed in the Annex to Regulation (EU) 2021/2278 can be imported into the Union at reduced or zero duty rates without any limitation as regards their quantity. (2) The Union production of certain products that are not listed in the Annex to Regulation (EU) 2021/2278 is inadequate to meet the specific requirements of the user industries in the Union. As it is in the Union’s interest to ensure an adequate supply of certain products, and having regard to the fact that identical, equivalent or substitute products are not produced in sufficient quantities within the Union, it is necessary to grant a complete suspension of the CCT duties also on those products. (3) With a view to promoting integrated battery production in the Union, a partial suspension of the CCT duties should be granted in respect of certain products related to battery production that are currently not listed in the Annex to Regulation (EU) 2021/2278, and the respective Union production of which is inadequate to meet the specific requirements of the user industries in the Union. The date for the mandatory review of those suspensions should be 31 December 2024, in order for that review to take into account the short-term evolution of the battery production sector in the Union. (4) It is necessary to amend the product description and classification for certain CCT duty suspensions listed in the Annex to Regulation (EU) 2021/2278 in order to take into account technical product developments and economic trends in the market. (5) The Commission has reviewed certain CCT duty suspensions listed in the Annex to Regulation (EU) 2021/2278 in accordance with Article 2 of that Regulation. For those CCT duty suspensions, new dates should therefore be set for their next mandatory review.

(6) It is no longer in the interest of the Union to maintain the suspension of CCT duties for certain products listed in the Annex to Regulation (EU) 2021/2278. The suspensions for those products should therefore be deleted with effect from 1 January 2024. (7) Regulation (EU) 2021/2278 should therefore be amended accordingly. (8) In order to avoid any interruption in the application of the autonomous tariff suspension scheme and to comply with the guidelines set out in the communication from the Commission of 13 December 2011 concerning autonomous tariff suspensions and quotas, the changes provided for in this Regulation regarding the tariff suspensions for the products concerned should apply from 1 January 2024. This Regulation should therefore enter into force as a matter of urgency, HAS ADOPTED THIS REGULATION:

Article 1

The Annex to Regulation (EU) 2021/2278 is replaced by the text set out in the Annex to this Regulation.

Article 2

This Regulation shall enter into force on the day following that of its publication in the Official Journal of the European Union. It shall apply from 1 January 2024. This Regulation shall be binding in its entirety and directly applicable in all Member States. Done at Brussels, 19 December 2023. For the Council The President T. Ribera Rodríguez

Annex

ANNEX .

Annex

ANNEX Suspension of duties is subject to end-use customs supervision in accordance with Article 254 of Regulation (EU) No 952/2013. However, the suspension of tariff duties does not apply where the processing is carried out by retail or catering undertakings. Only the ad valorem duty is suspended. The specific duty shall continue to apply. A surveillance of imports of goods covered by this tariff suspension shall be established in accordance with the procedure laid down in Articles 55 and 56 of Commission Implementing Regulation (EU) 2015/2447 of 24 November 2015 laying down detailed rules for implementing certain provisions of Regulation (EU) No 952/2013 of the European Parliament and of the Council laying down the Union Customs Code (OJ L 343, 29.12.2015, p. 558). CUS (Customs Union and Statistics Number) is assigned to each ECICS record (product). ECICS (European Customs Inventory of Chemical Substances) is an information tool managed by the European Commission, General Directorate for Taxation and Customs Union. More information can be found via the following link: http://ec.europa.eu/taxation_customs/common/databases/ecics/index_en.htm. A measure introduced or amended by Council Regulation (EU) 2023/2890 of 19 December 2023 amending Regulation (EU) 2021/2278 suspending the Common Customs Tariff duties referred to in Article 56(2), point (c), of Regulation (EU) No 952/2013 on certain agricultural and industrial products (OJ, L, 2023/2890, 29.12.2023, ELI: http://data.europa.eu/eli/reg/2023/2890/oj).Where more than one CN code is listed as falling within the scope of the measure, the asterisk concerns the entire measure. Serial NumberCN codeTARICDescriptionRate of autonomous dutySupplementary UnitDate envisaged for mandatory review0.6748ex0709530010Fresh or chilled chanterelles for treatment other than simple repacking for retail sale0 %-31.12.20250.3349ex0710809550Bamboo shoots, frozen, not put up for retail sale0 %-31.12.20240.2829ex0711590011Mushrooms, excluding mushrooms of the genera Agaricus, Calocybe, Clitocybe, Lepista, Leucoagaricus, Leucopaxillus, Lyophyllum and Tricholoma, provisionally preserved in brine, in sulphur water, or in other preservative solutions, but unsuitable in that state for immediate consumption, for the food-canning industry0 %-31.12.20260.2463

ex07123200 ex07123300 ex07123400 ex07123900 10 10 31 31 Mushrooms, excluding mushrooms of the genus Agaricus, dried, whole or in identifiable slices or pieces, for treatment other than simple repacking for retail sale0 %-31.12.20240.3347ex0804100030Dates, fresh or dried, for use in the manufacture (excluding packing) of products of drink or food industries0 %-31.12.20240.3228ex0811909520Boysenberries, frozen, not containing added sugar, not put up for retail sale0 %-31.12.20240.2409ex0811909530Pineapple (Ananas comosus), in pieces, frozen0 %-31.12.20240.2408ex0811909540Rose-hips, uncooked or cooked by steaming or boiling in water, frozen, not containing added sugar or other sweetening matter0 %-31.12.20240.2864 ex15119019 ex15119091 ex15131110 ex15131930 ex15132110 ex15132930 20 20 20 20 20 20 Palm oil, coconut (copra) oil, palm kernel oil, for the manufacture of: industrial monocarboxylic fatty acids of subheading 38231910, methyl esters of fatty acids of heading 2915 or 2916, fatty alcohols of subheadings 290517, 290519 and 382370 used for the manufacture of cosmetics, washing products or pharmaceutical products, fatty alcohols of subheading 290516, pure or mixed, used for the manufacture of cosmetics, washing products or pharmaceutical products, stearic acid of subheading 38231100, goods of heading 3401, or fatty acids with high purity of heading 2915 0 %-31.12.2024 0.8443ex1515609910Microbial oil, refined or semi-refined, containing by weight 35 % or more but not more than 70 % of arachidonic acid or 35 % or more but not more than 50 % of docosahexaenoic acid0 %-31.12.20240.3341ex1515909992Vegetable oil, refined or semi-refined, containing by weight 35 % or more but not more than 57 % of arachidonic acid or 35 % or more but not more than 50 % of docosahexaenoic acid0 %-31.12.20240.768615162010Hydrogenated castor oil, so called opal-wax0 %-31.12.20240.4708ex1516209620Jojoba oil, hydrogenated and interesterified, without any further chemical modification and not subjected to any texturisation process0 %-31.12.20240.4080ex1517909910Vegetable oil, refined, containing by weight 25 % or more but not more than 50 % arachidonic acid or 12 % or more but not more than 65 % docosahexaenoic acid and standardized with high oleic sunflower oil (HOSO)0 %-31.12.20260.8569ex1517909920 An edible mixture of animal and vegetable oils consisting of 99 % or more by weight of fish oil exclusively from the species Pacific pollock (Gadus chalcogrammus): containing by weight 90 % or more of triglycerides, with 50 % or more by weight of its fatty acids being omega-3 fatty acids, containing by weight 0,15 % or more but not more than 0,25 % of tocopherols and vegetable oils, in immediate packing in steel drums of more than 180 kg/net but not more than 200 kg/net, for use in the manufacture of fish oil-based omega-3 supplements in the form of soft gel capsules 0 %-31.12.20250.6182 ex19019099 ex21069098 39 45 Preparation in powder form containing by weight: 15 % or more but not more than 35 % of wheat derived Maltodextrin,

15 % or more but not more than 35 % of whey (milk serum), 10 % or more but not more than 30 % of refined, bleached, deodorised and non-hydrogenated sunflower oil, 10 % or more but not more than 30 % of blended, aged spray dried cheese, 5 % or more but not more than 15 % of buttermilk and 0,1 % or more but not more than 10 % of sodium caseinate, disodium phosphate, lactic acid 0 %-31.12.2024 0.2423ex1902301040Glass noodles containing 60 % or more by weight of mung bean starch in immediate packings of 5 kg or more and not put up for retail sale0 %-31.12.20240.2866ex2005910010Bamboo shoots, prepared or preserved, in immediate packings of a net content of more than 5 kg0 %-31.12.20240.5884 ex20079950 ex20079950 ex20079993 83 93 10 Mango puree concentrate, obtained by cooking: of the genus Mangifera spp., with a sugar content by weight of not more than 30 % for use in the manufacture of products of food and drink industry 6 %-31.12.20240.5875 ex20079950 ex20079950 84 94 Papaya puree concentrate, obtained by cooking: of the genus Carica spp., with a sugar content by weight of more than 13 % but not more than 30 % for use in the manufacture of products of food and drink industry 7,8 %-31.12.20240.5867 ex20079950 ex20079950 85 95 Guava puree concentrate, obtained by cooking: of the genus Psidium spp., with a sugar content by weight of more than 13 % but not more than 30 % for use in the manufacture of products of food and drink industry 6 %-31.12.20240.4716ex2008939120Sweetened dried cranberries, excluding packing alone as processing, for the manufacture of products of food processing industries0 %-31.12.20270.5004ex2008994894 Mango puree: not from concentrate, of the genus Mangifera, of a Brix value of 14 or more, but not more than 20, used in the manufacture of products of drink industry 6 %-31.12.20240.4709 ex20089949 ex20089999 30 40 Seedless boysenberry puree not containing added spirit, whether or not containing added sugar0 %-31.12.2025 0.5587 ex20089949 ex20089999 70 11 Blanched vine leaves of the genus Karakishmish, in brine, containing by weight: more than 6 % of salt concentration, 0,1 % or more but not more than 1,4 % of acidity expressed as citric acid monohydrate and whether or not but not more than 2000 mg/kg of sodium benzoate according CODEX STAN 192-1995 for use in the manufacture of stuffed vine leaves with rice 0 %-31.12.20270.6723ex2008999120Chinese water chestnuts (Eleocharis dulcis or Eleocharis tuberosa) peeled, washed, blanched, chilled and individually quick-frozen for use in the manufacture of products of food industry for treatment other than simple repacking0 %-31.12.20250.7767ex2008999935 Frozen pulp from acai berries: hydrated and pasteurised, separated from the kernels by the addition of water, with a Brix value of less than 6, and with a sugar content of less than 5,6 % 0 %-31.12.20240.4992 ex20094192 ex20094199 20 70 Pineapple juice: not from concentrate, of the genus Ananas, of a Brix value of 11 or more but not more than 16,

used in the manufacture of products of drink industry 8 %-31.12.20250.4664ex2009493091 Pineapple juice, other than in powder form: with a Brix value of more than 20 but not more than 67, a value of more than € 30 per 100 kg net weight, containing added sugar used in the manufacture of products of food or drink industry 0 %-31.12.20240.4623ex2009813110 Cranberry juice concentrate: of a Brix value of 40 or more but not more than 66, in immediate packings of a content of 50 litres or more 0 %l31.12.2024 0.6356 ex20098973 ex20098973 11 13 Passion fruit juice and passion fruit juice concentrate, whether or not frozen: with a Brix value of 13,7 or more but not more than 55, of a value of more than € 30 per 100 kg net weight, in immediate packings of a content of 50 litres or more, and with added sugar for the use in the manufacture of products of food or drink industry 0 %l31.12.20240.4159ex2009897920Frozen boysenberry juice concentrate with a Brix value of 61 or more, but not more than 67, in immediate packings of a content of 50 litres or more0 %l31.12.20240.6050ex2009897930 Frozen acerola juice concentrate: with a Brix value of more than 48 but not more than 67, in immediate packings of a content of 50 litres or more 0 %l31.12.20240.5206ex2009897985 Acai berry juice concentrate: of the species Euterpe oleracea, frozen, not sweetened, not in powder form, of a Brix value of 23 or more but not more than 32, in immediate packings of a content of 10 kg or more 0 %-31.12.20260.6365 ex20098997 ex20098997 21 29 Passion fruit juice and passion fruit juice concentrate, whether or not frozen: with a Brix value of 10 or more but not more than 13,7, of a value of more than € 30 per 100 kg net weight, in immediate packings of a content of 50 litres or more, and without added sugar for the use in the manufacture of products of food or drink industry 0 %l31.12.20240.4157ex2009899996 Coconut water unfermented, not containing added spirit or sugar, and in immediate packing of a content of 20 litres or more 0 %l31.12.2026 0.6152ex2106102020Soya protein concentrate having a protein content by weight, calculated on a dry weight basis, of 65 % or more but not more than 90 % in powder or textured form0 %-31.12.20240.3340ex2106102030Preparation on the base of soya protein isolate, containing by weight 6,6 % or more but not more than 8,6 % of calcium phosphate0 %-31.12.20240.7284 ex21069092 ex35040090 50 10 Casein protein hydrolysate consisting of: by weight 20 % or more but not more than 70 % free amino acids, and peptones of which by weight more than 90 % having a molecular weight of not more than 2000 Da 0 %-31.12.20270.5246ex2519901010Fused magnesia with a purity by weight of 94 % or more0 %-31.12.20260.6330 ex27075000 ex27079980 20 10 Mixture of xylenol-isomers and ethyl phenol-isomers, with a total xylenol content by weight of 62 % or more but less than 95 %0 %-31.12.20240.6168ex2707999910Heavy and medium oils, whose aromatic content exceeds their non-aromatic content, for use as refinery feedstock to undergo one of the specific processes described in Additional note 5 to Chapter 270 %-31.12.20240.8144ex2710122520

Mixture of C6 aliphatic hydrocarbons (CAS RN 92112-69-1), containing by weight 60 % or more but not more than 80 % of n-hexane (CAS RN 110-54-3), with: a specific gravity of 0,666 or more but not more than 0,686, a total of carbonyl compounds of less than 1 ppm, a total of acetylenic compounds of less than 2 ppm 0 %-31.12.20250.7823 ex27101981 ex27101999 30 50 Catalytically hydroisomerized and dewaxed base oil of hydrogenated, highly isoparaffinic hydrocarbons, containing: 90 % or more by weight of saturates, and not more than 0,03 % by weight of sulphur, and with a viscosity index of 80 or more, but less than 120, and a a kinematic viscosity less than 5,0 cSt at 100°C or more than 13,0 cSt at 100°C 0 %-31.12.2024 0.7822 ex27101981 ex27101999 40 60 Catalytically hydroisomerized and dewaxed base oil of hydrogenated, highly isoparaffinic hydrocarbons, containing: 90 % or more by weight of saturates, and not more than 0,03 % by weight of sulphur, with a viscosity index of 120 or more 0 %-31.12.20240.6495ex2710199920 Catalytic de-waxed base oil, synthesised from gaseous hydrocarbons, followed by a heavy paraffin conversion process (HPC), containing: not more than 1 mg/kg of sulphur more than 99 % by weight of saturated hydrocarbons more than 75 % by weight of n- and iso-paraffinic hydrocarbons with a carbon chain length of 18 or more but not more than 50; and a kinematic viscosity at 40 °C of more than 6,5 mm2/s, or a kinematic viscosity at 40 °C of more than 11 mm2/s with a viscosity index of 120 or more 0 %-31.12.20240.7393ex2712909910Blend of 1-alkenes containing by weight 90 % or more 1-alkenes of a chain length of 24 carbon atoms or more but not more than 1 % 1-alkenes of a chain length of more than 70 carbon atoms0 %-31.12.20270.4531ex2804509040Tellurium (CAS RN 13494-80-9) of a purity by weight of 99,99 % or more, but not more than 99,999 %, based on metallic impurities measured by ICP analysis0 %-31.12.20240.802128047010Red phosphorus0 %-31.12.20270.802228047090Phosphorus, other than red phosphorus0 %-31.12.20240.6658ex2805120010Calcium with a purity of 98 % or more by weight, in powder or wire form (CAS RN 7440-70-2)0 %-31.12.20250.5609ex2805199020Lithium metal (CAS RN 7439-93-2) of a purity by weight of 98,8 % or more0 %-31.12.20270.2559ex2805301010Alloy of cerium and other rare-earth metals, containing by weight 47 % or more of cerium0 %-31.12.2024 0.4979 28053021 28053029 28053031 28053039 28053040 Rare-earth metals, scandium and yttrium, of a purity by weight of 95 % or more0 %-31.12.20250.7769ex2809200010Aqueous solution of phosphoric acid (CAS RN 7664-38-2), containing by weight 85 % or more phosphoric acid0 %-31.12.20240.2407ex2811220010Silicon dioxide (CAS RN 7631-86-9) in the form of powder, for use in the manufacture of high performance liquid chromatography columns (HPLC) and sample preparation cartridges0 %-31.12.20240.6836ex2811220015 Amorphous silicon dioxide (CAS RN 60676-86-0) in the form of powder of a purity by weight of 99,0 % or more

with a median grain size of 0,7 µm or more, but not more than 2,1 µm where 70 % of the particles have a diameter of not more than 3 µm 0 %-31.12.20240.7292ex2811299010Tellurium dioxide (CAS RN 7446-07-3)0 %-31.12.20270.3308ex2812900010Nitrogen trifluoride (CAS RN 7783-54-2)0 %-31.12.20240.5747ex2816400010Barium hydroxide (CAS RN 17194-00-2)0 %-31.12.20270.7594ex2818101110Sol-Gel corundum (CAS RN 1302-74-5) with an aluminium oxide content of 99,6 % or more by weight, having a micro crystalline structure in the form of rods with an aspect ratio of 1,3 or more, but not more than 6,00 %-31.12.2024 0.5110ex2818109120 Sintered corundum with a micro crystalline structure, consisting of aluminium oxide (CAS RN 1344-28-1), magnesium aluminate (CAS RN 12068-51-8) and the rare earth aluminates of yttrium, lanthanum, and neodymium, with a content by weight (calculated as oxides) of: 94 % or more, but less than 98,5 % of aluminium oxide, 2 % (± 1,5 %) of magnesium oxide, 1 % (± 0,6 %) of yttrium oxide, and either 2 % (± 1,2 %) of lanthanum oxide, or 2 % (± 1,2 %) of lanthanum oxide and neodymium oxide, with less than 50 % of the total weight having a particle size of more than 10 mm 0 %-31.12.20250.8425ex2818109130 Sintered corundum with a micro crystalline structure, consisting of aluminium oxide (CAS RN 1344-28-1) and magnesium aluminate (CAS RN 12068-51-8), with a content by weight (calculated as oxides) of: 92 % or more, but not more than 94 % of aluminium oxide, and 7 % (± 1 %) of magnesium oxide 0 %-31.12.20270.4640ex2818200010Activated alumina with a specific surface area of at least 350 m2/g0 %-31.12.20240.6837ex2818300020 Aluminium hydroxide (CAS RN 21645-51-2) in the form of powder, with a purity by weight of 99,5 % or more, with a decomposition point of 263°C or more, with a particle size of 4 µm (± 1 µm), with a Total-Na2O-content by weight of not more than 0,06 % 0 %-31.12.20250.3306ex2818300030Aluminium hydroxide oxide in the form of boehmite or pseudoboehmite (CAS RN 1318-23-6)0 %-31.12.20240.5369ex2819909010Dichromium trioxide (CAS RN 1308-38-9) for use in metallurgy0 %-31.12.20260.5752ex2823000010 Titanium dioxide (CAS RN 13463-67-7): of a purity by weight of 99,9 % or more, with an average grain-size of 0,7 µm or more but not more than 2,1 µm 0 %-31.12.2027 0.5576ex2825100010Hydroxylammonium chloride (CAS RN 5470-11-1)0 %-31.12.20270.7897ex2825200010Lithium hydroxide monohydrate (CAS RN 1310-66-3)2,6 %-31.12.20240.380028253000Vanadium oxides and hydroxides0 %-31.12.20260.3303ex2825500020Copper (I or II) oxide containing by weight 78 % or more of copper and not more than 0,03 % of chloride0 %-31.12.20240.6819ex2825500030Copper (II) oxide (CAS RN 1317-38-0), with a particle size of not more than 100 nm0 %-31.12.20250.5555ex2825600010Zirconium dioxide (CAS RN 1314-23-4)0 %-31.12.20270.7193ex2825700020Molybdic Acid (CAS RN 7782-91-4)0 %-31.12.20260.5055ex2826199010Tungsten hexafluoride (CAS RN 7783-82-6) with a purity by weight of 99,9 % or more0 %-31.12.20250.8296ex2826908030Lithium hexafluorophosphate (CAS RN 21324-40-3) with a purity by weight of 99 % or more2,7 %-31.12.20240.2865ex2827398510Copper monochloride (CAS RN 7758-89-6) of a purity by weight of 96 % or more but not more than 99 %0 %-31.12.20240.4180ex2827398520Antimony pentachloride (CAS RN 7647-18-9) of a purity by weight of 99 % or more0 %-31.12.20260.6143ex2827398540Barium chloride dihydrate (CAS RN 10326-27-9)0 %-31.12.20240.4423ex2827499010Hydrated zirconium dichloride oxide (CAS RN 7699-43-6)0 %-31.12.20240.6463ex2827600010Sodium iodide (CAS RN 7681-82-5)0 %-31.12.20240.7596ex2828100010Calcium hypochlorite (CAS RN 7778-54-3) having an active chlorine content of 65 % or more0 %-31.12.20240.3302ex2830100010Disodium tetrasulphide (CAS RN 12034-39-8), containing by weight 38 % or less of sodium calculated on the dry weight0 %-31.12.20240.3859ex2833298020Manganese sulphate monohydrate (CAS RN 10034-96-5)0 %-31.12.20240.4338ex2835100010Sodium hypophosphite monohydrate (CAS RN 10039-56-2)0 %-31.12.2027

0.6144ex2835100020Sodium hypophosphite (CAS RN 7681-53-0)0 %-31.12.20240.7452ex2835100030Aluminium Phosphinate (CAS RN 7784-22-7)0 %-31.12.20240.8448ex2835100040Calcium phosphinate (CAS RN 7789-79-9) with a purity by weight of 98 % or more0 %-31.12.20270.2524ex2836910020 Lithium carbonate, containing one or more of the following impurities at the concentrations indicated: 2 mg/kg or more of arsenic, 200 mg/kg or more of calcium, 200 mg/kg or more of chlorides, 20 mg/kg or more of iron, 150 mg/kg or more of magnesium, 20 mg/kg or more of heavy metals, 300 mg/kg or more of potassium, 300 mg/kg or more of sodium, 200 mg/kg or more of sulphates, determined according to the methods specified in the European Pharmacopœia 0 %-31.12.20240.2863ex2836991730Zirconium (IV) basic carbonate (CAS RN 57219-64-4 or 37356-18-6) with a purity by weight of 96 % or more0 %-31.12.20240.3300ex2837190020Copper cyanide (CAS RN 544-92-3)0 %-31.12.20240.4078ex2837200010Tetrasodium hexacyanoferrate (II) (CAS RN 13601-19-9)0 %-31.12.20260.2861ex2839900020Calcium silicate (CAS RN 1344-95-2)0 %-31.12.20240.6632ex2840209010Zinc borate (CAS RN 12767-90-7)0 %-31.12.20250.8520ex2840209020Barium borate (CAS RN 13701-59-2) with a purity by weight of 99 % or more0 %-31.12.20270.7288ex2841500011Potassium dichromate (CAS RN 7778-50-9) with a purity by weight of 99 % or more, for use as intermediate for the production of chrome2 %-31.12.20250.6142ex2841700010Diammonium tetraoxomolybdate(2-) (CAS RN 13106-76-8)0 %-31.12.20240.6482ex2841700030Hexaammonium heptamolybdate, anhydrous (CAS RN 12027-67-7) or as tetrahydrate (CAS RN 12054-85-2)0 %-31.12.2024 0.4323ex2841800010Diammonium wolframate (ammonium paratungstate) (CAS RN 11120-25-5)0 %-31.12.20270.8441ex2841800020 Disodium tungstate (CAS RN 13472-45-2) with a: purity by weight of 99 % or more, chlorine content of less than 100 ppm 0 %-31.12.20270.7301ex2841903010Potassium metavanadate (CAS RN 13769-43-2)0 %-31.12.20270.5936ex2841908520Potassium titanium oxide (CAS RN 12056-51-8) in powder form with a purity of 99 % or more0 %-31.12.20240.4416ex2842100010Synthetic beta zeolite powder0 %-31.12.20240.4588ex2842100020Synthetic chabasite zeolite powder0 %-31.12.20240.7397ex2842100050Fluorphlogopite (CAS RN 12003-38-2)0 %-31.12.20270.7097ex2842100060 Aluminosilicate (CAS RN 1318-02-1) with a purity by weight of 94 % or more, a zeolite structure of aluminophosphate-eighteen (AEI), and a phase purity of 90 % or more for use in the manufacture of copper zeolite 0 %-31.12.20260.4642ex2842901010Sodium selenate (CAS RN 13410-01-0)0 %-31.12.20240.329528451000Heavy water (deuterium oxide) (Euratom) (CAS RN 7789-20-0)0 %-31.12.20240.418928454000Helium-3 (CAS RN 14762-55-1)0 %-31.12.20260.329728459010Deuterium and compounds thereof; hydrogen and compounds thereof, enriched in deuterium; mixtures and solutions containing these products (Euratom)0 %-31.12.20240.8237ex28459010104-(Tert-Butyl)-2-(2-(methyl-d3)propan-2-yl-1,1,1,3,3,3-d6)phenol (CAS RN 2342594-40-3) with a purity by weight of 98 % or more0 %-31.12.20260.4191ex2845909020Water enriched at a level of 95 % or more by weight with oxygen-18 (CAS RN 14314-42-2)0 %-31.12.20240.4190ex2845909030(13C)Carbon monoxide (CAS RN 1641-69-6)0 %-31.12.2026

0.8426ex2845909050Ytterbium oxide (CAS RN 1380743-42-9), with a purity by weight of 99 % or more, enriched to 99,0 % or more but not more than 99,8 % of Ytterbium-1760 %-31.12.20270.2859 ex28461000 ex38249996 10 53 Rare-earth concentrate containing by weight 60 % or more but not more than 95 % of rare-earth oxides and not more than 1 % each of zirconium oxide, aluminium oxide or iron oxide, and having a loss on ignition of 5 % or more by weight0 %-31.12.20240.3296ex2846100020Dicerium tricarbonate (CAS RN 537-01-9), whether or not hydrated0 %-31.12.20240.3420ex2846100030Cerium lanthanum carbonate, whether or not hydrated0 %-31.12.20240.3227 28469030 28469040 28469050 28469060 28469070 28469090 Compounds, inorganic or organic, of rare-earth metals, of yttrium or of scandium or of mixtures of these metals, other than those of subheading 284610000 %-31.12.20240.3418ex2850002010Silane (CAS RN 7803-62-5)0 %-31.12.20240.5497ex2850002040Germanium tetrahydride (CAS RN 7782-65-2)0 %-31.12.20260.7302ex2850002060Disilane (CAS RN 1590-87-0)0 %-31.12.20270.7555ex2850002070Cubic Boron nitride (CAS RN 10043-11-5)0 %-31.12.20240.3419ex2850002080Arsine (CAS RN 7784-42-1) with a purity by volume of 99,999 % or more0 %-31.12.20240.4492ex2850006010Sodium azide (CAS RN 26628-22-8)0 %-31.12.20240.3421ex2853909020Phosphine (CAS RN 7803-51-2)0 %-31.12.20240.8282ex29031900201,3-Dichloropropane (CAS RN 142-28-9) with a purity by weight of 99 % or more0 %-31.12.20260.663329034200Difluoromethane (CAS RN 75-10-5)0 %-31.12.2025 0.6007ex2903440010Pentafluoroethane (CAS RN 354-33-6)0 %-31.12.20240.3674ex2903450030 1,1,1,2-Tetrafluoroethane (CAS RN 811-97-2) conforming to the following specifications: not more than 600 ppm by weight of HFC-134 (1,1,2,2-tetrafluoroethane), not more than 5 ppm by weight of HFC-143a (1,1,1-trifluoroethane), not more than 2 ppm by weight of HFC-125 (pentafluoroethane), not more than 100 ppm by weight of HCFC-124 (1-chloro-1,2,2,2- tetrafluoroethane), not more than 30 ppm by weight of CFC-114 (1,2-dichlorotetrafluoroethane), not more than 50 ppm by weight of CFC-114a (1,1-dichlorotetrafluoroethane), not more than 250 ppm by weight of HCFC-133a (1-chloro-2,2,2-trifluoroethane), not more than 2 ppm by weight of HCFC-22 (chlorodifluoromethane), not more than 2 ppm by weight of CFC-115 (chloropentafluoroethane), not more than 2 ppm by weight of CFC-12 (dichlorodifluoromethane), not more than 20 ppm by weight of HCC-40 (methyl chloride), not more than 20 ppm by weight of HFC-245cb (1,1,1,2,2-pentafluoropropane), not more than 20 ppm by weight of H-12B1 (chlorodifluorobromomethane), not more than 20 ppm by weight of HFC-32 (difluoromethane), not more than 15 ppm by weight of HCFC-31 (chlorofluoromethane), not more than 10 ppm by weight of HFC-152a (1,1-difluoroethane), not more than 20 ppm by weight of HFO-1131 (1-chloro-2-fluoroethylene), not more than 20 ppm by weight of HCFO-1122 (1-chloro–2,2-difluoroethylene), not more than 3 ppm by weight of HFO-1234yf (2,3,3,3-tetrafluoropropene),

not more than 3 ppm by weight of HFO-1243zf (3,3,3-trifluoropropene), not more than 3 ppm by weight of HCFO-1122a (1-chloro–1,2-difluoroethylene), not more than 4,5 ppm by weight of HFO-1234yf + HCFO-1122a + HFO-1243zf (2,3,3,3-tetrafluoropropene + 1-chloro–1,2-difluoroethylene + 3,3,3-trifluoropropene), not more than 3 ppm by weight of any individual unspecified/unknown chemical, not more than 10 ppm by weight of all unspecified/unknown chemicals combined, not more than 10 ppm by weight of water, with an acidity level of not more than 0,1 ppm by weight, without halides, not more than 0,01 % by volume of high boilers, without any odour (no malodour), for use with or without further purification as an under GMP (Good Manufacturing Practice) produced inhalation grade of HFC-134a in the manufacture of a propellant for medical aerosols whose contents are absorbed in the oral or nasal cavities, and/or the respiratory tract 0 %-31.12.2024 0.2542ex29034700201,1,1,3,3-Pentafluoropropane (HFC-245fa) (CAS RN 460-73-1)0 %-31.12.20240.2854ex2903493010Carbon tetrafluoride (tetrafluoromethane) (CAS RN 75-73-0)0 %-31.12.20240.2852ex2903493020Perfluoroethane (CAS RN 76-16-4)0 %-31.12.20240.6077ex29034930301H-Perfluorohexane (CAS RN 355-37-3)0 %-31.12.20240.5803ex29035100102,3,3,3-Tetrafluoroprop-1-ene (2,3,3,3-tetrafluoropropene) (CAS RN 754-12-1)0 %-31.12.20270.4517ex2903510020Trans-1,3,3,3-tetrafluoroprop-1-ene (Trans-1,3,3,3-tetrafluoropropene) (CAS RN 29118-24-9)0 %-31.12.20240.6076ex2903590020(Perfluorobutyl) ethylene (CAS RN 19430-93-4)0 %-31.12.20240.4066ex2903590030Hexafluoropropene (CAS RN 116-15-4)0 %-31.12.20260.7324ex29035900401,1,2,3,4,4-Hexafluorobuta-1,3-diene (CAS RN 685-63-2)0 %-31.12.20270.8553ex2903691925(E)-1,4-Dibrombut-2-ene (CAS RN 821-06-7) with a purity by weight of 98 % or more0 %-31.12.2028 0.8525ex29036919352,2-Dibromopropane (CAS RN 594-16-1) with a purity by weight of 99 % or more0 %-31.12.20280.7974ex29036919403-(Bromomethyl)pentane (CAS RN 3814-34-4) with a purity by weight of 99 % or more0 %-31.12.20250.8318ex2903691950Vinyl bromide (CAS RN 593-60-2) with a purity by weight of 98 % or more, or as a solution in tetrahydrofuran (CAS RN 109-99-9) containing by weight 23 % or more, but not more than 26 % vinylbromide0 %-31.12.20270.8151ex29036919601-Bromo-2-methylpropane (CAS RN 78-77-3) with a purity by weight of 99 % or more0 %-31.12.20260.7895ex2903720010Dichloro-1,1,1-trifluoroethane (CAS RN 306-83-2) with a purity by weight of 99 % or more0 %-31.12.20240.3675ex29037760101,1,1-Trichlorotrifluoroethane (CAS RN 354-58-5)0 %-31.12.20240.5212ex2903779010Chlorotrifluoroethylene (CAS RN 79-38-9)0 %-31.12.20260.7513ex2903780010Octafluoro-1,4-diiodobutane (CAS RN 375-50-8)0 %-31.12.20240.7755ex2903780020Trifluoroiodomethane (CAS RN 2314-97-8)0 %-31.12.20240.6485ex2903793010Trans-1-chloro-3,3,3-trifluoropropene (CAS RN 102687-65-0)0 %-31.12.20240.7826ex29037930301-Bromo-5-chloropentane (CAS RN 54512-75-3) with a purity by weight of 99 % or more0 %-31.12.20240.5765ex2903898050Chlorocyclopentane (CAS RN 930-28-9)0 %-31.12.20270.7304ex2903898060Octafluorocyclobutane (CAS RN 115-25-3)0 %-31.12.20270.6611ex29039980154-Bromo-2-chloro-1-fluorobenzene (CAS RN 60811-21-4)0 %-31.12.20250.8492ex29039980181-Fluoronaphthalene (CAS RN 321-38-0) with a purity by weight of 99 % or more0 %-31.12.20270.3410ex29039980201,2-Bis(pentabromophenyl)ethane (CAS RN 84852-53-9)0 %-31.12.20240.8557ex29039980233,5-Bis(trifluoromethyl) benzylbromide (CAS RN 32247-96-4) with a purity by weight of 95 % or more0 %-31.12.2028

0.8017ex29039980252,2’-Dibromobiphenyl (CAS RN 13029-09-9) with a purity by weight of 95 % or more0 %-31.12.20250.8018ex29039980352-Bromo-9,9’-spirobi[9H-fluoren] (CAS RN 171408-76-7) with a purity by weight of 95 % or more0 %-31.12.20250.3411ex2903998040 2,6-Dichlorotoluene (CAS RN 118-69-4), of a purity by weight of 99 % or more and containing: 0,001 mg/kg or less of tetrachlorodibenzodioxines, 0,001 mg/kg or less of tetrachlorodibenzofurans, 0,2 mg/kg or less of tetrachlorobiphenyls 0 %-31.12.20240.8076ex29039980451-Bromo-4-(trans-4-propylcyclohexyl)benzene (CAS RN 86579-53-5) with a purity by weight of 95 % or more0 %-31.12.20250.4529ex2903998050Fluorobenzene (CAS RN 462-06-6)0 %-31.12.20240.8101ex29039980551-Bromo-4-(trans-4-ethylcyclohexyl)benzene (CAS RN 91538-82-8) with a purity by weight of 95 % or more0 %-31.12.20250.8166ex29039980652,6-Difluorobenzyl bromide (CAS RN 85118-00-9) with a purity by weight of 97 % or more0 %-31.12.20260.8177ex29039980701-[Chloro(phenyl)methyl]-2-methylbenzene (CAS RN 41870-52-4) with a purity by weight of 99 % or more0 %-31.12.20260.6235ex29039980753-Chloro-alpha,alpha,alpha-trifluorotoluene (CAS RN 98-15-7)0 %-31.12.20240.5917ex29039980801-Bromo-3,4,5-trifluorobenzene (CAS RN 138526-69-9)0 %-31.12.20240.3407ex2904100030Sodium p-styrenesulphonate (CAS RN 2695-37-6)0 %-31.12.20240.4686ex2904100050Sodium 2-methylprop-2-ene-1-sulphonate (CAS RN 1561-92-8)0 %-31.12.20240.3409ex2904200010Nitromethane (CAS RN 75-52-5)0 %-31.12.20250.3391ex2904200020Nitroethane (CAS RN 79-24-3)0 %-31.12.20270.3408ex29042000301-Nitropropane (CAS RN 108-03-2)0 %-31.12.20250.3390ex29042000402-Nitropropane (CAS RN 79-46-9)0 %-31.12.20240.2526ex29049900201-Chloro-2,4-dinitrobenzene (CAS RN 97-00-7)0 %-31.12.2024 0.6612ex2904990025Difluoromethanesulphonyl chloride (CAS RN 1512-30-7)0 %-31.12.20250.3388ex2904990030Tosyl chloride (CAS RN 98-59-9)0 %-31.12.20240.6613ex29049900351-Fluoro-4-nitrobenzene (CAS RN 350-46-9)0 %-31.12.20250.5745ex29049900404-Chlorobenzenesulphonyl chloride (CAS RN 98-60-2)0 %-31.12.20270.7507ex29049900452-Nitrobenzenesulfonyl Chloride (CAS RN 1694-92-4)0 %-31.12.20240.6001ex2904990050Ethanesulphonyl chloride (CAS RN 594-44-5)0 %-31.12.20240.7957ex29049900552,4-Dichloro-1,3-dinitro-5-(trifluoromethyl)benzene (CAS RN 29091-09-6) with a purity by weight of 96 % or more0 %-31.12.20250.6407ex29049900604,4’-Dinitrostilbene–2,2’-disulfonic acid (CAS RN 128-42-7)0 %-31.12.20240.8160ex29049900654-Nitrotoluene-2-sulphonic acid (CAS RN 121-03-9) in powder form, with a purity by weight of 80 % or more and a content of water by weight of 15 % or more0 %-31.12.20260.6270ex29049900701-Chloro-4-nitrobenzene (CAS RN 100-00-5)0 %-31.12.20240.6560ex29049900801-Chloro-2-nitrobenzene (CAS RN 88-73-3)0 %-31.12.20240.6186ex2905110010Methanol (CAS RN 67-56-1) with a purity of 99,85 % by weight or more0 %-31.12.20240.2967ex2905190011Potassium tert-butanolate (CAS RN 865-47-4), whether or not in the form of a solution in tetrahydrofuran according to note 1e) to Chapter 29 of the CN0 %-31.12.20240.6118ex2905190020Butyltitanate monohydrate, homopolymer (CAS RN 162303-51-7)0 %-31.12.20240.6119ex2905190025Tetra-(2-ethylhexyl) titanate (CAS RN 1070-10-6)0 %-31.12.20240.3384ex29051900302,6-Dimethylheptan-4-ol (CAS RN 108-82-7)0 %-31.12.20240.4793ex29051900402,6-Dimethylheptan-2-ol (CAS RN 13254-34-7)0 %-31.12.20240.5534ex2905190070Titanium tetrabutanolate (CAS RN 5593-70-4)0 %-31.12.20270.5533ex2905190080Titanium tetraisopropoxide (CAS RN 546-68-9)0 %-31.12.2027

0.6002ex2905190085Titanium tetraethanolate (CAS RN 3087-36-3)0 %-31.12.20240.6464ex2905220010Linalool (CAS RN 78-70-6) containing by weight 90,7 % or more of (3R)-(-)-Linalool (CAS RN 126-91-0)0 %-31.12.20240.7114ex29052200203,7-Dimethyloct-6-en-1-ol (CAS RN 106-22-9)0 %-31.12.20260.7388ex2905299010Cis-hex-3-en-1-ol (CAS RN 928-96-1)0 %-31.12.20270.7674ex2905320020(2S)-Propane-1,2-diol (CAS RN 4254-15-3) with a purity by weight of 98 % or more0 %-31.12.20240.8544ex29053995152,5-Dimethylhexane-2,5-diol (CAS RN 110-03-2) with a purity by weight of 98 % or more0 %-31.12.20280.5255ex29053995302,4,7,9-Tetramethyl-4,7-decanediol (CAS RN 17913-76-7)0 %-31.12.20260.5847ex2905399540Decane-1,10-diol (CAS RN 112-47-0)0 %-31.12.20270.5908ex29053995502-Methyl-2-propylpropane-1,3-diol (CAS RN 78-26-2)0 %-31.12.20240.7701ex2905399560Dodecane-1,12-diol (CAS RN 5675-51-4)0 %-31.12.20240.7914ex29053995702-Methylpropane-1,3-diol (CAS RN 2163-42-0) with a purity by weight of 98 % or more0 %-31.12.20240.8370ex2905399580Pentane-1,5-diol (CAS RN 111-29-5) with a purity by weight of 97 % or more0 %-31.12.20270.4624ex29055998202,2,2-Trifluoroethanol (CAS RN 75-89-8)0 %-31.12.20240.3378ex2906190010Cyclohex-1,4-ylenedimethanol (CAS RN 105-08-8)0 %-31.12.20240.3380ex29061900204,4’-Isopropylidenedicyclohexanol (CAS RN 80-04-6)0 %-31.12.20240.6257ex29061900504-tert-Butylcyclohexanol (CAS RN 98-52-2)0 %-31.12.20240.8231ex29061900605-Methyl-2-(prop-1-en-2-yl)cyclohexanol, mixture of isomers (CAS RN 7786-67-6) with a purity by weight of 90 % or more0 %-31.12.20260.3681ex29062900201-Hydroxymethyl-4-methyl-2,3,5,6-tetrafluorobenzene (CAS RN 79538-03-7)0 %-31.12.20240.7373ex29062900502,2’-(m-Phenylene)dipropan-2-ol (CAS RN 1999-85-5)0 %-31.12.2027 0.7806ex29062900603-[3-(Trifluoromethyl)phenyl]propan-1-ol (CAS RN 78573-45-2)0 %-31.12.20240.7963ex29062900701,2,3,4-Tetrahydro-1-naphthol (CAS RN 529-33-9) with a purity by weight of 95 % or more0 %-31.12.20250.6757ex29062900802-Bromo-5-iodo-benzenemethanol (CAS RN 946525-30-0) with a purity by weight of 98 % or more0 %-31.12.20240.5855ex29062900852-Phenylethanol (CAS RN 60-12-8) with a purity by weight of 95 % or more0 %-31.12.20270.6329ex2907120020Mixture of meta-cresol (CAS RN 108-39-4) and para-cresol (CAS RN 106-44-5) with a purity by weight of 99 % or more0 %-31.12.20240.6559ex2907120030p-Cresol (CAS RN 106-44-5)0 %-31.12.20240.5216ex29071590102-Naphthol (CAS RN 135-19-3)0 %-31.12.20260.6256ex29071910102,6-Xylenol (CAS RN 576-26-1)0 %-31.12.20240.4480ex2907199020Biphenyl-4-ol (CAS RN 92-69-3)0 %-31.12.20240.7753ex29071990302-Methyl-5-(propan-2-yl)phenol (CAS RN 499-75-2)0 %-31.12.20240.3372ex2907210010Resorcinol (CAS RN 108-46-3)0 %-31.12.20240.8482ex29072900134,4’-Methylenedi–2,6-xylenol (CAS RN 5384-21-4) with a purity by weight of 98,5 % or more0 %-31.12.20270.6026ex29072900156,6’-Di-tert-butyl–4,4’-butylidenedi-m-cresol (CAS RN 85-60-9)0 %-31.12.20240.3369ex29072900204,4’-(3,3,5-Trimethylcyclohexylidene)diphenol (CAS RN 129188-99-4)0 %-31.12.20240.6454ex29072900254-Hydroxybenzyl alcohol (CAS RN 623-05-2)0 %-31.12.20240.3367ex29072900304,4’,4”-Ethylidynetriphenol (CAS RN 27955-94-8)0 %-31.12.20240.5432ex29072900452-Methylhydroquinone (CAS RN 95-71-6)0 %-31.12.20260.3368ex29072900506,6’,6”-Tricyclohexyl–4,4’,4”-butane-1,1,3-triyltri(m-cresol) (CAS RN 111850-25-0)0 %-31.12.20240.6558ex29072900652,2’-Methylenebis(6-cyclohexyl-p-cresol) (CAS RN 4066-02-8)0 %-31.12.2024

0.2584ex29072900702,2’,2”,6,6’,6”-Hexa-tert-butyl-α,α’,α”-(mesitylene-2,4,6-triyl)tri-p-cresol (CAS RN 1709-70-2)0 %-31.12.20240.7402ex2907290075Biphenyl-4,4’-diol (CAS RN 92-88-6)0 %-31.12.20240.3848ex2907290085Phloroglucinol whether or not hydrated0 %-31.12.20240.5903ex2908190010Pentafluorophenol (CAS RN 771-61-9)0 %-31.12.20240.5914ex29081900204,4’-(Perfluoroisopropylidene)diphenol (CAS RN 1478-61-1)0 %-31.12.20240.6260ex29081900304-Chlorophenol (CAS RN 106-48-9)0 %-31.12.20240.6782ex29081900403,4,5-Trifluorophenol (CAS RN 99627-05-1)0 %-31.12.20250.6915ex29081900504-Fluorophenol (CAS RN 371-41-5)0 %-31.12.20250.7720ex29081900602,2’,6,6’-Tetrabromo–4,4’-isopropylidenediphenol (CAS RN 79-94-7)0 %-31.12.20240.8204ex29081900702,3,6-Trifluorophenol (CAS RN 113798-74-6) with a purity by weight of 98 % or more0 %-31.12.20260.3361ex2909199020Bis(2-chloroethyl) ether (CAS RN 111-44-4)0 %-31.12.20240.3359ex2909199030Mixture of isomers of nonafluorobutyl methyl ether or nonafluorobutyl ethyl ether, of a purity by weight of 99 % or more0 %-31.12.20240.4035ex29091990503-Ethoxy-perfluoro-2-methylhexane (CAS RN 297730-93-9)0 %-31.12.20260.5407ex29092000108-Methoxycedrane (CAS RN 19870-74-7)0 %-31.12.20260.5503ex29093038201,1’-Propane–2,2-diylbis[3,5-dibromo-4-(2,3-dibromopropoxy)benzene] (CAS RN 21850-44-2)0 %-31.12.20260.6649ex29093038301,1’-(1-Methylethylidene)bis[3,5-dibromo-4-(2,3-dibromo-2-methylpropoxy)]-benzene (CAS RN 97416-84-7)0 %-31.12.20250.7454ex29093038404-Benzyloxybromobenzene (CAS RN 6793-92-6)0 %-31.12.20240.7828ex29093038502-(1-Adamantyl)-4-Bromoanisole (CAS RN 104224-63-7) with a purity by weight of 99 % or more0 %-31.12.20240.4710ex29093090102-(Phenylmethoxy)naphthalene (CAS RN 613-62-7)0 %-31.12.2024 0.7176ex2909309015{[(2,2-Dimethylbut-3-yn-1-yl)oxy]methyl}benzene (CAS RN 1092536-54-3)0 %-31.12.20260.4711ex29093090201,2-Bis(3-methyl-phenoxy)ethane (CAS RN 54914-85-1)0 %-31.12.20240.7115ex29093090251,2-Diphenoxyethane (CAS RN 104-66-5) in the form of powder or as an aqueous dispersion containing by weight 30 % or more but not more than 60 % of 1,2-diphenoxyethane0 %-31.12.20260.5117ex29093090303,4,5-Trimethoxytoluene (CAS RN 6443-69-2)0 %-31.12.20250.7580ex29093090351-Chloro-2-(4-ethoxybenzyl)-4-iodobenzene (CAS RN 1103738-29-9)0 %-31.12.20240.6614ex29093090401-Chloro-2,5-dimethoxybenzene (CAS RN 2100-42-7)0 %-31.12.20250.8167ex29093090455-Bromo-1,3-difluoro-2-(trifluoromethoxy)benzene (CAS RN 115467-07-7) with a purity by weight of 95 % or more0 %-31.12.20260.6783ex29093090501-Ethoxy-2,3-difluorobenzene (CAS RN 121219-07-6)0 %-31.12.20250.6784ex29093090601-Butoxy-2,3-difluorobenzene (CAS RN 136239-66-2)0 %-31.12.20250.6994ex2909309070O,O,O-1,3,5-trimethylresorcinol (CAS RN 621-23-8)0 %-31.12.20260.7706ex29094400102-Propoxyethanol (CAS RN 2807-30-9)0 %-31.12.20240.6927ex29094980101-Propoxypropan-2-ol (CAS RN 1569-01-3)0 %-31.12.20260.8241ex29094980303,4-Dimethoxybenzyl alcohol (CAS RN 93-03-8) with a purity by weight of 98 % or more0 %-31.12.20260.8531ex29094980402,2’-p-Phenylenedioxydiethanol (CAS RN 104-38-1) with a purity by weight of 99 % or more0 %-31.12.20280.3484ex29095000104-(2-Methoxyethyl)phenol (CAS RN 56718-71-9)0 %-31.12.20240.7846ex29095000402-Methoxy-4-(trifluoromethoxy)phenol (CAS RN 166312-49-8) with a purity by weight of 98 % or more0 %-31.12.20240.3682ex2909609010Bis(α,α-dimethylbenzyl) peroxide (CAS RN 80-43-3)0 %-31.12.2024

0.6489ex29096090303,6,9-Triethyl-3,6,9-trimethyl-1,4,7-triperoxonane (CAS RN 24748-23-0), dissolved in isoparaffinic hydrocarbons0 %-31.12.20240.7910ex2909609050Solution of 3,6,9-(ethyl and/or propyl)-3,6,9-trimethyl-1,2,4,5,7,8-hexoxonanes (CAS RN 1613243-54-1) in mineral spirits (CAS RN 1174522-09-8), containing by weight 25 % or more, but not more than 41 % of the hexoxonanes0 %-31.12.20240.7744ex29109000102-[(2-Methoxyphenoxy)methyl]oxirane (CAS RN 2210-74-4)0 %-31.12.20240.5940ex29109000151,2-Epoxycyclohexane (CAS RN 286-20-4)0 %-31.12.20240.7672ex2910900025Phenyloxirane (CAS RN 96-09-3)0 %-31.12.20240.2649ex29109000302,3-Epoxypropan-1-ol (glycidol) (CAS RN 556-52-5)0 %-31.12.20240.8042ex2910900040[(2R)-Oxiran-2-yl]methyl 3-nitrobenzenesulphonate (CAS RN 115314-17-5) with a purity by weight of 97 % or more0 %-31.12.20250.6660ex29109000502,3-Epoxypropyl phenyl ether (CAS RN 122-60-1)0 %-31.12.20250.4361ex2910900080Allyl glycidyl ether (CAS RN 106-92-3)0 %-31.12.20260.7116ex2912190010Undecanal (CAS RN 112-44-7)0 %-31.12.20260.8073ex2912190020Acrylaldehyde (CAS RN 107-02-8) with a purity by weight of 98 % or more0 %-31.12.20250.6968ex29122900152,6,6-Trimethylcyclohexenecarbaldehyde (alpha-beta isomers mixture) (CAS RN 52844-21-0)0 %-31.12.20260.7314ex2912290035Cinnamaldehyde (CAS RN 104-55-2)0 %-31.12.20270.5755ex29122900504-Isobutylbenzaldehyde (CAS RN 40150-98-9)0 %-31.12.20240.7612ex2912290055Cyclohex-3-ene-1-carbaldehyde (CAS RN 100-50-5)0 %-31.12.20240.6072ex29122900704-tert-Butylbenzaldehyde (CAS RN 939-97-9)0 %-31.12.20240.6073ex29122900804-Isopropylbenzaldehyde (CAS RN 122-03-2)0 %-31.12.20240.814729124200Ethylvanillin (3-ethoxy-4-hydroxybenzaldehyde)0 %-31.12.20250.3479ex29124900103-Phenoxybenzaldehyde (CAS RN 39515-51-0)0 %-31.12.2024 0.5135ex2912490030Salicylaldehyde (CAS RN 90-02-8)0 %-31.12.20250.6678ex29124900403-Hydroxy-p-anisaldehyde (CAS RN 621-59-0)0 %-31.12.20250.7353ex29124900502,6-Dihydroxybenzaldehyde (CAS RN 387-46-2)0 %-31.12.20270.8582ex29124900604-Hydroxybenzaldehyde (CAS RN 123-08-0) with a purity by weight of 96 % or more0 %-31.12.20280.7712ex29130000102-Nitrobenzaldehyde (CAS RN 552-89-6)0 %-31.12.20240.8328ex29130000204-(Difluoromethoxy)-3-hydroxybenzaldehyde (CAS RN 151103-08-1) with a purity by weight of 98 % or more0 %-31.12.20240.8552ex29130000302-Hydroxy-5-nitrobenzaldehyde (CAS RN 97-51-8) with a purity by weight of 95 % or more0 %-31.12.20280.4228ex2914199020Heptan-2-one (CAS RN 110-43-0)0 %-31.12.20270.4274ex29141990303-Methylbutanone (CAS RN 563-80-4)0 %-31.12.20270.4275ex2914199040Pentan-2-one (CAS RN 107-87-9)0 %-31.12.20270.7554ex2914199060Zinc acetylacetonate (CAS RN 14024-63-6)0 %-31.12.20240.7568ex2914290015Oestr-5(10)-ene-3,17-dione (CAS RN 3962-66-1)0 %-31.12.20240.3475ex2914290020Cyclohexadec-8-enone (CAS RN 3100-36–5)0 %-31.12.20240.7450ex2914290025Cyclohex-2-enone (CAS RN 930-68-7)0 %-31.12.20240.4933ex2914290030(R)-p-Mentha-1(6),8-dien-2-one (CAS RN 6485-40-1)0 %-31.12.20250.8015ex29142900354-(trans-4-Propylcyclohexyl)cyclohexanone (CAS RN 82832-73-3) with a purity by weight of 95 % or more0 %-31.12.20250.3480ex2914290040Camphor0 %-31.12.20240.8058ex29142900454-Propylcyclohexan-1-one (CAS RN 40649-36-3) with a purity by weight of 95 % or more0 %-31.12.20250.7389ex29142900551-(Cedr-8-en-9-yl)ethanone (CAS RN 32388-55-9) with a purity by weight of more than 90 %0 %-31.12.20240.6265ex29143900152,6-Dimethyl-1-indanone (CAS RN 66309-83-9)0 %-31.12.20240.6447ex29143900251,3-Diphenylpropane-1,3-dione (CAS RN 120-46-7)0 %-31.12.2024

0.4227ex2914390030Benzophenone (CAS RN 119-61-9)0 %-31.12.20270.4429ex29143900504-Phenylbenzophenone (CAS RN 2128-93-0)0 %-31.12.20240.4428ex29143900604-Methylbenzophenone (CAS RN 134-84-9)0 %-31.12.20240.5739ex2914390070Benzil (CAS RN 134-81-6)0 %-31.12.20240.5535ex29143900804’-Methylacetophenone (CAS RN 122-00-9)0 %-31.12.20270.8288ex2914409010Benzoin (CAS RN 119-53-9) with a purity by weight of 99 % or more0 %-31.12.20260.7824ex29145000151,1-Dimethoxyacetone (CAS RN 6342-56-9) with a purity by weight of 98 % or more0 %-31.12.20240.8168ex29145000184’-Hydroxyacetophenone (CAS RN 99-93-4) with a purity by weight of 99 % or more0 %-31.12.20260.4932ex29145000203’-Hydroxyacetophenone (CAS RN 121-71-1)0 %-31.12.20250.8179ex29145000231-[2-(Oxiran-2-ylmethoxy)phenyl]-3-phenylpropan-1-one (CAS RN 22525-95-7) with a purity by weight of 99 % or more0 %-31.12.20260.5943ex29145000254’-Methoxyacetophenone (CAS RN 100-06-1)0 %-31.12.20240.8195ex29145000281,1’-{(2-Hydroxypropane-1,3-diyl)bis[oxy(6-hydroxybenzene-2,1-diyl)]}diethanone (CAS RN 16150-44-0) with a purity by weight of 98 % or more0 %-31.12.20260.6762ex29145000337-Hydroxy-3,4-dihydro-1(2H)-naphthalenone (CAS RN 22009-38-7) with a purity by weight of 98 % or more0 %-31.12.20240.7797ex29145000352-Hydroxy-1-[4-[4-(2-hydroxy-2-methylpropanoyl)phenoxy]phenyl]-2-methylpropan-1-one (CAS-RN 71868-15-0)0 %-31.12.20240.5904ex29145000362,7-Dihydroxy-9-fluorenone (CAS RN 42523-29-5)0 %-31.12.20240.5435ex29145000404-(4-Hydroxyphenyl)butan-2-one (CAS RN 5471-51-2)0 %-31.12.20260.5809ex29145000453,4-Dihydroxybenzophenone (CAS RN 10425-11-3)0 %-31.12.20270.4235ex29145000602,2-Dimethoxy-2-phenylacetophenone (CAS RN 24650-42-8)0 %-31.12.20270.4385ex29145000802’,6’-Dihydroxyacetophenone (CAS RN 699-83-2)0 %-31.12.2024 0.2647ex29146980102-Ethylanthraquinone (CAS RN 84-51-5)0 %-31.12.20240.2643ex29146980301,4-Dihydroxyanthraquinone (CAS RN 81-64-1)0 %-31.12.20240.5430ex2914698040p-Benzoquinone (CAS RN 106-51-4)0 %-31.12.20240.6481ex2914698050Reaction mass of 2-(1,2-dimethylpropyl)anthraquinone (CAS RN 68892-28-4) and 2-(1,1-dimethylpropyl)anthraquinone (CAS RN 32588-54-8)0 %-31.12.20240.7736ex29147900182-Chloro-1-cyclopropylethanone (CAS RN 7379-14-8)0 %-31.12.20240.5782ex29147900202,4’-Difluorobenzophenone (CAS RN 342-25-6)0 %-31.12.20270.7732ex29147900235-Chloro-2-hydroxybenzophenone (CAS RN 85-19-8)0 %-31.12.20240.7751ex2914790027(2-Chloro-5-iodo-phenyl)-(4-fluoro-phenyl)-methanone (CAS RN 915095-86-2)0 %-31.12.20240.7467ex29147900305-Methoxy-1-[4-(trifluoromethyl)phenyl]pentan-1-one (CAS RN 61718-80-7)0 %-31.12.20240.8338ex2914790033(4R)-4-(2-Fluorophenyl)-3,4-dihydro-2H-naphthalen-1-one (CAS RN 1234356-88-7) with a purity by weight of 99 % or more0 %-31.12.20270.7442ex29147900351-[4-(Benzyloxy)phenyl]-2-bromopropan-1-one (CAS RN 35081-45-9)0 %-31.12.20240.3474ex2914790040Perfluoro(2-methylpentan-3-one) (CAS RN 756-13-8)0 %-31.12.20240.8563ex29147900435-Chloropentan-2-one (CAS RN 5891-21-4) with a purity by weight of 95 % or more0 %-31.12.20280.8591ex29147900482-Chloro-3’,4’-dihydroxyacetophenone (CAS RN 99-40-1) with a purity by weight of 99 % or more0 %-31.12.20280.2640ex29147900503’-Chloropropiophenone (CAS RN 34841-35-5)0 %-31.12.20240.4948ex29147900604’-tert-Butyl-2’,6’-dimethyl-3’,5’-dinitroacetophenone (CAS RN 81-14-1)0 %-31.12.20260.5237ex29147900704-Chloro-4’-hydroxybenzophenone (CAS RN 42019-78-3)0 %-31.12.20260.6120ex2914790080Tetrachloro-p-benzoquinone (CAS RN 118-75-2)0 %-31.12.2024

0.7955ex2915240010Acetic anhydride (CAS RN 108-24-7) with a purity by weight of 97 % or more0 %-31.12.20250.8543ex29153900154-(2,2-Dichlorocyclopropyl)phenylacetate (CAS RN 144900-34-5) with a purity by weight of 97 % or more0 %-31.12.20280.6155ex29153900252-Methylcyclohexyl acetate (CAS RN 5726-19-2)0 %-31.12.20240.7433ex2915390035Cis-3-hexenyl acetate (CAS RN 3681-71-8) with a purity by weight of 95 % or more0 %-31.12.20270.2957ex2915390040tert-Butyl acetate (CAS RN 540-88-5)0 %-31.12.20240.7423ex29153900454-tert-Butylcyclohexyl acetate (CAS RN 32210-23-4) with a purity by weight of 95 % or more0 %-31.12.20270.5119ex2915390060Dodec-8-enyl acetate (CAS RN 28079-04-1)0 %-31.12.20250.5121ex2915390065Dodeca-7,9-dienyl acetate (CAS RN 54364-62-4)0 %-31.12.20250.5120ex2915390070Dodec-9-enyl acetate (CAS RN 16974-11-1)0 %-31.12.20250.5289ex2915390075Isobornyl acetate (CAS RN 125-12-2)0 %-31.12.20260.5301ex29153900801-Phenylethyl acetate (CAS RN 93-92-5)0 %-31.12.20260.5909ex29153900852-tert-Butylcyclohexyl acetate (CAS RN 88-41-5)0 %-31.12.20240.7834ex2915400010Ethyl trichloroacetate (CAS RN 515-84-4) with a purity by weight of 98 % or more0 %-31.12.20240.7830ex2915400020Sodium trichloroacetate (CAS RN 650-51-1) with a purity by weight of 96 % or more0 %-31.12.20240.5858ex2915601920Ethyl butyrate (CAS RN 105-54-4) with a purity by weight of 95 % or more0 %-31.12.20270.7540ex2915704010Methyl palmitate (CAS RN 112-39-0)0 %-31.12.20240.7541ex2915903010Methyl laurate (CAS RN 111-82-0)0 %-31.12.20250.8495ex2915903020Chloromethyl dodecanoate (CAS RN 61413-67-0) with a purity by weight of 97 % or more0 %-31.12.2027 0.7899ex2915907018Myristic acid, lithium salt (CAS RN 20336-96-3) with a purity by weight of 95 % or more0 %-31.12.20240.7407ex2915907020Methyl (R)-2-fluoropropionate (CAS RN 146805-74-5)0 %-31.12.20270.7542ex2915907025Methyl octanoate (CAS RN 111-11-5), methyl decanoate (CAS RN 110-42-9) or methyl myristate (CAS RN 124-10-7)0 %-31.12.20240.6003ex2915907027Triethyl orthoformate (CAS RN 122-51-0) with a purity by weight of 99 % or more0 %-31.12.20240.5767ex29159070303,3-Dimethylbutyryl chloride (CAS RN 7065-46-5)0 %-31.12.20270.8154ex2915907033Ethyl 8-bromooctanoate (CAS RN 29823-21-0) with a purity by weight of 98 % or more0 %-31.12.20260.5536ex29159070352,2-Dimethylbutanoyl chloride (CAS RN 5856-77-9)0 %-31.12.20240.8423ex2915907043Trifluoroacetic anhydride (CAS RN 407-25-0) with a purity by weight of 98 % or more0 %-31.12.20270.6255ex2915907045Trimethyl orthoformate (CAS RN 149-73-5)0 %-31.12.20240.4791ex2915907050Allyl heptanoate (CAS RN 142-19-8)0 %-31.12.20240.8457ex29159070533-Chloro-2,2-dimethylpropanoyl chloride (CAS RN 4300-97-4) with a purity by weight of 98 % or more0 %-31.12.20270.4954ex2915907060Ethyl-6,8-dichlorooctanoate (CAS RN 1070-64-0)0 %-31.12.20250.2585ex29161200102-tert-Butyl-6-(3-tert-butyl-2-hydroxy-5-methylbenzyl)-4-methylphenyl acrylate (CAS RN 61167-58-6)0 %-31.12.20240.3977ex29161200402,4-Di-tert-pentyl-6-[1-(3,5-di-tert-pentyl-2-hydroxyphenyl)ethyl]phenylacrylate (CAS RN 123968-25-2)0 %-31.12.20240.3466ex2916130030Zinc monomethacrylate powder (CAS RN 63451-47-8) whether or not containing not more than 17 % by weight of manufacturing impurities0 %-31.12.20250.3468ex2916130040Zinc Dimethacrylate (CAS RN 13189-00-9) in the form of powder with a purity by weight of 99 % or more, with not more than 1 % of a stabiliser0 %-31.12.2024

0.2638ex29161400102,3-Epoxypropyl methacrylate (CAS RN 106-91-2)0 %-31.12.20240.6190ex2916140020Ethyl methacrylate (CAS RN 97-63-2)0 %-31.12.20240.2951ex2916199520Methyl 3,3-dimethylpent-4-enoate (CAS RN 63721-05-1)0 %-31.12.20240.5991ex2916199540Sorbic acid (CAS RN 110-44-1) for use in the manufacture of animal feeds0 %-31.12.20240.6238ex2916199550Methyl 2-fluoroacrylate (CAS RN 2343-89-7)0 %-31.12.20240.7980ex2916199560Methyl 2-fluoroprop-2-enoate (CAS RN 2343-89-7) with a purity by weight of 93 % or more, whether or not with not more than 7 % of the stabiliser 2,6-di-tert-butyl-p-cresol (CAS RN 128-37-0) and Tetrabutylammonium nitrite (CAS RN 26501-54-2)0 %-31.12.20250.7940ex2916199570Methyl 3-methyl-2-butenoate (CAS RN 924-50-5) with a purity by weight of 99,0 % or more0 %-31.12.20250.7023ex2916200015Transfluthrin (ISO) (CAS RN 118712-89-3)0 %-31.12.20260.7931ex2916200025Cyclohexanecarbonyl chloride (CAS RN 2719-27-9) with a purity by weight of 99 % or more0 %-31.12.20250.7933ex29162000352-Cyclopropylacetic acid (CAS RN 5239-82-7) with a purity by weight of 95 % or more0 %-31.12.20250.8057ex2916200045Cyclopentanecarboxylic acid (CAS RN 3400-45-1) with a purity by weight of 98 % or more0 %-31.12.20250.3463ex2916200050Ethyl 2,2-dimethyl-3-(2-methylpropenyl)cyclopropanecarboxylate (CAS RN 97-41-6)0 %-31.12.20240.8336ex2916200055Methyl 2,2-dimethyl-3-(2-methylprop-1-en-1-yl)cyclopropane-1-carboxylate (CAS RN 5460-63-9) with a purity by weight of 90 % or more0 %-31.12.20270.4931ex29162000603-Cyclohexylpropionic acid (CAS RN 701-97-3)0 %-31.12.20250.8352ex2916200065Tefluthrin (ISO)(CAS RN 79538-32-2) with a purity by weight of 96 % or more0 %-31.12.2027 0.7531ex2916200070Cyclopropanecarbonyl chloride (CAS RN 4023-34-1)0 %-31.12.20240.5421ex2916310010Benzyl benzoate (CAS RN 120-51-4)0 %-31.12.20260.8214ex2916310020Phenethyl benzoate (CAS RN 94-47-3) with a purity by weight of 95 % or more0 %-31.12.20260.6248ex29163990133,5-Dinitrobenzoic acid (CAS RN 99-34-3)0 %-31.12.20240.5214ex29163990152-Chloro-5-nitrobenzoic acid (CAS RN 2516-96-3)0 %-31.12.20260.7929ex29163990163-Fluoro-5-iodo-4-methylbenzoic acid (CAS RN 861905-94-4) with a purity by weight of 97 % or more0 %-31.12.20250.2636ex29163990203,5-Dichlorobenzoyl chloride (CAS RN 2905-62-6)0 %-31.12.20240.7845ex29163990226-Bromo-2-fluoro-3-(trifluoromethyl)benzoic acid (CAS RN 1026962-68-4) with a purity by weight of 95 % or more0 %-31.12.20240.6557ex2916399023(2,4,6-Trimethylphenyl)acetyl chloride (CAS RN 52629-46-6)0 %-31.12.20240.4951ex29163990252-Methyl-3-(4-Fluorophenyl)-propionyl chloride (CAS RN 1017183-70-8)0 %-31.12.20260.7827ex2916399027Methyl 6-Bromo-2-naphthoate (CAS RN 33626-98-1) with a purity by weight of 99 % or more0 %-31.12.20240.4930ex29163990302,4,6-Trimethylbenzoyl chloride (CAS RN 938-18-1)0 %-31.12.20250.5944ex2916399035Methyl 4-tert-butylbenzoate (CAS RN 26537-19-9)0 %-31.12.20240.8489ex2916399040Ethyl 4-bromo-3-(bromomethyl)benzoate (CAS RN 347852-72-6) with a purity by weight of 97 % or more0 %-31.12.20270.6794ex29163990414-Bromo-2,6-difluorobenzoyl chloride (CAS RN 497181-19-8)0 %-31.12.20250.7734ex29163990432-(3,5-Bis(trifluoromethyl)phenyl)-2-methylpropanoic acid (CAS RN 289686-70-0)0 %-31.12.20240.6121ex29163990483-Fluorobenzoyl chloride (CAS RN 1711-07-5)0 %-31.12.20240.2634ex29163990503,5-Dimethylbenzoyl chloride (CAS RN 6613-44-1)0 %-31.12.20240.6661ex29163990535-Iodo-2-methylbenzoic acid (CAS RN 54811-38-0)0 %-31.12.2025

0.4238ex29163990554-tert-Butylbenzoic acid (CAS RN 98-73-7 )0 %-31.12.20270.7678ex29163990572-Phenylprop-2-enoic acid (CAS RN 492-38-6)0 %-31.12.20240.8169ex29163990632-Phenylbutyric acid (CAS RN 90-27-7) with a purity by weight of 99 % or more0 %-31.12.20260.8369ex2916399067Nitrobenzoic acid (CAS RN 62-23-7) with a purity by weight of 99 % or more0 %-31.12.20270.3462ex2916399070Ibuprofen (INN) (CAS RN 15687-27-1)0 %-31.12.20240.7117ex2916399073(2,4-Dichlorophenyl)acetyl chloride (CAS RN 53056-20-5)0 %-31.12.20260.5541ex2916399075m-Toluic acid (CAS RN 99-04-7)0 %-31.12.20270.8039ex2916399078(2,5-Dibromophenyl)acetic acid (CAS RN 203314-28-7) with a purity by weight of 98,0 % or more0 %-31.12.20250.5543ex2916399085(2,4,5-Trifluorophenyl)acetic acid (CAS RN 209995-38-0)0 %-31.12.20270.3457ex2917110020Bis(p-methylbenzyl) oxalate (CAS RN 18241-31-1)0 %-31.12.20240.4746ex2917110030Cobalt oxalate (CAS RN 814-89-1)0 %-31.12.20240.7563ex2917120020Bis(3,4-epoxycyclohexylmethyl) adipate (CAS RN 3130-19-6)0 %-31.12.20240.4684ex2917191010Dimethyl malonate (CAS RN 108-59-8)0 %-31.12.20240.5602ex2917191020Diethyl malonate (CAS RN 105-53-3)0 %-31.12.20270.6089ex2917198015Dimethyl but-2-ynedioate (CAS RN 762-42-5)0 %-31.12.20240.4790ex2917198030Ethylene brassylate (CAS RN 105-95-3)0 %-31.12.20240.7451ex2917198035Diethyl methylmalonate (CAS RN 609-08-5)0 %-31.12.20240.7880ex2917198045Iron fumarate (CAS RN 141-01-5) with a purity by weight of 93 % or more0 %-31.12.20240.4918ex2917198050Tetradecanedioic acid (CAS RN 821-38-5)0 %-31.12.20250.8302ex2917198055Maleic acid (CAS RN 110-16-7) with a purity by weight of 99 % or more3,2 %-31.12.2024 0.8530ex2917198060Oxalyl dichloride (CAS RN 79-37-8) with a purity by weight of 99 % or more0 %-31.12.20280.3454ex2917198070Itaconic acid (CAS RN 97-65-4)0 %-31.12.20240.8534ex2917198080Ethyl chloroglyoxylate (CAS RN 4755-77-5) with a purity by weight of 98 % or more0 %-31.12.20280.2631ex29172000301,4,5,6,7,7-Hexachloro-8,9,10-trinorborn-5-ene-2,3-dicarboxylic anhydride (CAS RN 115-27-5)0 %-31.12.20240.2627ex29172000403-Methyl-1,2,3,6-tetrahydrophthalic anhydride (CAS RN 5333-84-6)0 %-31.12.20240.2954ex2917340010Diallyl phthalate (CAS RN 131-17-9)0 %-31.12.20240.4945ex2917398520Dibutyl-1,4-benzenedicarboxylate (CAS RN 1962-75-0)0 %-31.12.20250.6796ex2917398525Naphthalene-1,8-dicarboxylic anhydride (CAS RN 81-84-5)0 %-31.12.20250.3640ex2917398530Benzene-1,2:4,5-tetracarboxylic dianhydride (CAS RN 89-32-7)0 %-31.12.20250.6800ex29173985351-Methyl-2-nitroterephthalate (CAS RN 35092-89-8)0 %-31.12.20250.6123ex2917398540Dimethyl 2-nitroterephthalate (CAS RN 5292-45-5)0 %-31.12.20240.8255ex29173985453-(4-Chlorophenyl)glutaric acid (CAS RN 35271-74-0) with a purity by weight of 98 % or more0 %-31.12.20260.6553ex29173985501,4,5,8-Naphthalenetetracarboxylic acid-1,8-monoanhydride (CAS RN 52671-72-4)0 %-31.12.20240.8526ex29173985553-Nitrophthalic acid (CAS RN 603-11-2) with a purity by weight of 98 % or more0 %-31.12.20280.6554ex2917398560Perylene-3,4:9,10-tetracarboxylic dianhydride (CAS RN 128-69-8)0 %-31.12.20240.6366ex2918193010Cholic acid (CAS RN 81-25-4)0 %-31.12.20240.6367ex29181930203-α,12-α-Dihydroxy-5-β-cholan-24-oic acid (deoxycholic acid) (CAS RN 83-44-3)0 %-31.12.20240.2950ex2918199820L-Malic acid (CAS RN 97-67-6)0 %-31.12.20240.8509ex2918199825(S)-2-Hydroxy-2-phenylacetic acid (CAS RN 17199-29-0) with a purity by weight of 99 % or more0 %-31.12.2027

0.7702ex2918199830Ethyl 1-hydroxycyclopentanecarboxylate (CAS RN 41248-23-1)0 %-31.12.20240.7703ex2918199840Ethyl 1-hydroxycyclohexanecarboxylate (CAS RN 1127-01-1)0 %-31.12.20240.7907ex291819985012-Hydroxyoctadecanoic acid (CAS RN 106-14-9) with a purity by weight of 90 % or more for use in the manufacture of polyglycerin-poly-12-hydroxyoctadecanoic acid esters0 %-31.12.20240.8044ex2918199860(R)-tert-Butyl 2’-(1-hydroxyethyl)-3-methyl-[1,1’-biphenyl]-4-carboxylate (CAS RN 1246560-92-8) with a purity by weight of 98 % or more0 %-31.12.20250.8422ex2918199870Rac-tert-butyl 3-hydroxy-4-pentenoate (CAS RN 122763-67-1) with a purity by weight of 98 % or more0 %-31.12.20270.3637ex2918290010Monohydroxynaphthoic acids0 %-31.12.20240.5781ex2918290035Propyl 3,4,5-trihydroxybenzoate (CAS RN 121-79-9)0 %-31.12.20270.8008ex29182900403-Hydroxy-4-nitrobenzoic acid (CAS RN 619-14-7) with a purity by weight of more than 96,5 %0 %-31.12.20250.3638ex2918290050Hexamethylene bis[3-(3,5-di-tert-butyl-4-hydroxyphenyl)propionate] (CAS RN 35074-77-2)0 %-31.12.20240.5220ex2918290060Methyl-, ethyl-, propyl- or butyl esters of 4-hydroxybenzoic acid or their sodium salts (CAS RN 35285-68-8, 99-76-3, 5026-62-0, 94-26-8, 94-13-3, 35285-69-9, 120-47-8, 36457-20-2 or 4247-02-3)0 %-31.12.20260.6456ex29182900703,5-Diiodosalicylic acid (CAS RN 133-91-5)0 %-31.12.20240.7605ex2918300025(E)-1-ethoxy-3-oxobut-1-en-1-olate; 2-methylpropan-1-olate; titanium(4+) (CAS RN 83877-91-2)0 %-31.12.20240.4427ex2918300030Methyl-2-benzoylbenzoate (CAS RN 606-28-0)0 %-31.12.20240.7864ex29183000353-Oxocyclobutane-1-carboxylic acid with a purity by weight of 98 % or more (CAS RN 23761-23-1)0 %-31.12.20240.8075ex2918300045Methyl 5-oxo-6,7,8,9-tetrahydro-5H-benzo[7]annulene-2-carboxylate (CAS RN 150192-89-5) with a purity by weight of 96 % or more0 %-31.12.2025 0.8256ex2918300055Methyl 3-oxo-pentanoate (CAS RN 30414-53-0) with a purity by weight of 98 % or more0 %-31.12.20260.6250ex29183000604-Oxovaleric acid (CAS RN 123-76-2)0 %-31.12.20240.6455ex29183000702-[4-Chloro-3-(chlorosulphonyl)benzoyl]benzoic acid (CAS RN 68592-12-1)0 %-31.12.20240.8342ex2918300075Methyl 2-((1S,2R)-3-oxo-2-pentylcyclopentyl)acetate (CAS RN 151716-35-7) with a purity by weight of 99 % or more0 %-31.12.20270.7062ex2918300080Methyl benzoylformate (CAS RN 15206-55-0)0 %-31.12.20260.7344ex29183000852-Fluoro-5-formylbenzoic acid (CAS RN 550363-85-4) with a purity by weight of 98 % or more0 %-31.12.20240.5857ex2918300087Ethyl acetoacetate (CAS RN 141-97-9) with a purity by weight of 98 % or more0 %-31.12.20270.2946ex29189990103,4-Epoxycyclohexylmethyl 3,4-epoxycyclohexanecarboxylate (CAS RN 2386-87-0)0 %-31.12.20240.6814ex29189990133-Methoxy-2-methylbenzoyl chloride (CAS RN 24487-91-0)0 %-31.12.20250.5856ex2918999015Ethyl 2,3-epoxy-3-phenylbutyrate (CAS RN 77-83-8)0 %-31.12.20270.6901ex2918999018Ethyl 2-hydroxy-2-(4-phenoxyphenyl)propanoate (CAS RN 132584-17-9)0 %-31.12.20250.2949ex2918999020Methyl 3-methoxyacrylate (CAS RN 5788-17-0)0 %-31.12.20240.6147ex2918999025Methyl (E)-3-methoxy-2-(2-chloromethylphenyl)-2-propenoate (CAS RN 117428-51-0)0 %-31.12.20240.7256ex2918999027Ethyl 3-ethoxypropionate (CAS RN 763-69-9)0 %-31.12.20270.2948ex2918999030Methyl 2-(4-hydroxyphenoxy)propionate (CAS RN 96562-58-2)0 %-31.12.20240.7597ex2918999033

Vanillic Acid (CAS RN 121-34-6) containing not more than 10 ppm of Palladium (CAS RN 7440-05-3), not more than 10 ppm of bismuth (CAS RN 7440-69-9), not more than 14 ppm of formaldehyde (CAS RN 50-00-0), not more than 1,3 % by weight of 3,4-dihydroxybenzoic acid (CAS RN 99-50-3), not more than 0,5 % by weight of vanillin (CAS RN 121-33-5) 0 %-31.12.2024 0.6342ex2918999035p-Anisic acid (CAS RN 100-09-4)0 %-31.12.20240.7358ex2918999038Diclofop-methyl (ISO) (CAS RN 51338-27-3)0 %-31.12.20270.2945ex2918999040trans-4-Hydroxy-3-methoxycinnamic acid (CAS RN 1135-24-6)0 %-31.12.20240.7934ex2918999043Vanillic acid (CAS RN 121-34-6) with a purity by weight of 98,5 % or more0 %-31.12.20250.6224ex29189990454-Methylcatechol dimethyl acetate (CAS RN 52589-39-6)0 %-31.12.20240.8066ex29189990482-Bromo-5-methoxybenzoic acid (CAS RN 22921-68-2) with a purity by weight of 98 % or more0 %-31.12.20250.2947ex2918999050Methyl 3,4,5-trimethoxybenzoate (CAS RN 1916-07-0)0 %-31.12.20240.6552ex2918999055Stearyl glycyrrhetinate(CAS RN 13832-70-7)0 %-31.12.20240.2943ex29189990603,4,5-Trimethoxybenzoic acid (CAS RN 118-41-2)0 %-31.12.20240.6523ex2918999065Acetic acid, difluoro[1,1,2,2-tetrafluoro-2-(pentafluoroethoxy)ethoxy]-, ammonium salt (CAS RN 908020-52-0)0 %-31.12.20240.4742ex2918999070Allyl-(3-methylbutoxy)acetate (CAS RN 67634-00-8)0 %-31.12.20240.6747ex2918999085Trinexapac-Ethyl (ISO) (CAS RN 95266-40-3) with a purity by weight of 96 % or more0 %-31.12.20250.7723ex2919900025Triphenyl phosphate (CAS RN 115-86-6)0 %-31.12.20240.2940ex2919900030Aluminium hydroxybis[2,2’-methylenebis(4,6-di-tert-butylphenyl)phosphate] (CAS RN 151841-65-5)0 %-31.12.20240.2942ex29199000352,2’-Methylenebis(4,6-di-tert-butylphenyl) phosphate, monosodium salt (CAS RN 85209-91-2) with a purity by weight of 95 % or more, with particles greater than 100µm used in the manufacture of nucleating agents with a particle size (D90) no greater than 35 µm as measured by a light scattering technique0 %-31.12.20240.3867ex2919900040Tri-n-hexylphosphate (CAS RN 2528-39-4)0 %-31.12.20240.5495ex2919900050Triethyl phosphate (CAS RN 78-40-0)0 %-31.12.20260.6188ex2919900060Bisphenol-A bis(diphenyl phosphate) (CAS RN 5945-33-5)0 %-31.12.2024 0.6413ex2919900070Tris(2-butoxyethyl)phosphate (CAS RN 78-51-3)0 %-31.12.20240.6253ex29201900302,2’-Oxybis(5,5-dimethyl-1,3,2-dioxaphosphorinane)-2,2’-disulphide (CAS RN 4090-51-1)0 %-31.12.20240.2941ex2920190040Tolclofos-methyl (ISO) (CAS RN 57018-04-9) with a purity by weight of 96 % or more0 %-31.12.20240.363429202300Trimethyl phosphite (CAS RN 121-45-9)0 %-31.12.20240.415829202400Triethyl phosphite (CAS RN 122-52-1)0 %-31.12.20260.2626ex2920290010O,O’-Dioctadecyl pentaerythritol bis(phosphite) (CAS RN 3806-34-6)0 %-31.12.20240.5038ex2920290020Tris(methylphenyl)phosphite (CAS RN 25586-42-9)0 %-31.12.20250.5045ex2920290040Bis(2,4-dicumylphenyl)pentaerythritol diphosphite (CAS RN 154862-43-8)0 %-31.12.20250.6004ex2920290050Fosetyl-aluminium (CAS RN 39148-24-8)0 %-31.12.20240.7898ex29202900802,4,8,10-Tetrakis(1,1-dimethylethyl)-6-(2-ethylhexyloxy)-12H dibenzo[d,g][1,3,2]dioxaphosphocin (CAS RN 126050-54-2) with a purity by weight of 95 % or more0 %-31.12.20240.8522ex2920901013Tetraethyl orthocarbonate (CAS RN 78-09-1) with a purity by weight of 99 % or more0 %-31.12.20280.7559ex2920901015Ethyl methyl carbonate (CAS RN 623-53-0)3,2 %-31.12.20240.2605ex2920901020Diallyl 2,2’-oxydiethyl dicarbonate (CAS RN 142-22-3)0 %-31.12.20240.3685ex2920901040Dimethyl carbonate (CAS RN 616-38-6)0 %-31.12.20240.8297ex2920901045Ethylene carbonate (CAS RN 96-49-1) with a purity by weight of 99 % or more3,2 %-31.12.20240.3868ex2920901050Di-tert-butyl dicarbonate (CAS RN 24424-99-5)0 %-31.12.20240.8298ex2920901055Vinylene carbonate (CAS RN 872-36-6) with a purity by weight of 99,9 % or more3,2 %-31.12.20240.8299ex2920901065Vinyl ethylene carbonate (CAS RN 4427-96-7) with a purity by weight of 99 % or more3,2 %-31.12.2024

0.8511ex2920901085Diethyl carbonate (CAS RN 105-58-8) with a purity by weight of 99,9 % or more3,2 %-31.12.20240.8542ex2920907010Tris(2-propylheptyl) borate (CAS RN 1488321-95-4) with a purity by weight of 90 % or more0 %-31.12.20280.7588ex2920907020Diethyl phosphorochloridate (CAS RN 814-49-3)0 %-31.12.20240.7465ex29209070302-Isopropoxy-4,4,5,5-tetramethyl-1,3,2-dioxaborolane (CAS RN 61676-62-8)0 %-31.12.20240.5947ex2920907060Bis(neopentylglycolato)diboron (CAS RN 201733-56-4)0 %-31.12.20240.8490ex29209070704,4,5,5-Tetramethyl-1,3,2-dioxaborolane (CAS RN 25015-63-8) with a purity by weight of 97 % or more, containing not more than 1 % of the stabiliser triethylamine (CAS RN 121-44-8)0 %-31.12.20270.6598ex2920907080Bis(pinacolato)diboron (CAS RN 73183-34-3)0 %-31.12.20250.5668ex2921130010Aqueous solution containing by weight 63 % or more, but not more than 67 % of 2-(N,N-Diethylamino)ethylchloride hydrochloride0 %-31.12.20240.3629ex2921199920Ethyl(2-methylallyl)amine (CAS RN 18328-90-0)0 %-31.12.20240.3631ex2921199930Allylamine (CAS RN 107-11-9)0 %-31.12.20240.8477ex2921199935N-Ethyl-N-isopropylpropan-2-amine 2-(difluoromethoxy)acetate with a purity by weight of 98 % or more0 %-31.12.20270.7073ex29211999452-Chloro-N-(2-chloroethyl)ethanamine hydrochloride (CAS RN 821-48-7)0 %-31.12.20260.8562ex29211999552,2,2-Trifluoroethylamine hydrochloride (CAS RN 373-88-6) with a purity by weight of 99 % or more0 %-31.12.20280.6269ex2921199980Taurine (CAS RN 107-35-7), with 0,5 % addition of anti-caking agent silicon dioxide (CAS RN 112926-00-8)0 %-31.12.20240.8045ex2921290015(2S)-Propane-1,2-diamine dihydrochloride (CAS RN 19777-66-3) with a purity by weight of 98 % or more0 %-31.12.2025 0.3630ex2921290020Tris[3-(dimethylamino)propyl]amine (CAS RN 33329-35-0)0 %-31.12.20240.8067ex2921290025N,N’-Diallylpropane-1,3-diamine dihydrochloride (CAS RN 205041-15-2) with a purity by weight or 96 % or more0 %-31.12.20250.3625ex2921290030Bis[3-(dimethylamino)propyl]methylamine (CAS RN 3855-32-1)0 %-31.12.20240.8170ex2921290035Pentamethylenediamine (CAS RN 462-94-2) with a purity by weight of 99 % or more, also as an aqueous solution containing by weight more than 50 % of pentamethylenediamine0 %-31.12.20260.4917ex2921290040Decamethylenediamine (CAS RN 646-25-3)0 %-31.12.20250.5256ex2921290050N’-[3-(Dimethylamino)propyl]-N,N-dimethylpropane-1,3-diamine (CAS RN 6711-48-4)0 %-31.12.20260.7947ex2921290070N,N,N’,N’-Tetramethylethylenediamine (CAS RN 110-18-9) with a purity by weight of 99 % or more0 %-31.12.20250.7488ex29213010102-(4-(Cyclopropanecarbonyl)phenyl)-2-methylpropanoic acid cyclohexylamine salt (CAS RN 1690344-90-1)0 %-31.12.20240.5768ex2921309940Cyclopropylamine (CAS RN 765-30-0)0 %-31.12.20270.7750ex2921309950Bicyclo[1.1.1]pentan-1-amine hydrochloride (CAS RN 22287-35-0)0 %-31.12.20240.8529ex2921309960Amantadine hydrochloride (CAS RN 665-66-7) with a purity by weight of 97 % or more0 %-31.12.20280.3909ex2921420025Sodium hydrogen 2-aminobenzene-1,4-disulphonate (CAS RN 24605-36-5)0 %-31.12.20240.3978ex29214200352-Nitroaniline (CAS RN 88-74-4)0 %-31.12.20240.3979ex29214200452,4,5-Trichloroaniline (CAS RN 636-30-6)0 %-31.12.20240.2620ex29214200503-Aminobenzenesulfonic acid (CAS RN 121-47-1)0 %-31.12.20240.7739ex29214200554-Chloroaniline (CAS RN 106-47-8)0 %-31.12.20240.3623ex29214200702-Aminobenzene-1,4-disulfonic acid (CAS RN 98-44-2)0 %-31.12.20240.3622ex29214200804-Chloro-2-nitroaniline (CAS RN 89-63-4)0 %-31.12.2024

0.3687ex29214200853,5-Dichloroaniline (CAS RN 626-43-7)0 %-31.12.20240.5616ex29214200862,5-Dichloroaniline (CAS RN 95-82-9)0 %-31.12.20270.5603ex2921420087N-Methylaniline (CAS RN 100-61-8)0 %-31.12.20270.5617ex29214200883,4-Dichloroaniline-6-sulphonic acid (CAS RN 6331-96-0)0 %-31.12.20270.2617ex29214300204-Amino-6-chlorotoluene-3-sulphonic acid (CAS RN 88-51-7)0 %-31.12.20240.8433ex29214300256-Chloro-α,α,α-trifluoro-m-toluidine (CAS RN 121-50-6) with a purity by weight of 98 % or more0 %-31.12.20270.2615ex29214300303-Nitro-p-toluidine (CAS RN 119-32-4)0 %-31.12.20240.8568ex29214300353-Chloro-o-toluidine (CAS RN 87-60-5) with a purity by weight of 95 % or more0 %-31.12.20280.3980ex29214300404-Aminotoluene-3-sulphonic acid (CAS RN 88-44-8)0 %-31.12.20240.5124ex29214300603-Aminobenzotrifluoride (CAS RN 98-16-8)0 %-31.12.20250.7583ex29214300705-Bromo-4-fluoro-2-methylaniline (CAS RN 627871-16-3)0 %-31.12.20240.3621ex2921440020Diphenylamine (CAS RN 122-39-4)0 %-31.12.20240.2618ex29214500202-Aminonaphthalene-1,5-disulphonic acid (CAS RN 117-62-4) or one of its sodium salts (CAS RN 19532-03-7) or (CAS RN 62203-79-6)0 %-31.12.20240.7628ex2921450030(5 or 8)-Aminonaphthalene-2-sulphonic acid (CAS RN 51548-48-2)0 %-31.12.20240.5994ex29214500507-Aminonaphthalene-1,3,6-trisulphonic acid (CAS RN 118-03-6)0 %-31.12.20240.7316ex29214500601-Naphthylamine (CAS RN 134-32-7)0 %-31.12.20270.7629ex29214500802-Aminonaphthalene-1-sulphonic acid (CAS RN 81-16-3)0 %-31.12.20240.3618ex2921490020Pendimethalin (ISO) (CAS RN 40487-42-1)3,5 %-31.12.20240.7705ex29214900304-Isopropylaniline (CAS RN 99-88-7)0 %-31.12.20240.7592ex29214900352-Ethylaniline (CAS RN 578-54-1)0 %-31.12.20240.2609ex2921490040N-1-Naphthylaniline (CAS RN 90-30-2)0 %-31.12.2024 0.8019ex29214900452-(4-Biphenylyl)amino-9,9-dimethylfluoren (CAS RN 897671-69-1) with a purity by weight of 95 % or more0 %-31.12.20250.8020ex29214900552-(2-Biphenylyl)amino-9,9-dimethylfluoren (CAS RN 1198395-24-2) with a purity by weight of 95 % or more0 %-31.12.20250.6825ex29214900602,6-Diisopropylaniline (CAS RN 24544-04-5)0 %-31.12.20250.8059ex2921490065Bis-(9,9-dimethylfluoren-2-yl)amine (CAS RN 500717-23-7) with a purity by weight of 95 % or more0 %-31.12.20250.8558ex2921490075N-Methyl-1-(1-napthyl)methanamine (CAS RN 14489-75-9) with a purity by weight of 99 % or more0 %-31.12.20280.3981ex29215119302-Methyl-p-phenylenediamine sulphate (CAS RN 615-50-9)0 %-31.12.20240.4184ex2921511940p-Phenylenediamine (CAS RN 106-50-3)0 %-31.12.20260.4498ex2921511950Mono- and dichloroderivatives of p-phenylenediamine and p-diaminotoluene0 %-31.12.20240.5995ex29215119602,4-Diaminobenzenesulphonic acid (CAS RN 88-63-1)0 %-31.12.20240.7894ex2921519010N-(4-Chlorophenyl)benzene-1,2-diamine (CAS RN 68817-71-0) with a purity by weight of 97 % or more0 %-31.12.20240.2612ex2921599015Mixture of isomers of 3,5-diethyltoluenediamine (CAS RN 68479-98-1)0 %-31.12.20280.3785ex29215990303,3’-Dichlorobenzidine dihydrochloride (CAS RN 612-83-9)0 %-31.12.20270.3870ex29215990404,4’-Diaminostilbene–2,2’-disulphonic acid (CAS RN 81-11-8)0 %-31.12.20240.7860ex2922190015

Aqueous solution, containing by weight: 73 % or more 2-amino-2-methyl-1-propanol (CAS RN 124-68-5), 4,5 % or more, but not more than 27 % water (CAS RN 7732-18-5) 0 %-31.12.20240.5757ex29221900202-(2-Methoxyphenoxy)ethylamine hydrochloride (CAS RN 64464-07-9)0 %-31.12.20270.7946ex2922190029N-Methyl-N-(2-hydroxyethyl)-p-toluidine (CAS RN 2842-44-6) with a purity by weight of 99 % or more0 %-31.12.2025 0.3617ex2922190030N,N,N’,N’-Tetramethyl-2,2’-oxybis(ethylamine) (CAS RN 3033-62-3)0 %-31.12.20240.8337ex29221900332-Methoxyethan-1-amine (CAS RN 109-85-3) with a purity by weight of 98 % or more0 %-31.12.20270.6947ex29221900352-[2-(Dimethylamino)ethoxy] ethanol (CAS RN 1704-62-7)0 %-31.12.20250.7179ex2922190040(R)-1-((4-Amino-2-bromo-5-fluorophenyl)amino)-3-(benzyloxy)propan-2-ol 4-methylbenzenesulphonate (CAS RN 1294504-64-5)0 %-31.12.20260.7480ex29221900452-Methoxymethyl-p-phenylenediamine (CAS RN 337906-36-2)0 %-31.12.20240.3616ex29221900532-(2-Methoxyphenoxy)ethanamine (CAS RN 1836-62-0) with a purity by weight of 98 % or more0 %-31.12.20240.7587ex29221900553-Aminoadamantan-1-ol (CAS RN 702-82-9)0 %-31.12.20240.3871ex2922190060N,N,N’-Trimethyl-N’-(2-hydroxy-ethyl) 2,2’-oxybis(ethylamine), (CAS RN 83016-70-0)0 %-31.12.20240.5905ex2922190065trans-4-Aminocyclohexanol (CAS RN 27489-62-9)0 %-31.12.20240.7935ex29221900702-Benzylaminoethanol (CAS 104-63-2) with a purity by weight of 98 % or more0 %-31.12.20250.5986ex29221900752-Ethoxyethylamine (CAS RN 110-76-9)0 %-31.12.20240.4665ex2922190080N-[2-[2-(Dimethylamino)ethoxy]ethyl]-N-methyl-1,3-propanediamine (CAS RN 189253-72-3)0 %-31.12.20240.5911ex2922190085(1S,4R)-cis-4-Amino-2-cyclopentene-1-methanol-D-tartrate (CAS RN 229177-52-0)0 %-31.12.20240.5996ex29222100102-Amino-5-hydroxynaphthalene-1,7-disulphonic acid (CAS RN 6535-70-2)0 %-31.12.20240.2703ex29222100306-Amino-4-hydroxynaphthalene-2-sulphonic acid (CAS RN 90-51-7)0 %-31.12.20240.2704ex29222100407-Amino-4-hydroxynaphthalene-2-sulphonic acid (CAS RN 87-02-5)0 %-31.12.2024 0.3873ex2922210050Sodium hydrogen 4-amino-5-hydroxynaphthalene-2,7-disulphonate (CAS RN 5460-09-3)0 %-31.12.20240.5997ex29222100604-Amino-5-hydroxynaphthalene-2,7-disulphonic acid with a purity by weight of 80 % or more (CAS RN 90-20-0)0 %-31.12.20240.8564ex29222900132-(4-Chlorophenoxy)-5-(trifluoromethyl)aniline (CAS RN 349-20-2) with a purity by weight of 98 % or more0 %-31.12.20280.2702ex29222900203-Aminophenol (CAS RN 591-27-5)0 %-31.12.20240.3982ex29222900255-Amino-o-cresol (CAS RN 2835-95-2)0 %-31.12.20240.6624ex29222900301,2-Bis(2-aminophenoxy)ethane (CAS RN 52411-34-4)0 %-31.12.20250.7642ex2922290033o-Phenetidine (CAS RN 94-70-2)0 %-31.12.20240.6634ex2922290063Aclonifen (ISO) (CAS RN 74070-46-5) with a purity by weight of 97 % or more0 %-31.12.20250.4627ex29222900654-Trifluoromethoxyaniline (CAS RN 461-82-5)0 %-31.12.20240.7481ex29222900674-Chloro-2,5-dimethoxyaniline (CAS RN 6358-64-1)0 %-31.12.20240.2692ex29222900704-Nitro-o-anisidine (CAS RN 97-52-9)0 %-31.12.20240.7026ex2922290073Tris(4-aminophenyl) thiophosphate (CAS RN 52664-35-4)0 %-31.12.20260.4956ex29222900754-(2-Aminoethyl)phenol (CAS RN 51-67-2)0 %-31.12.20250.2696ex29222900803-Diethylaminophenol (CAS RN 91-68-9)0 %-31.12.20240.5898ex29222900854-Benzyloxyaniline hydrochloride (CAS RN 51388-20-6)0 %-31.12.20240.2690ex29223900101-Amino-4-bromo-9,10-dioxoanthracene-2-sulphonic acid and its salts0 %-31.12.20240.4914ex29223900202-Amino-5-chlorobenzophenone (CAS RN 719-59-5)0 %-31.12.20250.7713ex2922390030(2-Fluorophenyl)-[2-(methylamino)-5-nitrophenyl]methanone (CAS RN 735-06-8)0 %-31.12.20240.6761ex29223900355-Chloro-2-(methylamino)benzophenone (CAS RN 1022-13-5)0 %-31.12.20250.7800ex29223900404,4’-Bis(diethylamino)benzophenone (CAS RN 90-93-7)0 %-31.12.2024

0.7371ex29223900452-Amino-3,5-dibromobenzaldehyde (CAS RN 50910-55-9) with a purity by weight of 98 % or more0 %-31.12.20240.3546ex2922430010Anthranilic acid (CAS RN 118-92-3)0 %-31.12.20240.3547ex2922498510Ornithine aspartate (INNM) (CAS RN 3230-94-2)0 %-31.12.20240.7853ex2922498513Benzyl glycinate–4-methylbenzene-1-sulfonic acid (1/1) (CAS RN 1738-76-7) with a purity by weight of 93 % or more0 %-31.12.20240.5037ex2922498517Glycine (CAS RN 56-40-6) with a purity by weight of 95 % or more, whether or not with not more than 5 % addition of anti-caking agent silicon dioxide (CAS RN 112926-00-8)0 %-31.12.20250.5619ex29224985203-Amino-4-chlorobenzoic acid (CAS RN 2840-28-0)0 %-31.12.20270.8162ex29224985232-Ethylhexyl 4-aminobenzoate (CAS RN 26218-04-2) with a purity by weight of 99 % or more0 %-31.12.20260.6340ex2922498525Dimethyl 2-aminobenzene-1,4-dicarboxylate (CAS RN 5372-81-6)0 %-31.12.20240.8234ex29224985334-Amino-2-chlorobenzoic acid (CAS RN 2457-76-3) with a purity by weight of 98 % or more0 %-31.12.20260.3544ex2922498540Norvaline0 %-31.12.20240.8236ex2922498543(E)-Ethyl 4-(dimethylamino)but-2-enoate maleate (CAS RN 1690340-79-4) with a purity by weight of 98 % or more0 %-31.12.20260.3983ex2922498550D-(-)-Dihydrophenylglycine (CAS RN 26774-88-9)0 %-31.12.20240.8340ex2922498553(S)-ethyl 3-amino-3-phenylpropanoate hemi((2R,3R)-2,3-dihydroxysuccinate) with a purity by weight of 98 % or more0 %-31.12.20270.4239ex2922498560Ethyl-4-dimethylaminobenzoate (CAS RN 10287-53-3)0 %-31.12.20270.6650ex2922498565Diethyl aminomalonate hydrochloride (CAS RN 13433-00-6)0 %-31.12.20250.4426ex29224985702-Ethylhexyl-4-dimethylaminobenzoate (CAS RN 21245-02-3)0 %-31.12.20240.7254ex2922498575L-alanine isopropyl ester hydrochloride (CAS RN 62062-65-1)0 %-31.12.20240.6100ex292249858012-Aminododecanoic acid (CAS RN 693-57-2)0 %-31.12.2024 0.7020ex29225000102-(2-(2-Aminoethoxy)ethoxy)acetic acid hydrochloride (CAS RN 134979-01-4)0 %-31.12.20260.7257ex29225000153,5-Diiodothyronine (CAS RN 1041-01-6)0 %-31.12.20270.4702ex29225000201-[2-Amino-1-(4-methoxyphenyl)-ethyl]-cyclohexanol hydrochloride (CAS RN 130198-05-9)0 %-31.12.20240.8445ex2922500025L-Threonine (CAS RN 72-19-5)0 %-31.12.20270.7523ex2922500035(2S)-2-Amino-3-(3,4-dimethoxyphenyl)-2-methylpropanoic acid hydrochloride (CAS RN 5486-79-3)0 %-31.12.20240.8473ex2922500045(S)-2-Amino-2-(3-fluoro-5-methoxyphenyl)ethanol hydrochloride (CAS RN 2095692-22-9) with a purity by weight of 98 % or more0 %-31.12.20270.8364ex29225000551-{[4-(Benzyloxy)phenyl]-2-(dimethylamino)ethyl}cyclohexanol (CAS RN 93413-61-7) with a purity by weight of 98 % or more0 %-31.12.20270.8325ex29225000654-[2-(Dimethylamino)ethoxy]phenylmethanone (CAS RN 173163-13-8) with a purity by weight of 98 % or more0 %-31.12.20270.2681ex29225000702-(1-Hydroxycyclohexyl)-2-(4-methoxyphenyl)ethylammonium acetate0 %-31.12.20240.6226ex2923100010Calcium phosphoryl choline chloride tetrahydrate (CAS RN 72556-74-2)0 %-31.12.20240.3543ex2923900010Tetramethylammonium hydroxide, in the form of an aqueous solution containing 25 % (± 0,5 %) by weight of tetramethylammonium hydroxide0 %-31.12.20240.4499ex2923900025Tetrakis(dimethylditetradecylammonium) molybdate (CAS RN 117342-25-3)0 %-31.12.20240.8159ex2923900030Tetrabutylammonium tetrahydroborate (CAS RN 33725-74-5) with a purity by weight of 97 % or more0 %-31.12.20260.7879ex2923900050Betaine hydrochloride (CAS RN 590-46-5), with a purity by weight of 93 % or more0 %-31.12.2024

0.7089ex2923900055Tetrabutylammonium bromide (CAS RN 1643-19-2)0 %-31.12.20260.7615ex2923900065N,N,N-Trimethyl-tricyclo[3.3.1.13,7]decan-1-aminium hydroxide (CAS RN 53075-09-5) in form of an aqueous solution with a content of N,N,N-trimethyl-tricyclo[3.3.1.13,7]decan-1-aminium hydroxide by weight of 17,5 % or more but not more than 27,5 %0 %-31.12.20240.3538ex2923900070 Tetrapropylammonium hydroxide, in the form of an aqueous solution containing: 40 % (± 2 %) by weight of tetrapropylammonium hydroxide, 0,3 % by weight or less of carbonate, 0,1 % by weight or less of tripropylamine, 500 mg/kg or less of bromide and 25 mg/kg or less of potassium and sodium taken together 0 %-31.12.20240.5063ex2923900075 Tetraethylammonium hydroxide, in the form of an aqueous solution containing: 35 % (± 0,5 %) by weight of tetraethylammonium hydroxide, not more than 1000 mg/kg of chloride, not more than 2 mg/kg of iron, and not more than 10 mg/kg of potassium 0 %-31.12.20250.3536ex2923900080Diallyldimethylammonium chloride (CAS RN 7398-69-8) , in the form of an aqueous solution containing by weight 63 % or more but not more than 67 % of diallyldimethylammonium chloride0 %-31.12.20240.6410ex2923900085N,N,N-Trimethylanilinium chloride (CAS RN 138-24-9)0 %-31.12.20240.2678ex29241900102-Acrylamido-2-methylpropanesulphonic acid (CAS RN 15214-89-8) or its sodium salt (CAS RN 5165-97-9), or its ammonium salt (CAS RN 58374-69-9)0 %-31.12.20240.8561ex2924190013N-(tert-Butoxycarbonyl)glycine (CAS RN 4530-20-5) with a purity by weight of 98 % or more0 %-31.12.20280.6227ex2924190015N-Ethyl N-methylcarbamoyl chloride (CAS RN 42252-34-6)0 %-31.12.20240.8000ex29241900182-(((Butylamino)carbonyl)oxy)ethyl acrylate (CAS RN 63225-53-6) with a purity by weight of 97 % or more0 %-31.12.2025 0.8027ex2924190028(2S)-2-Amino-5-(carbamoylamino)pentanoic acid ; 2-hydroxybutanedioic acid (2:1) (CAS RN 54940-97-5) with a purity by weight of 98 % or more0 %-31.12.20250.3535ex2924190030Methyl 2-acetamido-3-chloropropionate (CAS RN 87333-22-0)0 %-31.12.20240.8030ex2924190033(2S)-2-Amino-5-(carbamoylamino)pentanoic acid; 2-hydroxybutanedioic acid (1:1) (CAS RN 70796-17-7) with a purity by weight of 98,5 % or more0 %-31.12.20250.6549ex2924190035Acetamide (CAS RN 60-35-5)0 %-31.12.20240.8041ex2924190038Diethyl acetamidomalonate (CAS RN 1068-90-2) with a purity by weight of 98 % or more0 %-31.12.20250.8049ex2924190043N6-(tert-Butoxycarbonyl)-L-lysine methyl ester hydrochloride (CAS RN 2389-48-2) with a purity by weight of 98 % or more0 %-31.12.20250.8283ex2924190048N,N-Dimethylcarbamoyl chloride (CAS RN 79-44-7) with a purity by weight of 99 % or more0 %-31.12.20260.8429ex2924190053Aqueous solution of propamocarb hydrochloride (ISOM) (CAS RN 25606-41-1), containing by weight 64 % or more, but not more than 68 % of propamocarb hydrochloride0 %-31.12.20270.7060ex29241900552-Propynyl butylcarbamate (CAS RN 76114-73-3)0 %-31.12.20260.4160ex2924190060N,N-Dimethylacrylamide (CAS RN 2680-03-7)0 %-31.12.20260.7482ex29241900652,2,2-Trifluoroacetamide (CAS RN 354-38-1)0 %-31.12.20240.4380ex2924190070Methylcarbamate (CAS RN 598-55-0)0 %-31.12.20240.5605ex2924190080Tetrabutylurea (CAS RN 4559-86-8)0 %-31.12.20270.5998ex2924210020(3-Aminophenyl)urea hydrochloride (CAS RN 59690-88-9)0 %-31.12.20240.353329242500Alachlor (ISO) (CAS RN 15972-60-8)0 %-31.12.20240.6047ex29242970124-(Acetylamino)-2-aminobenzenesulphonic acid (CAS RN 88-64-2)0 %-31.12.20240.3534ex2924297015Acetochlor (ISO), (CAS RN 34256-82-1)0 %-31.12.2024

0.6266ex29242970172-(Trifluoromethyl)benzamide (CAS RN 360-64-5)0 %-31.12.20240.6363ex29242970192-[[2-(Benzyloxycarbonylamino)acetyl]amino]propionic acid (CAS RN 3079-63-8)0 %-31.12.20240.4685ex29242970202-Chloro-N-(2-ethyl-6-methylphenyl)-N-(propan-2-yloxymethyl)acetamide (CAS RN 86763-47-5)0 %-31.12.20240.6568ex2924297023Benalaxyl-M (ISO) (CAS RN 98243-83-5)0 %-31.12.20240.8153ex29242970252-[2-(Methoxycarbonyl-phenyl-amino)-phenyl]-acetic acid (CAS RN 353497-35-5) with a purity by weight of 98 % or more0 %-31.12.20260.7118ex2924297030Sodium 4-(4-methyl-3-nitrobenzoylamino)benzenesulphonate (CAS RN 84029-45-8)0 %-31.12.20260.8235ex2924297032N-(4-Amino-2-ethoxyphenyl)acetamide (CAS RN 848655-78-7) with a purity by weight of 98 % or more0 %-31.12.20260.8161ex2924297035N-(1,1-Dimethylethyl)-4-amino-benzamide (CAS RN 93483-71-7) with a purity by weight of 99 % or more0 %-31.12.20260.8258ex2924297036N,N’-(2-Chloro-5-methyl-1,4-phenylene)bis[3-oxobutyramide] (CAS RN 41131-65-1) with a purity by weight of 97 % or more0 %-31.12.20260.6110ex2924297037Beflubutamid (ISO) (CAS RN 113614-08-7)0 %-31.12.20240.8595ex29242970382-Methyl-2-propanyl{(2S,3R)-3-hydroxy-4-[(2-methylpropyl)amino]-1-phenyl-2- butanyl}carbamate (CAS RN 160232-08-6) with a purity by weight of 97 % or more0 %-31.12.20280.5066ex2924297040N,N’–1,4-Phenylenebis[3-oxobutyramide], (CAS RN 24731-73-5)0 %-31.12.20250.5127ex2924297045Propoxur (ISO) (CAS RN 114-26-1)0 %-31.12.20250.8183ex2924297046S-Metolachlor (ISO) (CAS RN 87392-12-9) with a purity by weight of 98 % or more0 %-31.12.20260.7841ex2924297047(S)-tert-Butyl (1-amino-3-(4-iodophenyl)-1-oxopropan-2-yl)carbamate (CAS RN 868694-44-4) with a purity by weight of 95 % or more0 %-31.12.2024 0.8381ex2924297048(3R)-N-(tert-butoxycarbonyl)-3-amino-4-(2,4,5-trifluorophenyl)butanoic acid (CAS RN 486460-00-8) with a purity by weight of 97 % or more0 %-31.12.20270.8346ex2924297049tert-Butyl [(1R,2S,5S)-2-amino-5-(dimethylcarbamoyl)cyclohexyl]carbamate ethanedioate (CAS RN 1210348-34-7) with a purity by weight of 95 % or more0 %-31.12.20270.8184ex2924297052Zoxamide (ISO) (CAS RN 156052-68-5) with a purity by weight of 97 % or more0 %-31.12.20260.5622ex29242970534-Amino-N-[4-(aminocarbonyl)phenyl]benzamide (CAS RN 74441-06-8)0 %-31.12.20270.8362ex29242970542-[4-(Benzyloxy)phenyl]-N,N-dimethylacetamide (CAS RN 919475-15-3) with a purity by weight of 98 % or more0 %-31.12.20270.5069ex2924297055N,N’-(2,5-Dimethyl–1,4-phenylene)bis[3-oxobutyramide] (CAS RN 24304-50-5)0 %-31.12.20250.8315ex2924297056Valifenalate (ISO) (CAS RN 283159-90-0) with a purity by weight of 98 % or more0 %-31.12.20270.8043ex29242970582-Chloro-N-[1-(4-chloro-3-fluorophenyl)-2-methylpropan-2-yl]acetamide (CAS RN 787585-35-7) with a purity by weight of 98 % or more0 %-31.12.20250.6767ex29242970622-Chlorobenzamide (CAS RN 609-66-5)0 %-31.12.20250.6766ex2924297064N-(3’,4’-dichloro-5-fluoro[1,1’-biphenyl]-2-yl)acetamide (CAS RN 877179-03-8)0 %-31.12.20250.7632ex2924297067N,N’-(2,5-Dichloro–1,4-phenylene)bis[3-oxobutyramide] (CAS RN 42487-09-2)0 %-31.12.20240.7582ex2924297070N-[(benzyloxy)carbonyl]glycyl-N-[(2S)-1-{4-[(tert-butoxycarbonyl)oxy]phenyl}-3-hydroxypropan-2-yl]-L-alaninamide0 %-31.12.20240.6480ex2924297073Napropamide (ISO) (CAS RN 15299-99-7)0 %-31.12.20240.2672ex29242970753-Amino-p-anisanilide (CAS RN 120-35-4)0 %-31.12.20240.8060ex29242970785-Amino-3-(4-chlorophenyl)-5-oxopentanoic acid (CAS RN 1141-23-7) with a purity by weight of 98 % or more0 %-31.12.2025

0.2673ex2924297085p-Aminobenzamide (CAS RN 2835-68-9)0 %-31.12.20240.4495ex29242970885’-Chloro-3-hydroxy-2’-methyl-2-naphthanilide (CAS RN 135-63-7)0 %-31.12.20240.4493ex2924297089Flutolanil (ISO) (CAS RN 66332-96-5)0 %-31.12.20240.3690ex29242970913-Hydroxy-2’-methoxy-2-naphthanilide (CAS RN 135-62-6)0 %-31.12.20240.3691ex29242970923-Hydroxy-2-naphthanilide (CAS RN 92-77-3)0 %-31.12.20240.3692ex29242970933-Hydroxy-2’-methyl-2-naphthanilide (CAS RN 135-61-5)0 %-31.12.20240.3693ex29242970942’-Ethoxy-3-hydroxy-2-naphthanilide (CAS RN 92-74-0)0 %-31.12.20240.3863ex29242970971,1-Cyclohexanediacetic acid monoamide (CAS RN 99189-60-3)0 %-31.12.20240.3526ex2925110020Saccharin and its sodium salt0 %-31.12.20240.2674ex2925199510N-Phenylmaleimide (CAS RN 941-69-5)0 %-31.12.20240.5612ex29251995204,5,6,7-Tetrahydroisoindole-1,3-dione (CAS RN 4720-86-9)0 %-31.12.20270.5740ex2925199530N,N’-(m-Phenylene)dimaleimide (CAS RN 3006-93-7)0 %-31.12.20270.8013ex2925199540N-Iodosuccinimide (CAS RN 516-12-1) with a purity by weight of 98,5 % or more0 %-31.12.20250.2934ex2925290010Dicyclohexylcarbodiimide (CAS RN 538-75-0)0 %-31.12.20240.5891ex2925290020N-[3-(Dimethylamino)propyl]-N’-ethylcarbodiimide hydrochloride (CAS RN 25952-53-8)0 %-31.12.20240.8339ex29252900251-(3-(2-Hydroxyethyl)phenyl)guanidinium methanesulfonate (CAS RN 2101429-50-7) with a purity by weight of 99 % or more0 %-31.12.20270.7749ex2925290040N-Amidinosarcosine (CAS RN 57-00-1)0 %-31.12.20240.7832ex2925290050(Chloromethylene)dimethyliminium chloride (CAS RN 3724-43-4) with a purity by weight of 95 % or more0 %-31.12.20240.8033ex2925290060Formamidine acetate (CAS RN 3473-63-0) with a purity by weight of 99 % or more0 %-31.12.2025 0.8040ex2925290070Bromomethylidene(dimethyl)azanium bromide (CAS RN 24774-61-6) with a purity by weight of 97 % or more0 %-31.12.20250.6258ex29269070164-Cyano-2-nitrobenzoic acid methyl ester (CAS RN 52449-76-0)0 %-31.12.20240.6934ex2926907017Cypermethrin (ISO) with its stereoisomers (CAS RN 52315-07-8) with a purity by weight of 90 % or more0 %-31.12.20250.7408ex2926907018Flumethrin (ISO) (CAS RN 69770-45-2)0 %-31.12.20270.7466ex29269070192-(4-Amino-2-chloro-5-methylphenyl)-2-(4-chlorophenyl) acetonitrile (CAS RN 61437-85-2)0 %-31.12.20240.2668ex29269070202-(m-Benzoylphenyl)propiononitrile (CAS RN 42872-30-0)0 %-31.12.20240.7458ex29269070214-Bromo-2-chlorobenzonitrile (CAS RN 154607-01-9)0 %-31.12.20240.7514ex2926907022Acetonitrile (CAS RN 75-05-8)0 %-31.12.20240.6109ex2926907023Acrinathrin (ISO) (CAS RN 101007-06-1)0 %-31.12.20240.7805ex29269070242-Hydroxy-2-methylpropiononitrile (CAS RN 75-86-5) with a purity by weight of 99 % or more0 %-31.12.20240.5227ex29269070252,2-Dibromo-3-nitrilopropionamide (CAS RN 10222-01-2)0 %-31.12.20260.6259ex2926907026Cyfluthrin (ISO) (CAS RN 68359-37-5) with a purity by weight of 95,5 % or more for the use in the manufacture of biocidal products0 %-31.12.20240.6149ex2926907027Cyhalofop-butyl (ISO) (CAS RN 122008-85-9)0 %-31.12.20240.8321ex29269070283-Bromo-6-chloro-2-fluorobenzonitrile (CAS RN 943830-79-3) with a purity by weight of 98 % or more0 %-31.12.20270.7430ex29269070292-Cyclohexylidene-2-phenylacetonitrile (CAS RN 10461-98-0) with a purity by weight of 95 % or more0 %-31.12.20270.7201ex29269070304,5-Dichloro-3,6-dioxocyclohexa-1,4-diene-1,2-dicarbonitrile (CAS RN 84-58-2)0 %-31.12.20260.8462ex2926907031Lambda-cyhalothrin (ISO) (CAS RN 91465-08-6) with a purity by weight of 97 % or more0 %-31.12.2027

0.7406ex2926907033Deltamethrin (ISO) (CAS RN 52918-63-5)0 %-31.12.20270.7034ex29269070354-Cyano-2-methoxybenzaldehyde (CAS RN 21962-45-8)0 %-31.12.20260.6970ex29269070402-(4-Cyanophenylamino)acetic acid (CAS RN 42288-26-6)0 %-31.12.20240.3522ex2926907050Alkyl or alkoxyalkyl esters of cyanoacetic acid0 %-31.12.20240.8217ex2926907056Methyl 2-cyano-2-propylpentanoate (CAS RN 66546-92-7) with a purity by weight of 97 % or more0 %-31.12.20260.4182ex2926907061m-(1-Cyanoethyl)benzoic acid (CAS RN 5537-71-3)0 %-31.12.20260.4644ex2926907064Esfenvalerate (CAS RN 66230-04-4) of a purity by weight of 83 % or more in a mixture of its own isomers0 %-31.12.20240.4802ex2926907070Methacrylonitrile (CAS RN 126-98-7)0 %-31.12.20240.2543ex2926907074Chlorothalonil (ISO) (CAS RN 1897-45-6)0 %-31.12.20240.3521ex2926907075Ethyl 2-cyano-2-ethyl-3-methylhexanoate (CAS RN 100453-11-0)0 %-31.12.20240.3516ex2926907080Ethyl 2-cyano-2-phenylbutyrate (CAS RN 718-71-8)0 %-31.12.20240.3514ex2926907086Ethylenediaminetetraacetonitrile (CAS RN 5766-67-6)0 %-31.12.20240.3515ex2926907089Butyronitrile (CAS RN 109-74-0)0 %-31.12.20240.2667ex29270000102,2’-Dimethyl–2,2’-azodipropionamidine dihydrochloride0 %-31.12.20240.2665ex29270000204-Anilino-2-methoxybenzenediazonium hydrogen sulphate (CAS RN 36305-05-2)0 %-31.12.20240.7337ex29270000252,2’-Azobis(4-methoxy–2,4-dimethylvaleronitrile) (CAS RN 15545-97-8)0 %-31.12.20270.2810ex29270000304’-Aminoazobenzene-4-sulphonic acid (CAS RN 104-23-4)0 %-31.12.20240.6306ex2927000035C.C’-Azodi(formamide) (CAS RN 123-77-3) in the form of yellow powder with a decomposition temperature of 180°C or more but not more than 220°C used as a foaming agent in the manufacture of thermoplastic resins, elastomer and cross-linked polythene foam0 %-31.12.2024 0.3984ex29270000604,4’-Dicyano–4,4’-azodivaleric acid (CAS RN 2638-94-0)0 %-31.12.20240.2661ex29280090103,3’-Bis(3,5-di-tert-butyl-4-hydroxyphenyl)-N,N’-bipropionamide (CAS RN 32687-78-8)0 %-31.12.20240.6479ex2928009013Cymoxanil (ISO) (CAS RN 57966-95-7)0 %-31.12.20240.6548ex2928009018Acetone oxime (CAS RN 127-06-0) of a purity by weight of 99 % or more0 %-31.12.20240.6871ex2928009023Metobromuron (ISO) (CAS RN 3060-89-7) with a purity by weight of 98 % or more0 %-31.12.20250.4929ex2928009025Acetaldehyde oxime (CAS RN 107-29-9) in an aqueous solution0 %-31.12.20250.6985ex2928009028Pentan-2-one oxime (CAS RN 623-40-5)0 %-31.12.20260.5438ex2928009030N-Isopropylhydroxylamine (CAS RN 5080-22-8)0 %-31.12.20260.7448ex29280090334-Chlorophenylhydrazine Hydrochloride (CAS RN 1073-70-7)0 %-31.12.20240.8061ex2928009038 Aqueous solution of methoxyammonium chloride (CAS RN 593-56-6), containing by weight: 30 % or more but not more than 40 % of methoxyammonium chloride not more than 4 % of hydrochloric acid 0 %-31.12.20250.2659ex2928009040O-Ethylhydroxylamine, in the form of an aqueous solution (CAS RN 624-86-2)0 %-31.12.20240.8093ex29280090432-(3-Methoxy-3-oxopropyl)-1,1,1-trimethylhydrazinium bromide (CAS RN 106966-25-0) with a purity by weight of 99 % or more0 %-31.12.20250.5919ex2928009045Tebufenozide (ISO) (CAS RN 112410-23-8)0 %-31.12.20240.8158ex29280090481-{[(1H-Fluoren-9-ylmetoxi)carbonil]oxi}pyrrolidine-2,5-dione (CAS RN 82911-69-1) with a purity by weight of 98 % or more0 %-31.12.20260.6635ex2928009050Aqueous solution of 2,2’-(hydroxyimino) bisethanesulphonic acid disodium salt (CAS RN 133986-51-3) with a content by weight of more than 33,5 % but not more than 36,5 %0 %-31.12.2025

0.8474ex2928009053Ethyl chloro[(4-methoxyphenyl)hydrazono]acetate (CAS RN 27143-07-3) with a purity by weight of 98 % or more0 %-31.12.20270.5918ex2928009055Aminoguanidinium hydrogen carbonate (CAS RN 2582-30-1)0 %-31.12.20240.6364ex29280090652-Amino-3-(4-hydroxyphenyl) propanal semicarbazone hydrochloride0 %-31.12.20240.4544ex2928009070Butanone oxime (CAS RN 96-29-7)0 %-31.12.20240.5228ex2928009075Metaflumizone (ISO) (CAS RN 139968-49-3)0 %-31.12.20260.3510ex2928009080Cyflufenamid (ISO) (CAS RN 180409-60-3)0 %-31.12.20240.4714ex29291000153,3’-Dimethylbiphenyl–4,4’-diyl diisocyanate (CAS RN 91-97-4)0 %-31.12.20240.5827ex2929100020Butyl isocyanate (CAS RN 111-36-4)0 %-31.12.20270.4188ex29291000351,3-Bis(isocyanatomethyl)benzene (CAS RN 3634-83-1) with a purity by weight of 99 % or more0 %-31.12.20240.2660ex2929100040m-Isopropenyl-α,α-dimethylbenzyl isocyanate (CAS RN 2094-99-7)0 %-31.12.20240.5033ex29291000452,5 (and 2,6)-Bis(isocyanatomethyl)bicyclo[2.2.1]heptane (CAS RN 74091-64-8) with a purity by weight of 99 % or more0 %-31.12.20240.2657ex2929100050m-Phenylenediisopropylidene diisocyanate (CAS RN 2778-42-9)0 %-31.12.20240.3509ex2929100060Trimethylhexamethylene diisocyanate, mixed isomers0 %-31.12.20240.8451ex2929100065Ethyl isocyanate (CAS RN 109-90-0) with a purity by weight of 98 % or more0 %-31.12.20270.8171ex2929900040N-Butylphosphorothioic triamide (CAS RN 94317-64-3) with a purity by weight of 97 % or more0 %-31.12.20260.8172ex2929900050N-Propylphosphorothioic triamide (CAS RN 916809-14-8) with a purity by weight of 97 % or more0 %-31.12.20260.4298ex2930200040Prosulfocarb (ISO) (CAS RN 52888-80-9) with purity by weight of 97 % or more0 %-31.12.2027 0.5278ex29302000502-Isopropylethylthiocarbamate (CAS RN 141-98-0) with a purity by weight of 95 % or more0 %-31.12.20240.8036ex2930909811Benzyl (2S)-2-amino-3-[3-(methanesulphonylphenyl)]propanoate hydrochloride (CAS RN 1194550-59-8) with a purity by weight of 98 % or more0 %-31.12.20250.7483ex29309098124,4’-Sulfonyldiphenol (CAS RN 80-09-1) used in the manufacture of polyarylsulfones or polyarylethersulfones0 %-31.12.20240.8047ex2930909814(E)-N’-(2-Cyano-4-(3-(1-hydroxy-2-methylpropan-2-yl)thioureido)phenyl)-N,N-dimethyl-formimidamide (CAS RN 1429755-57-6) with a purity by weight of 98 % or more0 %-31.12.20250.2932ex2930909815Ethoprophos (ISO) (CAS RN 13194-48-4)0 %-31.12.20240.6551ex29309098163-(Dimethoxymethylsilyl)-1-propanethiol (CAS RN 31001-77-1)0 %-31.12.20240.5999ex29309098172-(3-Aminophenylsulphonyl)ethyl hydrogen sulphate (CAS RN 2494-88-4)0 %-31.12.20240.7748ex2930909818Dimethyl sulfone (CAS RN 67-71-0)0 %-31.12.20240.8050ex29309098194-Amino-5-(ethanesulphonyl)-2-methoxybenzoic acid (CAS RN 71675-87-1) with a purity by weight of 98 % or more0 %-31.12.20250.7799ex29309098204-(4-Methylphenylthio)benzophenone (CAS RN 83846-85-9)0 %-31.12.20240.6750ex2930909821[2,2’-Thio-bis(4-tert-octylphenolato)]-n-butylamine nickel (CAS RN 14516-71-3)0 %-31.12.20260.6769ex2930909822Tembotrione (ISO) (CAS RN 335104-84-2) with a purity by weight of 94,5 % or more0 %-31.12.20250.5899ex2930909823Dimethyl [(methylsulphanyl)methylylidene]biscarbamate (CAS RN 34840-23-8)0 %-31.12.20240.7714ex2930909824Phenyl vinyl sulfone (CAS RN 5535-48-8)0 %-31.12.20240.2930ex2930909825Thiophanate-methyl (ISO) (CAS RN 23564-05-8)0 %-31.12.20240.6873ex2930909826Folpet (ISO) (CAS RN 133-07-3) with a purity by weight of 97,5 % or more0 %-31.12.2025

0.6585ex29309098272-[(4-Amino-3-methoxyphenyl)sulphonyl]ethyl hydrogen sulphate (CAS RN 26672-22-0)0 %-31.12.20240.8069ex2930909828 Mesotrione (ISO) (CAS RN 104206-82-8) in form of wet cake or wet paste or in its crystalline form, with a purity of 74 % or more by weight and, a maximum water content of 23 % by weight 0 %-31.12.20250.7859ex29309098294-Amino-5-(ethylsulfanyl)-2-methoxybenzoic acid (CAS RN 71675-86-0) with a purity by weight of 98 % or more0 %-31.12.20240.2933ex29309098304-(4-Isopropoxyphenylsulphonyl)phenol (CAS RN 95235-30-6)0 %-31.12.20240.7833ex2930909831(p-Toluenesulphonyl)methyl isocyanide (CAS RN 36635-61-7) with a purity by weight of 98 % or more0 %-31.12.20240.8152ex29309098322-Methoxy-N-[2-nitro-5-(phenylsulfanyl)phenyl]acetamide (CAS RN 63470-85-9) with a purity by weight of 96 % or more0 %-31.12.20260.6584ex29309098332-Amino-5-{[2-(sulfooxy)ethyl]sulfonyl}benzenesulfonIc acid (CAS RN 42986-22-1)0 %-31.12.20240.5035ex29309098342,3-Bis((2-mercaptoethyl)thio)-1-propanethiol (CAS RN 131538-00-6) with a purity by weight of 85 % or more, but not more than 95 %0 %-31.12.20240.3811ex2930909835Glutathione (CAS RN 70-18-8)0 %-31.12.20260.8510ex2930909836Anhydrous potassium O-isopentyl-dithiocarbonate (CAS RN 928-70-1) with a purity by weight of 90 % or more0 %-31.12.20270.7682ex2930909838Allyl isothiocyanate (CAS RN 57-06-7)0 %-31.12.20240.8447ex2930909839Thiodiacetic acid (CAS RN 123-93-3) with a purity by weight of 98 % or more0 %-31.12.20270.2928ex29309098403,3’-Thiodi(propionic acid) (CAS RN 111-17-1)0 %-31.12.20240.8481ex29309098412,2’-Diallyl-4,4’-sulphonyldiphenol (CAS RN 41481-66-7) with a purity by weight of 96 % or more0 %-31.12.20270.6167ex2930909843Trimethylsulfoxonium iodide (CAS RN 1774-47-6)0 %-31.12.2024 0.2931ex29309098452-[(p-Aminophenyl)sulphonyl]ethyl hydrogen sulphate (CAS RN 2494-89-5)0 %-31.12.20240.7689ex29309098503-Mercaptopropionic acid (CAS RN 107-96-0)0 %-31.12.20240.6617ex2930909853Bis(4-chlorophenyl) sulphone (CAS RN 80-07-9)0 %-31.12.20250.5114ex2930909855Thiourea (CAS RN 62-56-6)0 %-31.12.20250.2929ex2930909860Methyl phenyl sulphide (CAS RN 100-68-5)0 %-31.12.20240.4629ex29309098643-Chloro-2-methylphenyl methyl sulphide (CAS RN 82961-52-2)0 %-31.12.20240.4296ex2930909868Clethodim (ISO) (CAS RN 99129-21-2)0 %-31.12.20270.3986ex29309098774-[4-(2-Propenyloxy)phenylsulphonyl]phenol (CAS RN 97042-18-7)0 %-31.12.20240.4187ex29309098784-Mercaptomethyl-3,6-dithia-1,8-octanedithiol (CAS RN 131538-00-6)0 %-31.12.20260.2999ex2930909880Captan (ISO) (CAS RN 133-06-2)0 %-31.12.20240.4694ex2930909881Disodium hexamethylene-1,6-bisthiosulfate dihydrate (CAS RN 5719-73-3)3 %-31.12.20240.7985ex29309098881-{4-[(4-Benzoylphenyl)sulphanyl]phenyl}-2-methyl-2-[(4-methylphenyl)sulphonyl]propan-1-one (CAS RN 272460-97-6) with a purity by weight of 94 % or more0 %-31.12.20250.4094ex2930909889Potassium- or sodium-salt of O-ethyl-, O-isopropyl-, O-butyl-, O-isobutyl- or O-pentyl-dithiocarbonates0 %-31.12.20260.7070ex29309098931-Hydrazino-3-(methylthio)propan-2-ol (CAS RN 14359-97-8)0 %-31.12.20260.7078ex2930909895N-(Cyclohexylthio)phthalimide (CAS RN 17796-82-6)0 %-31.12.20260.7086ex2930909897Diphenyl sulphone (CAS RN 127-63-9)0 %-31.12.20260.5741ex2931499008Sodium diisobutyldithiophosphinate (CAS RN 13360-78-6) in an aqueous solution0 %-31.12.20270.8546ex2931499010Triethyl phosphonoacetate (CAS RN 867-13-0) with a purity by weight of 98 % or more0 %-31.12.2028

0.5492ex2931499013Trioctylphosphine oxide (CAS RN 78-50-2)0 %-31.12.20260.6088ex2931499023Di-tert-butylphosphane (CAS RN 819-19-2)0 %-31.12.20240.5758ex2931499025(Z)-Prop-1-en-1-ylphosphonic acid (CAS RN 25383-06-6)0 %-31.12.20270.3497ex2931499030Bis(2,4,4-trimethylpentyl)phosphinic acid (CAS RN 83411-71-6)0 %-31.12.20240.7533ex2931499035Ethyl phenyl(2,4,6-trimethylbenzoyl)phosphinate (CAS RN 84434-11-7)0 %-31.12.20240.2656ex2931499038N-(Phosphonomethyl)iminodiacetic acid (CAS RN 5994-61-6) containing by weight not more than 15 % of water, and with a dry weight purity of 97 % or more0 %-31.12.20240.5229ex2931499040Tetrakis(hydroxymethyl)phosphonium chloride (CAS RN 124-64-1)0 %-31.12.20260.3492ex2931499048Tetrabutylphosphonium acetate in the form of an aqueous solution (CAS RN 30345-49-4)0 %-31.12.20240.3987ex29314990553-(Hydroxyphenylphosphinoyl)propionic acid (CAS RN 14657-64-8)0 %-31.12.20240.7709ex29315990502-Chloroethylphosphonic acid (CAS RN 16672-87-0) solid or in aqueous solution, with a content by weight of 2-Chloroethylphosphonic acid of 65 % or more0 %-31.12.20240.3504ex2931900003Butylethylmagnesium (CAS RN 62202-86-2), in the form of a solution in heptane0 %-31.12.20240.4515ex2931900015Methylcyclopentadienyl manganese tricarbonyl (CAS RN 12108-13-3) containing not more than 4,9 % by weight of cyclopentadienyl manganese tricarbonyl0 %-31.12.20240.8051ex2931900023Ixazomib citrate (INNM) (CAS RN 1239908-20-3) with a purity by weight of 95 % or more0 %-31.12.20250.7951ex2931900025N-(3-(Dimethoxymethylsilyl)propyl)ethylenediamine (CAS RN 3069-29-2) with a purity by weight of 98 % or more0 %-31.12.20250.8063ex2931900028Triethoxy(3-isocyanatopropyl)silane (CAS RN 24801-88-5) with a purity by weight of 96 % or more0 %-31.12.2025 0.8272ex2931900030Tert-Butylchlorodimethylsilane (CAS RN 18162-48-6) with a purity by weight of 99 % or more0 %-31.12.20260.3499ex2931900033Dimethyl[dimethylsilyldiindenyl]hafnium (CAS RN 220492-55-7)0 %-31.12.20240.2654ex2931900035N,N-Dimethylanilinium tetrakis(pentafluorophenyl)borate (CAS RN 118612-00-3)0 %-31.12.20240.8316ex29319000382-(Trimethylsilyl)ethoxymethyl chloride (CAS RN 76513-69-4) with a purity by weight of 98 % or more0 %-31.12.20270.8442ex2931900040Chlorotrimethylsilane (CAS RN 75-77-4) with a purity by weight of 98 % or more0 %-31.12.20270.4121ex2931900050Trimethylsilane (CAS RN 993-07-7)0 %-31.12.20260.8554ex29319000553-(Hydroxymethyl)phenylboronic acid (CAS RN 87199-15-3) with a purity by weight of 95 % or more0 %-31.12.20280.3486ex2932130010Tetrahydrofurfuryl alcohol (CAS RN 97-99-4)0 %-31.12.20240.4590ex29321400101,6-Dichloro-1,6-dideoxy-β-D-fructofuranosyl-4-chloro-4-deoxy-α-D-galactopyranoside (CAS RN 56038-13-2)0 %-31.12.20240.3488ex2932190040Furan (CAS RN 110-00-9) of a purity by weight of 99 % or more0 %-31.12.20240.4514ex29321900412,2 Di(tetrahydrofuryl)propane (CAS RN 89686-69-1)0 %-31.12.20240.8252ex2932190055(3S)-3-[4-[(5-Bromo-2-chlorophenyl)methyl]phenoxy]tetrahydro-furan (CAS RN 915095-89-5) with a purity by weight of 97 % or more0 %-31.12.20260.7614ex2932190065Tefuryltrione (ISO) (CAS RN 473278-76-1)0 %-31.12.20240.3487ex2932190070Furfurylamine (CAS RN 617-89-0)0 %-31.12.20240.3611ex2932190075Tetrahydro-2-methylfuran (CAS RN 96-47-9)0 %-31.12.20240.5240ex29321900805-Nitrofurfurylidene di(acetate) (CAS RN 92-55-7)0 %-31.12.20260.2775ex29322090102’-Anilino-6’-[ethyl(isopentyl)amino]-3’-methylspiro[isobenzofuran-1(3H),9’-xanthen]-3-one (CAS RN 70516-41-5)0 %-31.12.20240.5257ex2932209015Coumarin (CAS RN 91-64-5)0 %-31.12.2026

0.7958ex29322090184-Hydroxycoumarin (CAS-RN 1076-38-6) with a purity by weight of 98 % or more0 %-31.12.20250.7984ex29322090231,4-Dioxane-2,5-dione (CAS RN 502-97-6) with a purity by weight of 99,5 % or more0 %-31.12.20250.8478ex2932209028(R)-3-(3,4-difluoro-2-methoxyphenyl)-4,5-dimethyl-5-(trifluoromethyl)furan-2(5H)-one (CAS RN 2875066-35-4) with a purity by weight of 98 % or more0 %-31.12.20270.8532ex29322090336-Cyclohexyl-4-methyl-2H-pyran-2-one (CAS RN 14818-35-0) with a purity of 99 % by weight or more0 %-31.12.20280.5611ex2932209040(S)-(–)-α-Amino-γ-butyrolactone hydrobromide (CAS RN 15295-77-9)0 %-31.12.20270.6094ex29322090452,2-Dimethyl-1,3-dioxane-4,6-dione (CAS RN 2033-24-1)0 %-31.12.20240.7283ex2932209050L-Lactide (CAS RN 4511-42-6), D-lactide (CAS RN 13076-17-0), dilactide (CAS RN 95-96-5) or meso-lactide (CAS RN 13076-19-2), each with a purity by weight of 90 % or more0 %-31.12.20270.7838ex2932209053(R)-4-Propyldihydrofuran-2(3H)-one (CAS RN 63095-51-2) with a purity by weight of 98 % or more0 %-31.12.20240.2765ex29322090556-Dimethylamino-3,3-bis(4-dimethylaminophenyl)phthalide (CAS RN 1552-42-7)0 %-31.12.20240.4162ex29322090606’-(Diethylamino)-3’-methyl-2’-(phenylamino)-spiro[isobenzofuran-1(3H),9’-[9H]xanthen]-3-one (CAS RN 29512-49-0)0 %-31.12.20260.7812ex2932209063Selamectin (INN) 5Z-isomer (CAS RN 220119-17-5)0 %-31.12.20240.6620ex2932209065Sodium 4-(methoxycarbonyl)-5-oxo-2,5-dihydrofuran-3-olate (CAS RN 1134960-41-0)0 %-31.12.20250.4161ex29322090716’-(Dibutylamino)-3’-methyl-2’-(phenylamino)-spiro[isobenzofuran-1(3H),9’-[9H]xanthen]-3-one (CAS RN 89331-94-2)0 %-31.12.20260.7599ex29322090753-Acetyl-6-methyl-2H-pyran-2, 4(3H)-dione (CAS RN 520-45-6)0 %-31.12.20240.3990ex2932209080Gibberellic acid with a minimum purity by weight of 88 % (CAS RN 77-06-5)0 %-31.12.2024 0.4403ex2932209084Decahydro-3a,6,6,9a-tetramethylnaphth [2,1-b] furan-2 (1H)-one (CAS RN 564-20-5)0 %-31.12.20240.8528ex29329900033,4-Dihydro-2-methoxy-2H-pyran (CAS RN 4454-05-1) with a purity by weight of 99 % or more0 %-31.12.20280.3610ex2932990010Bendiocarb (ISO) (CAS RN 22781-23-3)0 %-31.12.20240.7202ex2932990013(4-Chloro-3-(4-ethoxybenzyl)phenyl)((3aS,5R,6S,6aS)-6-hydroxy 2,2-dimethyltetrahydrofuro[2,3-d][1 ,3]dioxol-5-yl)methanone (CAS RN 1103738-30-2)0 %-31.12.20260.5269ex29329900151,3,4,6,7,8-Hexahydro-4,6,6,7,8,8-hexamethylindeno[5,6-c]pyran (CAS RN 1222-05-5)0 %-31.12.20260.7178ex29329900184-(4-Bromo-3-((tetrahydro-2H-pyran-2-yloxy)methyl)phenoxy)benzonitrile (CAS RN 943311-78-2)0 %-31.12.20260.7431ex29329900232-Ethyl-3-hydroxy-4-pyrone (CAS RN 4940-11-8)0 %-31.12.20270.5759ex29329900251-(2,2-Difluorobenzo[d][1,3]dioxol-5-yl)cyclopropanecarboxylic acid (CAS RN 862574-88-7)0 %-31.12.20270.7639ex2932990027(2-Butyl-3-benzofuranyl)(4-hydroxy-3,5-diiodophenyl)methanone (CAS RN 1951-26-4) with a purity by weight of 99 % or more0 %-31.12.20240.8257ex29329900281,4,7,10,13-Pentaoxacyclopentadecane (CAS RN 33100-27-5) with a purity by weight of 90 % or more, the remainder mainly consisting of lineair precursors0 %-31.12.20260.7535ex29329900333-Hydroxy-2-methyl-4-pyrone (CAS RN 118-71-8)0 %-31.12.20240.8035ex29329900381-Benzofuran-6-carboxylic acid (CAS RN 77095-51-3) with a purity by weight of 98 % or more0 %-31.12.20250.6243ex2932990043Ethofumesate (ISO) (CAS RN 26225-79-6) with a purity by weight of 97 % or more0 %-31.12.20240.5915ex29329900452-Butylbenzofuran (CAS RN 4265-27-4)0 %-31.12.20240.7766ex293299004712H-[1]Benzofuro[3,2-c][1]benzoxepin-6-one (CAS RN 28763-77-1)0 %-31.12.2024

0.8384ex2932990048(20R,25R)-spirost-5-en-3β-ol (CAS RN 512-04-9) with a purity by weight of 95 % or more0 %-31.12.20270.4907ex29329900507-Methyl-3,4-dihydro-2H-1,5-benzodioxepin-3-one (CAS RN 28940-11-6)0 %-31.12.20240.4063ex29329900513-(3,4-Methylenedioxyphenyl)-2-methylpropanal (CAS RN 1205-17-0) with a purity by weight of 98 % or more0 %-31.12.20270.6113ex29329900531,3-Dihydro-1,3-dimethoxyisobenzofurane (CAS RN 24388-70-3)0 %-31.12.20240.6771ex29329900654,4-Dimethyl-3,5,8-trioxabicyclo[5,1,0]octane (CAS RN 57280-22-5)0 %-31.12.20250.7978ex29329900683,9-Diethylidene-2,4,8,10-tetraoxaspiro[5.5]undecane (CAS RN 65967-52-4) with a purity by weight of 98 % or more0 %-31.12.20250.7930ex29329900735-Fluoro-3-methylbenzofuran-2-carboxylic acid (CAS RN 81718-76-5) with a purity by weight of 97 % or more0 %-31.12.20250.7936ex2932990078Methyl 2,2-difluoro-1,3-benzodioxole-5-carboxylate (CAS RN 773873-95-3) with a purity by weight of 98 % or more0 %-31.12.20250.4106ex29329900801,3:2,4-bis-O-(4-Methylbenzylidene)-D-glucitol (CAS RN 81541-12-0)0 %-31.12.20240.7954ex29329900836,11-Dihydrodibenz[b,e]oxepin-11-one (CAS RN 4504-87-4) with a purity by weight of 98 % or more0 %-31.12.20250.3697ex29329900851,3:2,4-bis-O-(3,4-Dimethylbenzylidene)-D-glucitol (CAS RN 135861-56-2)0 %-31.12.20240.7903ex29331990133-(Difluoromethyl)-5-fluoro-1-methyl-1H-pyrazole-4-carbonyl fluoride (CAS RN 1255735-07-9) with a purity by weight of 95 % or more0 %-31.12.20240.6262ex2933199015Pyrasulfotole (ISO) (CAS RN 365400-11-9) with a purity by weight of 96 % or more0 %-31.12.20240.7835ex29331990171,3-Dimethyl-1H-pyrazole (CAS RN 694-48-4) with a purity by weight of 98 % or more0 %-31.12.2024 0.7918ex2933199023Fluindapyr (ISO) (CAS RN 1383809-87-7) with a purity by weight of 96 % or more0 %-31.12.20240.6261ex29331990253-Difluoromethyl-1-methyl-1H-pyrazole-4-carboxylic acid (CAS RN 176969-34-9)0 %-31.12.20240.7836ex29331990273-(3,3,3-Trifluoro-2,2-dimethylpropoxy)-1H-pyrazole-4-carboxylic acid (CAS RN 2229861-20-3) with a purity by weight of 95 % or more0 %-31.12.20240.3699ex29331990303-Methyl-1-p-tolyl-5-pyrazolone (CAS RN 86-92-0)0 %-31.12.20240.7811ex2933199033Fipronil (ISO) (CAS RN 120068-37-3) with a purity by weight of 95 % or more for the use in the manufacture of veterinary medicine0 %-31.12.20240.8353ex29331990384,5-Dimethyl-1H-pyrazole-3-carboxylic acid (CAS RN 89831-40-3) with a purity by weight of 98 % or more0 %-31.12.20270.3877ex2933199040Edaravone (INN) (CAS RN 89-25-8)0 %-31.12.20240.7938ex2933199043tert-Butyl 2-(3,5-dimethyl-1H-pyrazol-4-yl)acetate (CAS RN 1082827-81-3) with a purity by weight of 95 % or more0 %-31.12.20250.7119ex29331990455-Amino-1-[2,6-dichloro-4-(trifluoromethyl)phenyl]-1H-pyrazole-3-carbonitrile (CAS RN 120068-79-3)0 %-31.12.20260.8046ex29331990481-(3-Iodo-1-isopropyl-1H-pyrazol-4-yl)ethanone (CAS RN 1269440-49-4) with a purity by weight of 98 % or more0 %-31.12.20250.3992ex2933199050Fenpyroximate (ISO) (CAS RN 134098-61-6)0 %-31.12.20240.8240ex29331990533-[2-(Dispiro[2.0.24.13]heptan-7-yl)ethoxy]-1H-pyrazole-4-carboxylic acid (CAS RN 2608048-67-3) with a purity by weight of 98 % or more0 %-31.12.20260.4494ex2933199060Pyraflufen-ethyl (ISO) (CAS RN 129630-19-9)0 %-31.12.20240.7576ex29331990654-Bromo-1-(1-ethoxyethyl)-1H-pyrazole (CAS RN 1024120-52-2)0 %-31.12.20240.4404ex29331990704,5-Diamino-1-(2-hydroxyethyl)-pyrazolsulphate (CAS RN 155601-30-2)0 %-31.12.20240.8312ex2933210045Sodium (5S,8S)-8-methoxy-2,4-dioxo-1,3-diazaspiro[4.5]decan-3-ide (CAS RN 1400584-86-2) with a purity by weight of 90 % or more0 %-31.12.2026

0.4084ex29332100501-Bromo-3-chloro-5,5-dimethylhydantoin (CAS RN 16079-88-2) / (CAS RN 32718-18-6)0 %-31.12.20260.6835ex29332100551-Aminohydantoin hydrochloride (CAS RN 2827-56-7)0 %-31.12.20250.4088ex2933210060DL-p-Hydroxyphenylhydantoin (CAS RN 2420-17-9)0 %-31.12.20260.5115ex29332100805,5-Dimethylhydantoin (CAS RN 77-71-4)0 %-31.12.20250.5972ex2933299015Ethyl 4-(1-hydroxy-1-methylethyl)-2-propylimidazole-5-carboxylate (CAS RN 144689-93-0)0 %-31.12.20240.7527ex29332990182-(2-Chlorophenyl)-1-[2-(2-chlorophenyl)-4,5-diphenyl-2H-imidazol-2-yl]-4,5-diphenyl-1H-imidazole (CAS RN 7189-82-4)0 %-31.12.20240.8150ex2933299020tert-Butyl (2S)-2-(5-bromo-1H-imidazol-2-yl)pyrrolidine-1-carboxylate (CAS RN 1007882-59-8) with a purity by weight of 98 % or more0 %-31.12.20260.7937ex29332990231,1’-Thiocarbonylbis(imidazole) (CAS RN 6160-65-2) with a purity by weight of 95 % or more0 %-31.12.20250.5920ex2933299028Prochloraz (ISO) (CAS RN 67747-09-5) with purity by weight of 97 % or more0 %-31.12.20240.8452ex2933299038Cyazofamid (ISO) (CAS RN 120116-88-3) with a purity by weight of 94 % or more0 %-31.12.20270.5921ex2933299045Prochloraz copper chloride (ISO) (CAS RN 156065-03-1)0 %-31.12.20240.2752ex29332990501,3-Dimethylimidazolidin-2-one (CAS RN 80-73-9)0 %-31.12.20240.6263ex2933299055Fenamidone (ISO) (CAS RN 161326-34-7) with a purity by weight of 97 % or more0 %-31.12.20240.5215ex29332990601-Cyano-2-methyl-1-[2-(5-methylimidazol-4-ylmethylthio)ethyl]isothiourea (CAS RN 52378-40-2)0 %-31.12.20260.7120ex29332990752,2’-Azobis[2-(2-imidazolin-2-yl)propane] dihydrochloride (CAS RN 27776-21-2)0 %-31.12.20260.5821ex2933299080Imazalil (ISO) (CAS RN 35554-44-0)0 %-31.12.2027 0.641529333950Fluroxypyr (ISO) methyl ester (CAS RN 69184-17-4)0 %-31.12.20240.8574ex2933399904Methyl 4-aminopicolinate (CAS RN 71469-93-7) with a purity by weight of 98 % or more0 %-31.12.20280.8524ex29333999052,6-Bis-[1-(2-tert-butylphenylimino)-ethyl]pyridine (CAS RN 204203-17-8) with a purity by weight of 95 % or more0 %-31.12.20280.8576ex2933399906Tert-butyl (3S)-3-hydroxypiperidine-1-carboxylate (CAS RN 143900-44-1) with a purity by weight of 97 % or more0 %-31.12.20280.8535ex29333999075-Bromo-2-methoxypyridine (CAS RN 13472-85-0) with a purity by weight of 99 % or more0 %-31.12.20280.8485ex2933399908Fluazinam (ISO) (CAS RN 79622-59-6) with a purity by weight of 97 % or more0 %-31.12.20270.7186ex29333999102-Aminopyridin-4-ol hydrochloride (CAS RN 1187932-09-7)0 %-31.12.20260.6462ex29333999112-(Chloromethyl)-4-(3-methoxypropoxy)-3-methylpyridine hydrochloride (CAS RN 153259-31-5)0 %-31.12.20240.5608ex29333999122,3-Dichloropyridine (CAS RN 2402-77-9)0 %-31.12.20270.8238ex2933399915(S)-6-Bromo-2-(4-(3-(1,3-dioxoisoindolin-2-yl)propyl)-2,2-dimethylpyrrolidin-1-yl)nicotinamide (CAS RN 2606972-45-4) with a purity by weight of 98 % or more0 %-31.12.20260.8239ex2933399918Perfluorophenyl 6-fluoropyridine-2-sulfonate (CAS RN 2608048-81-1) with a purity by weight of 98 % or more0 %-31.12.20260.6545ex2933399921Boscalid (ISO) (CAS RN 188425-85-6)0 %-31.12.20240.8329ex2933399922N-(5-bromo-3-methylpyridin-2-yl)-N-methylbenzamide (CAS RN 446299-80-5) with a purity by weight of 98 % or more0 %-31.12.20270.4594ex29333999242-Chloromethyl-4-methoxy-3,5-dimethylpyridine hydrochloride (CAS RN 86604-75-3)0 %-31.12.20240.3604ex2933399925Imazethapyr (ISO) (CAS RN 81335-77-5)0 %-31.12.20240.7091ex2933399927Pyridine-2,6-dicarboxylic acid (CAS RN 499-83-2)0 %-31.12.2026

0.6368ex2933399928Ethyl-3-[(3-amino-4-methylamino-benzoyl)-pyridin-2-yl-amino]-propionate (CAS RN 212322-56-0)0 %-31.12.20240.8068ex29333999304-Amino-3-(4-phenoxyphenyl)-1-[(3R)-piperidin-3-yl]-1,3-dihydro-2H-imidazo[4,5-c]pyridin-2-one (CAS RN 1971921-35-3) mono oxalate with a purity by weight of the free base of 70 % or more0 %-31.12.20250.6458ex29333999312-(Chloromethyl)-3-methyl-4-(2,2,2-trifluoroethoxy)pyridine hydrochloride(CAS RN 127337-60-4)0 %-31.12.20240.5241ex29333999322-(Chloromethyl)-3,4-dimethoxypyridine hydrochloride (CAS RN 72830-09-2)0 %-31.12.20260.7181ex29333999335-(3-Chlorophenyl)-3-methoxypyridine-2-carbonitrile (CAS RN 1415226-39-9)0 %-31.12.20260.8420ex2933399934Pyridin-3-ol (CAS RN 109-00-2) with a purity by weight of 98 % or more0 %-31.12.20270.3878ex2933399935Aminopyralid (ISO) (CAS RN 150114-71-9)0 %-31.12.20240.7296ex29333999361-[2-[5-Methyl-3-(trifluoromethyl)-1H-pyrazol-1-yl]acetyl]piperidine-4-carbothioamide (CAS RN 1003319-95-6)0 %-31.12.20270.5230ex2933399937Aqueous solution of pyridine-2-thiol-1-oxide, sodium salt (CAS RN 3811-73-2)0 %-31.12.20260.7348ex2933399938(2-Chloropyridin-3-yl) methanol (CAS RN 42330-59-6)0 %-31.12.20270.8356ex29333999402-Hydroxypyridine-N-oxide (CAS RN 13161-30-3) with a purity by weight of 98 % or more0 %-31.12.20270.8266ex2933399942Glasdegib maleate (INN) (CAS RN 2030410-25-2) with a purity by weight of 98 % or more0 %-31.12.20260.7121ex2933399946Fluopicolide (ISO) (CAS RN 239110-15-7) with a content by weight of 97 % or more0 %-31.12.20260.4706ex2933399947(-)-trans-4-(4’-Fluorophenyl)-3-hydroxymethyl-N-methylpiperidine (CAS RN 105812-81-5)0 %-31.12.20260.4749ex2933399948Flonicamid (ISO) (CAS RN 158062-67-0)0 %-31.12.2024 0.8335ex29333999492-Phenyl-2-(2-pyridyl)acetamide (CAS RN 7251-52-7) with a purity by weight of 98 % or more0 %-31.12.20270.6812ex2933399950N,4-Dimethyl-1-(phenylmethyl)- 3-piperidinamine hydrochloride (1:2) (CAS RN 1228879-37-5) with a purity by weight of 98 % or more0 %-31.12.20240.5610ex29333999526-Chloro-3-nitropyridin-2-ylamine (CAS RN 27048-04-0)0 %-31.12.20240.4646ex2933399955Pyriproxyfen (ISO) (CAS RN 95737-68-1) of a purity by weight of 97 % or more0 %-31.12.20240.5760ex2933399957Tert-butyl 3-(6-amino-3-methylpyridin-2-yl)benzoate (CAS RN 1083057-14-0)0 %-31.12.20270.7598ex2933399959Chlorpyrifos-Methyl (ISO) (CAS RN 5598-13-0)0 %-31.12.20240.2750ex29333999602-Fluoro-6-(trifluoromethyl)pyridine (CAS RN 94239-04-0)0 %-31.12.20240.7584ex29333999616-Bromopyridin-2-amine (CAS RN 19798-81-3)0 %-31.12.20240.7577ex2933399962Ethyl 2,6-Dichloronicotinate (CAS RN 58584-86-4)0 %-31.12.20240.8527ex29333999631-Methyl-4-piperidone (CAS RN 1445-73-4) with a purity by weight of 97 % or more0 %-31.12.20280.7617ex2933399964Methyl 1-(3-chloropyridin-2-yl)-3-hydroxymethyl-1H-pyrazole-5-carboxylate (CAS RN 960316-73-8)0 %-31.12.20240.3602ex2933399965Acetamiprid (ISO) (CAS RN 135410-20-7)0 %-31.12.20240.5946ex2933399967(1R,3S,4S)-tert-Butyl 3-(6-bromo-1H-benzo[d]imidazol-2-yl)-2azabicyclo[2.2.1]heptane-2-carboxylate (CAS RN 1256387-74-2)0 %-31.12.20240.7616ex29333999681-(3-Chloropyridin-2-yl)-3-[[5-(trifluoromethyl)-2H-tetrazol-2-yl]methyl]-1H-pyrazole-5-carboxylic acid (CAS RN 1352319-02-8) with a purity by weight of 85 % or more0 %-31.12.20240.5494ex29333999702,3-Dichloro-5-trifluoromethylpyridine (CAS RN 69045-84-7)0 %-31.12.20260.7704ex2933399971Diflufenican (ISO) (CAS RN 83164-33-4)0 %-31.12.20240.7737ex29333999736-Chloro-4-(4-fluoro-2-methylphenyl)pyridin-3-amine hydrochloride0 %-31.12.20240.7844ex29333999744-Aminopyridine-2-carboxamide (CAS RN 100137-47-1) with a purity by weight of 98 % or more0 %-31.12.2024

0.8072ex2933399975Clodinafop-propargyl (ISO) (CAS RN 105512-06-9) with a purity by weight of 90 % or more0 %-31.12.20250.7813ex2933399976Apalutamide (INN) (CAS RN 956104-40-8)0 %-31.12.20240.5922ex2933399977Imazamox (ISO) (CAS RN 114311-32-9)0 %-31.12.20240.7818ex2933399978Niraparib tosylate monohydrate (INNM) (CAS RN 1613220-15-7)0 %-31.12.20240.7754ex2933399979Avibactam (INN) – sodium (CAS RN 1192491-61-4)0 %-31.12.20240.8074ex2933399980Tert-Butyl (3R)-3-(4-amino-2-oxo-2,3-dihydro-1H-imidazo[4, 5-c]pyridin-1-yl)piperidine-1-carboxylate (CAS RN 1971921-33-1) with a purity by weight of 95 % or more0 %-31.12.20250.7906ex29333999814-Hydroxy-3-pyridinesulphonic acid (CAS RN 51498-37-4) with a purity by weight of 98 % or more0 %-31.12.20240.7866ex2933399982Picloram (ISO) (CAS RN 1918-02-1) containing by weight not more than 15 % of water and with a dry weight purity of 92 % or more0 %-31.12.20240.7976ex29333999832-Hydroxy-4-azoniaspiro[3,5]nonane chloride (CAS RN 15285-58-2) with a purity by weight of 97 % or more0 %-31.12.20250.7925ex2933399984Diethyl(3-pyridyl)borane (CAS RN 89878-14-8) with a purity by weight of 98 % or more0 %-31.12.20250.5129ex29333999852-Chloro-5-chloromethylpyridine (CAS RN 70258-18-3)0 %-31.12.20250.7981ex29333999863-(N-Hydroxycarbamimidoyl)pyridine 1-oxide (CAS RN 92757-16-9) with a purity by weight of 97 % or more0 %-31.12.20250.7939ex29333999876-Chloro-N-(2,2-dimethylpropyl)pyridine-3-carboxamide (CAS RN 585544-20-3) with a purity by weight of 97 % or more0 %-31.12.20250.8096ex29333999891-Benzyl-4-phenylpiperidine-4-carbonitrile monohydrochloride (CAS RN 71258-18-9) with a purity by weight of 98 % or more0 %-31.12.20250.3603ex2933491010Quinmerac (ISO) (CAS RN 90717-03-6)0 %-31.12.20240.4525ex29334910203-Hydroxy-2-methylquinoline-4-carboxylic acid (CAS RN 117-57-7)0 %-31.12.2024 0.6339ex29334910404,7-Dichloroquinoline (CAS RN 86-98-6)0 %-31.12.20240.6773ex29334910501-Cyclopropyl-6,7,8-trifluoro-1,4-dihydro-4-oxo-3-quinolinecarboxylic acid (CAS RN 94695-52-0)0 %-31.12.20250.7098ex2933499025Cloquintocet-mexyl (ISO) (CAS RN 99607-70-2)0 %-31.12.20260.4927ex2933499030Quinoline (CAS RN 91-22-5)0 %-31.12.20250.7524ex29334990456,7-Dimethoxy-3,4- dihydroisoquinoline hydrochloride (CAS RN 20232-39-7)0 %-31.12.20240.8037ex29334990552-(tert-Butoxycarbonyl)-5,7-dichloro-1,2,3,4-tetrahydroisoquinoline-6-carboxylic acid (CAS RN 851784-82-2) with a purity by weight of 98 % or more0 %-31.12.20250.3880ex2933499070Quinolin-8-ol (CAS RN 148-24-3)0 %-31.12.20240.8358ex29334990752-Methyl-4-(1-methyl-1H-1,2,4-triazol-5-yl)quinolin-8-ol (CAS RN 1174132-59-2) with a purity by weight of 98 % or more0 %-31.12.20270.8556ex2933499085(2R,4S)-2-Ethyl-6-(trifluoromethyl)-1,2,3,4-tetrahydroquinolin-4-amine methanesulfonate (CAS RN 952582-02-4) with a purity by weight of 95 % or more0 %-31.12.20280.4043ex2933520010Malonylurea (barbituric acid) (CAS RN 67-52-7)0 %-31.12.20260.7631ex29335400105,5’-(1,2-Diazenediyl)bis [2,4,6 (1H, 3H, 5H)-pyrimidinetrione] (CAS RN 25157-64-6)0 %-31.12.20240.6468ex29335995106-Amino-1,3-dimethyluracil (CAS RN 6642-31-5)0 %-31.12.20240.6151ex29335995132-Diethylamino-6-hydroxy-4-methylpyrimidine (CAS RN 42487-72-9)0 %-31.12.20240.8597ex29335995142-Chloro-7-cyclopentyl-N,N-dimethyl-7H-pyrrolo[2,3-d]pyrimidine-6-carboxamide (CAS RN 1211443-61-6) with a purity by weight of 97 % or more0 %-31.12.20280.2578ex2933599515Sitagliptin phosphate monohydrate (CAS RN 654671-77-9)0 %-31.12.20240.8580ex2933599516Tert-butyl 4-(6-aminopyridin-3-yl)piperazine-1-carboxylate (CAS RN 571188-59-5) with a purity by weight of 98 % or more0 %-31.12.2028

0.8555ex2933599519Tert-butyl 4-[(2-chloropyrimidin-5-yl)oxy]butanoate (CAS RN 945771-55-1) with a purity by weight of 95 % or more0 %-31.12.20280.2745ex29335995202,4-Diamino-6-chloropyrimidine (CAS RN 156-83-2)0 %-31.12.20240.6763ex2933599521N-(2-Oxo-1,2-dihydropyrimidin-4-yl)benzamide (CAS RN 26661-13-2)0 %-31.12.20250.5912ex29335995272-[(2-Amino-6-oxo-1,6-dihydro-9H-purin-9-yl)methoxy]-3-hydroxypropylacetate (CAS RN 88110-89-8)0 %-31.12.20240.7810ex29335995286,8-Difluoro-1-(methylamino)-7-(4-methylpiperazin-1-yl)-4-oxo-1,4-dihydroquinoline-3-carboxylic acid (CAS RN 100276-37-7)0 %-31.12.20240.8157ex29335995292-Amino-4-(4-methylpiperazin-1-yl) benzoic acid tert-butyl ester (CAS RN 1034975-35-3) with a purity by weight of 95 % or more0 %-31.12.20260.3600ex2933599530Mepanipyrim (ISO) (CAS RN 110235-47-7)0 %-31.12.20240.8376ex2933599531Sotorasib (INN) (CAS RN 2296729-00-3) with a purity by weight of 99 % or more0 %-31.12.20270.8456ex29335995325-Chloro-3-nitropyrazolo[1,5-a]pyrimidine (CAS RN 1363380-51-1) with a purity by weight of 98 % or more0 %-31.12.20270.6240ex29335995334,6-Dichloro-5-fluoropyrimidine (CAS RN 213265-83-9)0 %-31.12.20240.7370ex29335995346-chloro-1,3-dimethyluracil (CAS RN 6972-27-6) with a purity by weight of 97 % or more0 %-31.12.20240.7345ex29335995361-(Cyclopropylcarbonyl)piperazine hydrochloride (CAS RN 1021298-67-8) with a purity by weight of 98 % or more0 %-31.12.20240.6419ex29335995376-Iodo-3-propyl-2-thioxo-2,3-dihydroquinazolin-4(1H)-one (CAS RN 200938-58-5)0 %-31.12.20240.8248ex29335995385-(5-Chlorosulfonyl-2-ethoxyphenyl)-1-methyl-3-propyl-1,6-dihydro-7H-pyrazolo[4,3-d]pyrimidin-7-one (CAS RN 139756-22-2) with a purity by weight of 98 % or more0 %-31.12.20260.8243ex29335995412-(4-Phenoxyphenyl)-7-(piperidin-4-yl)-4,5,6,7-tetrahydropyrazolo[1,5-a]pyrimidine-3-carbonitrile (CAS RN 2190506-57-9) with a purity by weight of 98 % or more0 %-31.12.2026 0.8056ex29335995422-Chloropyrimidine (CAS RN 1722-12-9) with a purity by weight of 98 % or more0 %-31.12.20250.8484ex29335995441,4,5,6-Tetrahydro-1,2-dimethylpyrimidine (CAS RN 4271-96-9) with a purity by weight of 98 % or more0 %-31.12.20270.4704ex29335995451-[3-(Hydroxymethyl)pyridin-2-yl]-4-methyl-2-phenylpiperazine (CAS RN 61337-89-1)0 %-31.12.20240.8488ex2933599546Trilaciclib (CAS RN 1374743-00-6) with a purity by weight of 99 % or more0 %-31.12.20270.6677ex29335995476-Methyl-2-oxoperhydropyrimidin-4-ylurea (CAS RN 1129-42-6) with a purity of 94 % or more0 %-31.12.20250.4699ex29335995502-(2-Piperazin-1-ylethoxy)ethanol (CAS RN 13349-82-1)0 %-31.12.20240.6987ex29335995526-Benzyladenine (CAS RN 1214-39-7) with a purity by weight of 97 % or more0 %-31.12.20260.2744ex29335995602,6-Dichloro-4,8-dipiperidinopyrimido[5,4-d]pyrimidine (CAS RN 7139-02-8)0 %-31.12.20240.7578ex29335995631-(3-Chlorophenyl) piperazine (CAS RN 6640-24-0)0 %-31.12.20240.4772ex29335995651-Chloromethyl-4-fluoro-1,4-diazoniabicyclo[2.2.2]octane bis(tetrafluoroborate) (CAS RN 140681-55-6)0 %-31.12.20240.7825ex2933599568Guanine (CAS RN 73-40-5) with a purity by weight of 99 % or more0 %-31.12.20240.2735ex2933599570N-(4-Ethyl-2,3-dioxopiperazin-1-ylcarbonyl)-D-2-phenylglycine (CAS RN 63422-71-9)0 %-31.12.20240.5542ex29335995773-(Trifluoromethyl)-5,6,7,8-tetrahydro[1,2,4]triazolo[4,3-a]pyrazine hydrochloride (1:1) (CAS RN 762240-92-6)0 %-31.12.20270.7071ex29335995875-Bromo-2,4-dichloropyrimidine (CAS RN 36082-50-5)0 %-31.12.20260.6774ex2933698013Metribuzin (ISO) (CAS RN 21087-64-9) with a purity by weight of 93 % or more0 %-31.12.20250.6621ex29336980152-Chloro-4,6-dimethoxy-1,3,5-triazine (CAS RN 3140-73-6)0 %-31.12.20250.6951ex2933698017Benzoguanamine (CAS RN 91-76-9)0 %-31.12.2026

0.7721ex29336980231,3,5-Tris(2,3-dibromopropyl)-1,3,5-triazinane-2,4,6-trione (CAS RN 52434-90-9)0 %-31.12.20240.7600ex2933698027Troclosene sodium dihydrate (INNM) (CAS RN 51580-86-0)0 %-31.12.20240.7952ex29336980332,4,6-Trichloro-1,3,5-triazine (CAS RN 108-77-0) with a purity by weight of 99 % or more0 %-31.12.20250.5272ex2933698040Troclosene sodium (INNM) (CAS RN 2893-78-9)0 %-31.12.20260.7464ex29336980452-(4,6-Bis-(2,4-dimethylphenyl)-1,3,5-triazin-2-yl)-5-(octyloxy)-phenol (CAS RN 2725-22-6)0 %-31.12.20240.5131ex2933698055Terbutryn (ISO) (CAS RN 886-50-0)0 %-31.12.20250.4957ex2933698060Cyanuric acid (CAS RN 108-80-5)0 %-31.12.20250.6127ex29336980651,3,5-Triazine-2,4,6(1H,3H,5H)-trithione, trisodium salt (CAS RN 17766-26-6)0 %-31.12.20240.6477ex2933698075Metamitron (ISO) (CAS RN 41394-05-2)0 %-31.12.20240.3882ex2933698080Tris(2-hydroxyethyl)-1,3,5-triazinetrione (CAS RN 839-90-7)0 %-31.12.20240.6960ex2933790015Ethyl N-(tert-Butoxycarbonyl)-L-pyroglutamate (CAS RN 144978-12-1)0 %-31.12.20260.7346ex2933790025Methyl 2-oxo-2,3-dihydro-1H-indole-6-carboxylate (CAS RN 14192-26-8)0 %-31.12.20240.4294ex29337900305-Vinyl-2-pyrrolidone (CAS RN 7529-16-0)0 %-31.12.20270.7453ex29337900351-tert-Butyl 2-methyl(2S)-5-oxopyrrolidine-1,2-dicarboxylate (CAS RN 108963-96-8)0 %-31.12.20240.8038ex29337900451-Phenyl-3H-indol-2-one (CAS RN 3335-98-6) with a purity by weight of 99 % or more0 %-31.12.20250.4524ex29337900506-Bromo-3-methyl-3H-dibenz(f,ij)isoquinoline-2,7-dione (CAS RN 81-85-6)0 %-31.12.20240.8203ex2933790055(3S,4R)-3-Amino-4-hydroxypyrrolidin-2-one hydrochloride (CAS RN 2446872-13-3) with a purity by weight of 98 % or more0 %-31.12.2026 0.8212ex29337900651-Dodecyl-2-pyrrolidone (CAS RN 2687-96-9) with a purity by weight of 98 % or more0 %-31.12.20260.4985ex2933790070(S)-N-[(Diethylamino)methyl]-alpha-ethyl-2-oxo-1-pyrrolidineacetamide L-(+)-tartrate, (CAS RN 754186-36-2)0 %-31.12.20250.8351ex2933790075N-(n-octyl)-2-pyrrolidone (CAS RN 2687-94-7) with a purity by weight of 99 % or more0 %-31.12.20270.8354ex2933790080(S)-2-Amino-3-[(S)-2-oxopyrrolidin-3-yl]propanamide hydrochloride (CAS RN 2628280-48-6) with a purity by weight of 98 % or more0 %-31.12.20270.8545ex29337900853,5-Dibromo-1-methyl-2(1H)-pyridinone (CAS RN 14529-54-5) with a purity by weight of 97 % or more0 %-31.12.20280.8547ex29339980013-Cyanoindole (CAS RN 5457-28-3) with a purity by weight of 98 % or more0 %-31.12.20280.8548ex2933998002(S)-1-Benzyl-3-pyrrolidinol (CAS RN 101385-90-4) with a purity by weight of 98 % or more0 %-31.12.20280.8581ex2933998003Tert-butyl 4-formyl-5-methoxy-7-methyl-1H-indole-1-carboxylate (CAS RN 1481631-51-9) with a purity by weight of 97 % or more0 %-31.12.20280.8523ex2933998004(S)-2,5-Dihydro-pyrrole-1,2-dicarboxylic acid 1-tert-butyl ester 2-methyl ester (CAS RN 74844-93-2) with a purity by weight of 97 % or more0 %-31.12.20280.3580ex2933998006Metconazole (ISO) (CAS RN 125116-23-6) with a purity by weight of 98 % or more0 %-31.12.20240.8156ex29339980074-(2-Oxo-2,3-dihydro-1H-benzimidazol-1-yl)butanoic acid (CAS RN 3273-68-5) with a purity by weight of 98 % or more0 %-31.12.20260.8180ex2933998008Prothioconazole (ISO) (CAS RN 178928-70-6) with a purity by weight of 98 % or more0 %-31.12.20260.8202ex29339980095,7-Difluoro-2-(4-fluorophenyl)-1H-indole (CAS RN 901188-04-3) with a purity by weight of 98 % or more0 %-31.12.20260.8324ex2933998010(R)-2-(2,5-difluorophenyl)pyrrolidine hydrochloride (CAS RN 1218935-60-4) with a purity by weight of 98 % or more0 %-31.12.2027

0.6563ex2933998011Fenbuconazole (ISO) (CAS RN 114369-43-6)0 %-31.12.20240.6564ex2933998012Myclobutanil (ISO) (CAS RN 88671-89-0)0 %-31.12.20240.5243ex29339980135-Difluoromethoxy-2-mercapto-1-H-benzimidazole (CAS RN 97963-62-7)0 %-31.12.20260.6146ex29339980142-(2H-benzotriazol-2-yl)-4-methyl-6-(2-methylprop-2-en-1-yl)phenol (CAS RN 98809-58-6)0 %-31.12.20240.6872ex2933998016Pyridate (ISO) (CAS RN 55512-33-9) with a purity by weight of 90 % or more0 %-31.12.20250.8359ex2933998017(1R,2S,5S)-3-[(S)-3,3-dimethyl-2-(2,2,2-trifluoroacetamido)butanoyl]-6,6-dimethyl-3-azabicyclo[3.1.0]hexane-2-carboxylic acid (CAS RN 2755812-45-2) with a purity by weight of 98 % or more0 %-31.12.20270.8290ex29339980182-(2-Ethoxyphenyl)-5-methyl-7-propylimidazolo[5,1-f][1,2,4]-triazin-4(3H)-one (CAS RN 224789-21-3) with a purity by weight of 95 % or more0 %-31.12.20260.6567ex29339980192-(2,4-Dichlorophenyl)-3-(1H-1,2,4-triazol-1-yl)propan-1-ol (CAS RN 112281-82-0)0 %-31.12.20240.2732ex29339980202-(2H-Benzotriazol-2-yl)-4,6-bis(1-methyl-1-phenylethyl)phenol (CAS RN 70321-86-7)0 %-31.12.20240.6829ex29339980211-(Bis(dimethylamino)methylene)-1H-[1,2,3]triazolo[4,5-b]pyridinium 3-oxide hexafluorophosphate(V) (CAS RN 148893-10-1)0 %-31.12.20250.8249ex2933998022Dibenz[b,f]azepine-5-carbonyl chloride (CAS RN 33948-22-0) with a purity by weight of 98 % or more0 %-31.12.20260.6244ex2933998023Tebuconazole (ISO) (CAS RN 107534-96-3) with a purity by weight of 95 % or more0 %-31.12.20240.5625ex29339980241,3-Dihydro-5,6-diamino-2H-benzimidazol-2-one (CAS RN 55621-49-3)0 %-31.12.20270.8089ex29339980256-(4-Benzylamino-3-nitrophenyl)-5-methyl-4,5-dihydro-2H-pyridazin-3-one (CAS RN 77469-62-6) with a purity by weight of 95 % or more0 %-31.12.2025 0.8418ex2933998026Benzotriazole-1-yl-oxy-tris-pyrrolidino-phosphonium hexafluorophosphate (CAS RN 128625-52-5) with a purity by weight of 97 % or more0 %-31.12.20270.6409ex29339980275,6-Dimethylbenzimidazole (CAS RN 582-60-5)0 %-31.12.20240.8357ex29339980287-(2-Methyl-4-nitrophenoxy)-[1,2,4]triazolo[1,5-a]pyridine (CAS RN 937263-44-0) with a purity by weight of 98 % or more0 %-31.12.20270.3593ex2933998030Quizalofop-P-ethyl (ISO) (CAS RN 100646-51-3)0 %-31.12.20240.8284ex29339980321H-1,2,3-Triazole (CAS RN 288-36-8) or 2H-1,2,3-triazole (CAS RN 288-35-7) with a purity by weight of 99 % or more0 %-31.12.20260.6249ex2933998033Penconazole (ISO) (CAS RN 66246-88-6)0 %-31.12.20240.7043ex29339980342,4-Dihydro-5-methoxy-4-methyl-3H-1,2,4-triazol-3-on (CAS RN 135302-13-5)0 %-31.12.20260.6958ex29339980363-Chloro-2-(1,1-difluoro-3-buten-1-yl)-6-methoxyquinoxaline (CAS RN 1799733-46-2)0 %-31.12.20240.4695ex29339980378-Chloro-5,10-dihydro-11H-dibenzo [b,e] [1,4]diazepin-11-one (CAS RN 50892-62-1)0 %-31.12.20240.7045ex2933998038(4aS,7aS)-Octahydro-1H-pyrrolo[3,4-b]pyridine (CAS RN 151213-40-0)0 %-31.12.20260.3591ex2933998040trans-4-Hydroxy-L-proline (CAS RN 51-35-4)0 %-31.12.20240.7273ex29339980415-[4’-(Bromomethyl)biphenyl-2-yl]-1-trityl-1H-tetrazole (CAS RN 124750-51-2)0 %-31.12.20270.7185ex2933998042(S)-2,2,4-Trimethylpyrrolidine hydrochloride (CAS RN 1897428-40-8)0 %-31.12.20260.8455ex29339980434-([1,2,4]Triazolo[1,5-a]pyridin-7-yloxy)-3-methylaniline (CAS RN 937263-71-3) with a purity by weight of 98 % or more0 %-31.12.20270.3582ex2933998045Maleic hydrazide (ISO) (CAS RN 123-33-1)0 %-31.12.20240.7269ex2933998046(S)-Indoline-2-carboxylic acid (CAS RN 79815-20-6)0 %-31.12.20270.5818ex2933998047Paclobutrazol (ISO) (CAS RN 76738-62-0)0 %-31.12.2027

0.7410ex29339980485-Amino-6-methyl-2-benzimidazolone (CAS RN 67014-36-2)0 %-31.12.20270.5945ex2933998053Potassium (S)-5-(tert-butoxycarbonyl)-5-azaspiro[2.4]heptane-6-carboxylate (CAS RN 1441673-92-2)0 %-31.12.20240.6599ex29339980543-(Salicyloylamino)-1,2,4-triazole (CAS RN 36411-52-6)0 %-31.12.20250.4585ex2933998055Pyridaben (ISO) (CAS RN 96489-71-3)0 %-31.12.20240.7457ex2933998056Methyl 3,5-diamino-6-chloropyrazine-2-carboxylate (CAS RN 1458-01-1)0 %-31.12.20240.5901ex29339980572-(5-Methoxyindol-3-yl)ethylamine (CAS RN 608-07-1)0 %-31.12.20240.7649ex2933998058Ipconazole (ISO) (CAS RN 125225-28-7) with a purity by weight of 90 % or more0 %-31.12.20240.7673ex2933998059Hydrates of Hydroxybenzotriazole (CAS RN 80029-43-2 and CAS RN 123333-53-9)0 %-31.12.20240.7927ex29339980602-[(6,11-Dihydro-5H-dibenz[b,e]azepin-6-yl)-methyl]-1H-isoindole-1,3(2H)-dione (CAS RN 143878-20-0) with a purity by weight of 99 % or more0 %-31.12.20250.7624ex2933998061(1R,5S)-8-Benzyl-8-azabicyclo(3.2.1)octan-3-one hydrochloride (CAS RN 83393-23-1)0 %-31.12.20240.7680ex2933998063L-Prolinamide (CAS RN 7531-52-4)0 %-31.12.20240.7839ex2933998066(6-(4-Fluorobenzyl)-3,3-dimethyl-2,3-dihydro-1H-pyrrolo[3,2-b]pyrid-5-yl)methanol (CAS RN 1799327-42-6) with a purity by weight of 98 % or more0 %-31.12.20240.5468ex2933998067Candesartan ethyl ester (INNM) (CAS RN 139481-58-6)0 %-31.12.20260.7679ex29339980685-((1S,2S)-2-((2R,6S,9S,11R,12R,14aS,15S,16S,20R,23S,25aR)-9-Amino-20-((R)-3-amino-1-hydroxy-3-oxopropyl)-2,11,12,15-tetrahydroxy-6-((R)-1-hydroxyethyl)-16-methyl-5,8,14,19,22,25-hexaoxotetracosahydro-1H-dipyrrolo[2,1-c:2’,1’-l][1,4,7,10,13,16]hexaazacyclohenicosin-23-yl)–1,2-dihydroxyethyl)-2-hydroxyphenyl hydrogen sulphate (CAS RN 168110-44-9)0 %-31.12.20240.8053ex29339980695-Formyl-2,4-dimethyl-1H-pyrrole-3-carboxylic acid (CAS RN 253870-02-9) with a purity by weight of 96 % or more0 %-31.12.2025 0.7971ex29339980705-(Bis-(2-hydroxyethyl)-amino)-1-methyl-1H-benzimidazole-2-butanoic acid ethyl ester (CAS RN 3543-74-6) with a purity by weight of 98 % or more0 %-31.12.20250.4384ex293399807110-Methoxyiminostilbene (CAS RN 4698-11-7)0 %-31.12.20240.4503ex29339980721,4,7-Trimethyl-1,4,7-triazacyclononane (CAS RN 96556-05-7)0 %-31.12.20240.7759ex29339980751-[Bis(dimethylamino)methylene]-1H-benzotriazolium hexafluorophosphate(1-) 3-oxide (CAS RN 94790-37-1)0 %-31.12.20240.8054ex29339980762-Methylindoline (CAS RN 6872-06-6) with a purity by weight of 98 % or more0 %-31.12.20250.8064ex29339980779-[1,1'-Biphenyl]-3-yl-9'-[1,1'-biphenyl]-4-yl-3,3'-bi-9H-carbazole (CAS RN 1643479-47-3) with a purity by weight of 95 % or more0 %-31.12.20250.4382ex29339980783-Amino-3-azabicyclo (3.3.0) octane hydrochloride (CAS RN 58108-05-7)0 %-31.12.20240.8014ex2933998080Pyrrole-2-carboxaldehyde (CAS RN 1003-29-8) with a purity by weight of 97 % or more0 %-31.12.20250.4164ex29339980811,2,3-Benzotriazole (CAS RN 95-14-7)0 %-31.12.20260.4165ex2933998082Tolytriazole (CAS RN 29385-43-1)0 %-31.12.20240.6933ex2933998087Carfentrazone-ethyl (ISOM) (CAS RN 128639-02-1) with a purity by weight of 90 % or more0 %-31.12.20250.3579ex2934100010Hexythiazox (ISO) (CAS RN 78587-05-0)0 %-31.12.20240.2725ex29341000202-(4-Methylthiazol-5-yl)ethanol (CAS RN 137-00-8)0 %-31.12.20240.5538ex2934100035(2-Isopropylthiazol-4-yl)-N-methylmethanamine dihydrochloride (CAS RN 1185167-55-8)0 %-31.12.20270.6264ex29341000452-Cyanimino-1,3-thiazolidine (CAS RN 26364-65-8)0 %-31.12.20240.4750ex2934100060Fosthiazate (ISO) (CAS RN 98886-44-3)0 %-31.12.20240.7312ex2934208015Benthiavalicarb-isopropyl (ISO) (CAS RN 177406-68-7)0 %-31.12.2027

0.4346ex29342080251,2-Benzisothiazol-3(2H)-one (CAS RN 2634-33-5) in the form of a powder with a purity by weight of 95 % or more, or in an aqueous mixture containing by weight 20 % or more of 1,2-benzisothiazol-3(2H)-one0 %-31.12.20270.4910ex2934208070N,N-Bis(1,3-benzothiazol-2-ylsulphanyl)-2-methylpropan-2-amine (CAS RN 3741-80-8)0 %-31.12.20250.5537ex29343090102-Methylthiophenothiazine (CAS RN 7643-08-5)0 %-31.12.20270.8571ex2934999004Silthiofam (ISO) (CAS RN 175217-20-6) with a purity by weight of 98 % or more0 %-31.12.20280.8551ex2934999005(S)-2-Methyl-1-(6-nitropyridin-3-yl)-4-(oxetan-3-yl)piperazine (CAS RN 1895867-67-0) with a purity by weight of 97 % or more0 %-31.12.20280.8560ex2934999006Cis-[2-(2,4-Dichlorodiphenyl)-2-(1H-imidazol-1-ylmethyl)-1,3-dioxolan-4yl]methyl-4-methylbenzenesulfonate (CAS RN 134071-44-6) with a purity by weight of 99 % or more0 %-31.12.20280.8487ex2934999007Cedazuridine (INN) (CAS RN 1141397-80-9) with a purity by weight of 99 % or more0 %-31.12.20270.8472ex2934999008(R)-tert-butyl 2-(6-(5-chloro-2-((tetrahydro-2H-pyran-4-yl)amino)pyrimidin-4-yl)-1-oxoisoindolin-2-yl)propanoate (CAS RN 2095665-45-3) with a purity by weight of 98 % or more0 %-31.12.20270.8449ex29349990093-[2-{(2R,3S)-3-[(1R)-1-{[tert-butyl(dimethyl)silyl]oxy}ethyl]-4-oxoazetidin-2-yl}propanoyl]-4,4-dimethyl-1,3-oxazolidin-2-one (isomeric mixture of CAS RNs 114341-89-8 and 114418-63-2) with a purity by weight of 99 % or more0 %-31.12.20270.6492ex2934999010Fluralaner (INN) (CAS RN 864731-61-3)0 %-31.12.20240.8388ex2934999011Aqueous solution of d(P-thio)(T-G-A-C-T-G-T-G-A-A-C-G-T-T-C-G-A-G-A-T-G-A) deoxyribonucleic acid (CAS RN 937402-51-2), containing by weight 15 % or more, but not more than 25 % of oligodeoxynucleotide0 %-31.12.20270.5924ex2934999012Dimethomorph (ISO) (CAS RN 110488-70-5)0 %-31.12.20240.8348ex2934999013(6S)-6-methyl-5,6-Dihydro-4H-thieno[2,3-b]thiopyran4-one-7,7-dioxide (CAS RN 148719-91-9) with a purity by weight of 98 % or more0 %-31.12.2027 0.8326ex29349990142-Mercaptoadenosine (CAS RN 43157-50-2) with a purity by weight of 98 % or more0 %-31.12.20270.3577ex2934999015Carboxin (ISO) (CAS RN 5234-68-4)0 %-31.12.20240.6476ex2934999016Difenoconazole (ISO) (CAS RN 119446-68-3)0 %-31.12.20240.7843ex2934999017(S)-4-(Tert-butoxycarbonyl)-1,4-oxazepane-2-carboxylic acid (CAS RN 1273567-44-4) with a purity by weight of 95 % or more0 %-31.12.20240.8250ex2934999018Methyl (1R,3R)-1-(1,3-benzodioxol-5-yl)-2-(2-chloroacetyl)-1,3,4,9-tetrahydropyrido[5,4-b]indole-3-carboxylate (CAS RN 171489-59-1) with a purity by weight of 99 % or more0 %-31.12.20260.4715ex2934999020Thiophene (CAS RN 110-02-1)0 %-31.12.20240.8253ex29349990224-(Oxiran-2-ylmethoxy)-9H-carbazole (CAS RN 51997-51-4) with a purity by weight of 97 % or more0 %-31.12.20260.5263ex2934999023Bromuconazole (ISO) with a purity by weight of 96 % or more (CAS RN 116255-48-2)0 %-31.12.20260.6241ex2934999024Flufenacet (ISO) (CAS RN 142459-58-3) with a purity by weight of 95 % or more0 %-31.12.20240.4942ex29349990252,4-Diethyl-9H-thioxanthen-9-one (CAS RN 82799-44-8)0 %-31.12.20250.6252ex29349990264-Methylmorpholine 4-oxide in an aqueous solution (CAS RN 7529-22-8)0 %-31.12.20240.6362ex29349990272-(4-Hydroxyphenyl)-1-benzothiophene-6-ol (CAS RN 63676-22-2)0 %-31.12.20240.5242ex293499902811-(Piperazin-1-yl)dibenzo[b,f][1,4]thiazepine dihydrochloride (CAS RN 111974-74-4)0 %-31.12.20260.7837ex2934999029(2R,5S)-tert-Butyl 4-benzyl-2-methyl-5-(((R)-3-methylmorpholino)methyl)piperazine-1-carboxylate (CAS RN 1403902-77-1) with a purity by weight of 98 % or more0 %-31.12.20240.4700ex2934999030Dibenzo[b,f][1,4]thiazepin-11(10H)-one (CAS RN 3159-07-7)0 %-31.12.2024

0.7840ex2934999033(2R,3R,5R)-5-(4-Amino-2-oxopyrimidin-1(2H)-yl)-2-((benzoyloxy)methyl)-4,4-difluorotetrahydrofuran-3-yl benzoate (CAS RN 134790-39-9) with a purity by weight of 98 % or more0 %-31.12.20240.8267ex2934999035Nusinersen sodium (INNM) (CAS RN 1258984-36-9) with a purity by weight of 95 % or more0 %-31.12.20260.5813ex29349990374-Propan-2-ylmorpholine (CAS RN 1004-14-4)0 %-31.12.20270.6824ex29349990394-(Oxiran-2-ylmethoxy)-9H-carbazole (CAS RN 51997-51-4)0 %-31.12.20250.8094ex29349990402,3-Pyrazinedicarboxylic anhydride (CAS RN 4744-50-7) with a purity by weight of 95 % or more0 %-31.12.20250.6823ex293499904111-[4-(2-Chloro-ethyl)-1-piperazinyl]dibenzo(b,f)(1,4)thiazepine (CAS RN 352232-17-8)0 %-31.12.20250.6922ex29349990421-(Morpholin-4-yl)prop-2-en-1-one (CAS RN 5117-12-4)0 %-31.12.20240.8176ex2934999043Fludioxonil (ISO) (CAS RN 131341-86-1) with a purity by weight of 99 % or more0 %-31.12.20260.6893ex2934999044Propiconazole (ISO) (CAS RN 60207-90-1) with a purity by weight of 92 % or more0 %-31.12.20250.8380ex29349990454-[4-[(5s)-5-(Aminomethyl)-2-oxo-3-oxazolidinyl] phenyl]-3-morpholinone, hydrochloride (CAS RN 898543-06-1) with a purity by weight of 98 % or more0 %-31.12.20270.5453ex2934999048Propan-2-ol -- 2-methyl-4-(4-methylpiperazin-1-yl)-10H-thieno[2,3-b][1,5]benzodiazepine (1:2) dihydrate (CAS RN 864743-41-9)0 %-31.12.20260.7188ex2934999049Cytidine 5’-(disodium phosphate) (CAS RN 6757-06-8)0 %-31.12.20260.8330ex2934999051Uridine 5’-triphosphate trisodium salt (CAS RN 19817-92-6) with a dry weight purity of 90 % or more0 %-31.12.20270.7259ex2934999052Epoxiconazole (ISO) (CAS RN 133855-98-8)0 %-31.12.20270.8031ex2934999055Uridine (CAS RN 58-96-8) with a purity by weight of 98 % or more0 %-31.12.20250.7297ex29349990561-[5-(2,6-Difluorophenyl)-4,5-dihydro-1,2-oxazol-3-yl]ethanone (CAS RN 1173693-36-1)0 %-31.12.2027 0.3575ex2934999058Dimethenamide-P (ISO) (CAS RN 163515-14-8)0 %-31.12.20240.7387ex2934999059Dolutegravir (INN) (CAS RN 1051375-16-6) or dolutegravir sodium (CAS RN 1051375-19-9)0 %-31.12.20270.2718ex2934999060DL-Homocysteine thiolactone hydrochloride (CAS RN 6038-19-3)0 %-31.12.20240.7459ex29349990615-(1,2-Dithiolan-3-yl)valeric acid (CAS RN 1077-28-7)0 %-31.12.20240.7536ex2934999062(2b,3a,5a,16b,17b)-2-(Morpholin-4-yl)-16-(pyrrolidin-1-yl)androstane-3,17-diol 17-acetate (CAS RN 119302-24-8)0 %-31.12.20240.7537ex2934999063(2b,3a,5a,16b,17b)-2-(Morpholin-4-yl)-16-(pyrrolidin-1-yl)androstane-3,17-diol (CAS RN 119302-20-4)0 %-31.12.20240.7449ex29349990642-Bromo-5-benzoylthiophene (CAS RN 31161-46-3)0 %-31.12.20240.7926ex2934999065Benzo[b]thiophen-10-methoxycycloheptanone (CAS RN 59743-84-9) with a purity by weight of 98 % or more0 %-31.12.20250.4512ex2934999066Tetrahydrothiophene-1,1-dioxide (CAS RN 126-33-0)0 %-31.12.20240.7809ex2934999068Afatinib dimaleate (INNM) (CAS RN 850140-73-7)0 %-31.12.20240.7842ex29349990693-Methyl-5-(4,4,5,5-tetramethyl-1,3,2-dioxaborolan-2-yl)benzo[d]oxazol-2(3H)-one (CAS RN 1220696-32-1) with a purity by weight of 95 % or more0 %-31.12.20240.7944ex29349990701,3,4-Thiadiazolidine-2,5-dithione (CAS RN 1072-71-5) with a purity by weight of 95 % or more0 %-31.12.20250.8289ex29349990713,4-Dichloro-1,2,5-thiadiazole (CAS RN 5728-20-1) with a purity by weight of 99 % or more0 %-31.12.20260.8317ex29349990722-Trifluoromethyl-9-allyl-9-thioxanthen-ol (CAS RN 850808-70-7) with a purity by weight of 98 % or more0 %-31.12.20270.7731ex2934999073Tetrahydrouridine (CAS RN 18771-50-1)0 %-31.12.20240.4249ex29349990742-Isopropylthioxanthone (CAS RN 5495-84-1)0 %-31.12.20270.4052ex2934999075(4R-cis)-1,1-Dimethylethyl-6-[2[2-(4-fluorophenyl)-5-(1-isopropyl)-3-phenyl-4-[(phenylamino)carbonyl]-1H-pyrrol-1-yl]ethyl]-2,2-dimethyl-1,3-dioxane-4-acetate (CAS RN 125971-95-1)0 %-31.12.2026

0.8221ex2934999077Tazemetostat (INN) (CAS 1403254-99-8) with a purity by weight of 99 % or more and its salts0 %-31.12.20260.4388ex2934999079Thiophen-2-ethanol (CAS RN 5402-55-1)0 %-31.12.20240.7657ex29349990802-(Dimethylamino)-2-[(4-methylphenyl)methyl]-1-[4-(morpholin-4-yl)phenyl]butan-1-one (CAS RN 119344-86-4)0 %-31.12.20240.8048ex29349990811-(4-Aminophenyl)-5-(morpholin-4-yl)-2,3-dihydropyridin-6-one (CAS RN 1267610-26-3) with a purity by weight of 98 % or more0 %-31.12.20250.7815ex2934999082Rel-(3aR,12bR)-11-Chloro-2,3,3a,12b-tetrahydro-2-methyl-1H-dibenz[2,3:6,7]oxepino[4,5-c]pyrrol-1-one (CAS RN 129385-59-7) with a purity by weight of 97 % or more0 %-31.12.20240.4643ex2934999083Flumioxazin (ISO) (CAS RN 103361-09-7) of a purity by weight of 96 % or more0 %-31.12.20240.4645ex2934999084Etoxazole (ISO) (CAS RN 153233-91-1) of a purity by weight of 94,8 % or more0 %-31.12.20240.8222ex2934999085Gilteritinib (INN) (CAS 1254053-43-4) with a purity by weight of 98 % or more and its salts0 %-31.12.20260.5133ex2934999086Dithianon (ISO) (CAS RN 3347-22-6)0 %-31.12.20250.5136ex29349990872,2’-(1,4-Phenylene)bis(4H-3,1-benzoxazin-4-one) (CAS RN 18600-59-4)0 %-31.12.20250.7738ex2934999088(7S,9aS)-7-((Benzyloxy)methyl)octahydropyrazino[2,1-c][1,4]oxazine dioxalate (CAS RN 1268364-46-0)0 %-31.12.20240.6486ex2935909010Florasulam (ISO) (CAS RN 145701-23-1)0 %-31.12.20240.3566ex2935909015Flupyrsulfuron-methyl-sodium (ISO) (CAS RN 144740-54-5)0 %-31.12.20240.8479ex29359090162-Bromo-N-(4,5-dimethyl-1,2-oxazol-3-yl)-N-(methoxymethyl) benzene-1-sulfonamide (CAS RN 415697-57-3) with a purity by weight of 97 % or more0 %-31.12.20270.8173ex29359090184-Amino-2,5-dimethoxy-N-methylbenzenesulfonamide (CAS RN 49701-24-8) with a purity by weight of 98 % or more0 %-31.12.2026 0.8174ex29359090194-Amino-2,5-dimethoxy-N-phenylbenzenesulphonamide (CAS RN 52298-44-9) with a purity by weight of 98 % or more0 %-31.12.20260.3565ex2935909020Toluenesulphonamides0 %-31.12.20240.8224ex2935909021Encorafenib (INN) (CAS 1269440-17-6) with a purity by weight of 99 % or more0 %-31.12.20260.8276ex2935909022Methyl 2-(chlorosulfonyl)-4-(methylsulfonamidomethyl)benzoate (CAS RN 393509-79-0) with a purity by weight of 90 % or more0 %-31.12.20260.5239ex2935909023N-[4-(2-Chloroacetyl)phenyl]methanesulphonamide (CAS RN 64488-52-4)0 %-31.12.20260.8277ex29359090243-({[(4-methylphenyl)sulfonyl]carbamoyl}amino)phenyl 4-methylbenzenesulfonate (CAS RN 232938-43-1) with a purity by weight of 99 % or more0 %-31.12.20260.3563ex2935909025Triflusulfuron-methyl (ISO) (CAS RN 126535-15-7)0 %-31.12.20240.8467ex29359090265-(2-Fluorophenyl)-1-(pyridin-3-ylsulfonyl)-1H-pyrrole-3-carbaldehyde (CAS RN 881677-11-8) with a purity by weight of 97 % or more0 %-31.12.20270.5261ex2935909027Methyl (3R,5S,6E)-7-{4-(4-fluorophenyl)-6-isopropyl-2-[methyl(methylsulfonyl)amino]pyrimidin-5-yl}-3,5-dihydroxyhept-6-enoate (CAS RN 147118-40-9)0 %-31.12.20260.5894ex2935909028N-Fluorobenzenesulphonimide (CAS RN 133745-75-2)0 %-31.12.20240.8350ex2935909029Vemurafenib (INN) (CAS RN 918504-65-1) with a purity by weight of 98 % or more0 %-31.12.20270.7183ex29359090306-Aminopyridine-2-sulfonamide (CAS RN 75903-58-1)0 %-31.12.20260.8413ex29359090315-(N-3-methylphenyl-sulfonylamido)-(N’,N’’-bis-(3-methylphenyl)-isophthalicacid-diamide) (CAS RN 2375645-78-4) with a purity by weight of 95 % or more0 %-31.12.20270.7677ex29359090334-Chloro-3-pyridinesulphonamide (CAS RN 33263-43-3)0 %-31.12.20240.3564ex2935909035Chlorsulfuron (ISO) (CAS RN 64902-72-3)0 %-31.12.20240.7572ex29359090371,3-Dimethyl-1H-pyrazole-4-sulfonamide (CAS RN 88398-53-2)0 %-31.12.2024

0.7438ex2935909040Venetoclax (INN) (CAS 1257044-40-8)0 %-31.12.20270.5036ex2935909042Penoxsulam (ISO) (CAS RN 219714-96-2)0 %-31.12.20250.6370ex2935909043Oryzalin (ISO) (CAS RN 19044-88-3)0 %-31.12.20240.7928ex29359090444-[2-(7-Methoxy-4,4-dimethyl-1,3-dioxo-3,4-dihydroisoquinolin-2(1H)-yl)ethyl]bezenesulphonamide (CAS RN 33456-68-7) with a purity by weight of 99,5 % or more0 %-31.12.20250.3562ex2935909045Rimsulfuron (ISO) (CAS RN 122931-48-0)0 %-31.12.20240.6242ex2935909047Halosulfuron-methyl (ISO) (CAS RN 100784-20-1) with a purity by weight of 98 % or more0 %-31.12.20240.5451ex2935909048(3R,5S,6E)-7-[4-(4-Fluorophenyl)-2-[methyl(methylsulfonyl)amino]-6-(propan-2-yl)pyrimidin-5-yl]-3,5-dihydroxyhept-6-enoic acid -- 1-[(R)-(4-chlorophenyl)(phenyl)methyl]piperazine (1:1) (CAS RN 1235588-99-4)0 %-31.12.20260.2843ex29359090504,4’-Oxydi(benzenesulphonohydrazide) (CAS RN 80-51-3)0 %-31.12.20240.4636ex29359090532,4-Dichloro-5-sulphamoylbenzoic acid (CAS RN 2736-23-4)0 %-31.12.20240.6777ex2935909054Propoxycarbazone-sodium (ISO) (CAS RN 181274-15-7) with a purity by weight of 95 % or more0 %-31.12.20250.3560ex2935909055Thifensulfuron-methyl (ISO) (CAS RN 79277-27-3)0 %-31.12.20240.6802ex2935909056N-(p-Toluenesulphonyl)-N’-(3-(p-toluenesulphonyloxy)phenyl)urea (CAS RN 232938-43-1)0 %-31.12.20250.6903ex2935909057N-{2-[(phenylcarbamoyl)amino]phenyl}benzenesulphonamide (CAS RN 215917-77-4)0 %-31.12.20250.6664ex2935909059Flazasulfuron (ISO) (CAS RN 104040-78-0) with a purity of 94 % by weight or more0 %-31.12.20250.7676ex29359090604-[(3-Methylphenyl)amino]pyridine-3-sulfonamide (CAS RN 72811-73-5)0 %-31.12.20240.4586ex2935909063Nicosulphuron (ISO) (CAS RN 111991-09-4) of a purity by weight of 91 % or more0 %-31.12.20240.3561ex2935909065Tribenuron-methyl (ISO) (CAS RN 101200-48-0)0 %-31.12.2024 0.5539ex2935909068(2S)-2-Benzyl-N,N-dimethylaziridine-1-sulfonamide (CAS RN 902146-43-4) with purity by weight of 95,5 % or more0 %-31.12.20240.7854ex2935909070(4S)-4-Hydroxy-2-(3-methoxypropyl)-3,4-dihydro-2H-thieno[3,2-e]thiazine-6-sulfonamide-1,1-dioxide (CAS RN 154127-42-1) with a purity by weight of 97 % or more0 %-31.12.20240.3559ex2935909075Metsulfuron-methyl (ISO) (CAS RN 74223-64-6)0 %-31.12.20240.8055ex29359090804-Chloro-3-sulphamoylbenzoic acid (CAS RN 1205-30-7) with a purity by weight of 97 % or more0 %-31.12.20250.2844ex2935909085N-[4-(Isopropylaminoacetyl)phenyl]methanesulphonamide hydrochloride0 %-31.12.20240.3704ex2935909088N-(2-(4-Amino-N-ethyl-m-toluidino)ethyl)methanesulphonamide sesquisulphate monohydrate (CAS RN 25646-71-3)0 %-31.12.20240.4048ex29359090893-(3-Bromo-6-fluoro-2-methylindol-1-ylsulphonyl)-N,N-dimethyl-1,2,4-triazol-1-sulphonamide (CAS RN 348635-87-0)0 %-31.12.20260.4944ex2938903010Ammonium glycyrrhizate (CAS RN 53956-04-0)0 %-31.12.20250.3554ex2938909010Hesperidin (CAS RN 520-26-3)0 %-31.12.20240.5927ex2938909020Ethylvanillin beta-D-glucopyranoside (CAS RN 122397-96-0)0 %-31.12.20240.7329ex2938909030Rebaudioside A (CAS RN 58543-16-1)0 %-31.12.20270.8178ex29397990501-Alpha-H,5-alpha-H-Nortropan-3-alpha-ol (CAS RN 538-09-0) with a purity by weight of 99 % or more0 %-31.12.20260.7456ex29397990604-Methyl-2-pyridylamine (CAS RN 695-34-1) with a purity by weight of 98 % or more0 %-31.12.20240.7047ex2940000030D(+)- Trehalose dihydrate (CAS RN 6138-23-4)0 %-31.12.20260.7757ex29400000502,3,4,6-Tetrakis-O-(phenylmethyl)-D-galactopyranose (CAS RN 6386-24-9)0 %-31.12.20240.8424ex2940000060Methyl α-D-mannopyranoside (CAS RN 617-04-9) with a purity by weight of 98 % or more0 %-31.12.20270.5233ex2941203010Dihydrostreptomycin sulphate (CAS RN 5490-27-7)0 %-31.12.20260.6984ex2942000010Sodium triacetoxyborohydride (CAS RN 56553-60-7)0 %-31.12.2026

0.355532012000Wattle extract0 %-31.12.20240.7943ex3201902010Rhus chinensis gall (Galla chinensis) water-based extract, with a tannin content by weight of 85 % or less0 %-31.12.20250.3553ex3201909020Tanning extracts derived from gambier and myrobalan fruits0 %-31.12.20240.6183ex3204110015Colourant C.I. Disperse Blue 360 (CAS RN 70693-64-0) and preparations based thereon with a colourant C.I. Disperse Blue 360 content of 99 % or more by weight0 %-31.12.20240.6277ex3204110025N-(2-Chloroethyl)-4-[(2,6-dichloro-4-nitrophenyl)azo]-N-ethyl-m-toluidine (CAS RN 63741-10-6)0 %-31.12.20240.5134ex3204110045 Preparation of dispersion dyes, containing: C.I. Disperse Orange 61 (CAS RN 12270-45-0) or Disperse Orange 288 (CAS RN 96662-24-7), C.I. Disperse Blue 291:1 (CAS RN 872142-01-3), C.I. Disperse Violet 93:1 (CAS RN 122463-28-9), whether or not containing C.I. Disperse Red 54 (CAS RN 6657-37-0) 0 %-31.12.20250.5264ex3204110050Colourant C.I. Disperse Blue 72 (CAS RN 81-48-1) and preparations based thereon with a colourant C.I. Disperse Blue 72 content of 95 % or more by weight0 %-31.12.20270.6972ex3204120015Colourant C.I. Acid Brown 75 (CAS RN 8011-86-7) and preparations based thereon with a colourant C.I. Acid Brown 75 content of 75 % or more by weight0 %-31.12.20260.6975ex3204120017Colourant C.I. Acid Brown 355 (CAS RN 84989-26-4 or 60181-77-3) and preparations based thereon with a colourant C.I. Acid Brown 355 content of 75 % or more by weight0 %-31.12.20260.7021ex3204120025Colourant C.I. Acid Black 210 (CAS RN 85223-29-6 or 99576-15-5) and preparations based thereon with a colourant C.I. Acid Black 210 content of 50 % or more by weight0 %-31.12.20260.6976ex3204120027Colourant C.I. Acid Brown 425 (CAS RN 75234-41-2 or 119509-49-8) and preparations based thereon with a colourant C.I. Acid Brown 425 content of 75 % or more by weight0 %-31.12.20260.6963ex3204120035Colourant C.I. Acid Black 234 (CAS RN 157577-99-6) and preparations based thereon with a colourant C.I. Acid Black 234 content of 75 % or more by weight0 %-31.12.2026 0.6964ex3204120037Colourant C.I. Acid Black 210 sodium salt (CAS RN 201792-73-6) and preparations based thereon with a colourant C.I. Acid Black 210 sodium salt content of 50 % or more by weight0 %-31.12.20260.5925ex3204120040Liquid dye preparation containing anionic acid dye C.I. Acid Blue 182 (CAS RN 12219-26-0)0 %-31.12.20240.6965ex3204120045Colourant C.I. Acid Blue 161/193 (CAS RN 12392-64-2) and preparations based thereon with a colourant C.I. Acid Blue 161/193 content of 75 % or more by weight0 %-31.12.20260.6971ex3204120047Colourant C.I. Acid Brown 58 (CAS RN 70210-34-3 or 12269-87-3) and preparations based thereon with a colourant C.I. Acid Brown 58 content of 75 % or more by weight0 %-31.12.20260.6973ex3204120055Colourant C.I. Acid Brown 165 (CAS RN 61724-14-9) and preparations based thereon with a colourant C.I. Acid Brown 165 content of 75 % or more by weight0 %-31.12.20260.6974ex3204120057Colourant C.I. Acid Brown 282 (CAS RN 70236-60-1 or 12219-65-7) and preparations based thereon with a colourant C.I. Acid Brown 282 content of 75 % or more by weight0 %-31.12.20260.6535ex3204120060Colourant C.I. Acid Red 52 (CAS RN 3520-42-1 ) and preparations based thereon with a colourant C.I. Acid Red 52 content of 97 % or more by weight0 %-31.12.20240.6977ex3204120065Colourant C.I. Acid Brown 432 (CAS RN 119509-50-1) and preparations based thereon with a colourant C.I. Acid Brown 432 content of 75 % or more by weight0 %-31.12.20260.6652ex3204120070Colourant C.I. Acid blue 25 (CAS RN 6408-78-2) and preparations based thereon with a colourant C.I. Acid blue 25 content of 80 % or more by weight0 %-31.12.20250.4065ex3204130010Colourant C.I. Basic Red 1 (CAS RN 989-38-8) and preparations based thereon with a colourant C.I. Basic Red 1 content of 50 % or more by weight0 %-31.12.20240.7394ex3204130015Colourant C.I. Basic Blue 41 (CAS RN 12270-13-2) and preparations based thereon with a colourant C.I. Basic Blue 41 content of 50 % or more by weight0 %-31.12.2027

0.5804ex3204130030Colourant C.I. Basic Blue 7 (CAS RN 2390-60-5) and preparations based thereon with a colourant C.I. Basic Blue 7 content of 50 % or more by weight0 %-31.12.20240.7396ex3204130035Colourant C.I. Basic Yellow 28 (CAS RN 54060-92-3) and preparations based thereon with a colourant C.I. Basic Yellow 28 content of 50 % or more by weight0 %-31.12.20270.5805ex3204130040Colourant C.I. Basic Violet 1 (CAS RN 603-47-4 or CAS RN 8004-87-3) and preparations based thereon with a colourant C.I. Basic Violet 1 content of 90 % or more by weight0 %-31.12.20270.6474ex3204130050Colourant C.I Basic Violet 11 (CAS RN 2390-63-8) and preparations based thereon with a colourant C.I Basic Violet 11 content of 90 % or more by weight0 %-31.12.20240.7775ex3204130055Colourant C.I. Basic Violet 16 (CAS RN 6359-45-1) and preparations based thereon with a colourant C.I. Basic Violet 16 content of 60 % or more by weight0 %-31.12.20240.6475ex3204130060Colourant C.I Basic Red 1:1 (CAS RN 3068-39-1) and preparations based thereon with a colourant C.I Basic Red 1:1 content of 90 % or more by weight0 %-31.12.20240.7776ex3204130065Colourant C.I. Basic Blue 3 (CAS RN 33203-82-6) and preparations based thereon with a colourant C.I. Basic Blue 3 (CAS RN 33203-82-6) content of 50 % or more but not more than 80 % by weight0 %-31.12.20240.7777ex3204130070Mixture of the colourants C.I. Basic Yellow 28 (CAS RN 54060-92-3), C.I. Basic Red 46 (CAS RN 12221-69-1) and C.I. Basic Blue 159 (CAS RN 105953-73-9) and preparations based thereon with a content of colourants C.I. Basic Yellow 28, C.I. Basic Red 46 and C.I. Basic Blue 159 taken together of 60 % or more by weight0 %-31.12.20240.7778ex3204130075Colourant C.I. Basic Red 18:1 (CAS RN 12271-12-4) and preparations based thereon with a content of 40 % or more by weight0 %-31.12.20240.7779ex3204130080Colourant C.I. Basic Yellow (CAS RN 83949-75-1) and preparations based thereon with a content of 40 % or more by weight0 %-31.12.2024 0.6569ex3204140010Colourant C.I. Direct Black 80 (CAS RN 8003-69-8) and preparations based thereon with a colourant C.I. Direct Black 80 content of 90 % or more by weight0 %-31.12.20240.6570ex3204140020Colourant C.I. Direct Blue 80 (CAS RN 12222-00-3) and preparations based thereon with a colourant C.I. Direct Blue 80 content of 90 % or more by weight0 %-31.12.20240.6571ex3204140030C.I. Colourant Direct Red 23 (CAS RN 3441-14-3 ) and preparations based thereon with a colourant C.I. Direct Red 23 content of 90 % or more by weight0 %-31.12.20240.8537ex3204150015Colourant C.I. Vat Blue 1 (CAS RN 482-89-3) and preparations based thereon with a colourant C.I. Vat Blue 1 content of 94 % or more by weight0 %-31.12.20280.3997ex3204150060Colourant C.I. Vat Blue 4 (CAS RN 81-77-6) and preparations based thereon with a colourant C.I. Vat Blue 4 content of 50 % or more by weight0 %-31.12.20240.6129ex3204150070Colourant C.I. Vat Red 1 (CAS RN 2379-74-0)0 %-31.12.20240.6325ex3204160030 Preparations based on Colourant Reactive Black 5 (CAS RN 17095-24-8) with a content thereof of 60 % or more but not more than 75 % by weight, and including one or more of the following:

Colourant Reactive Yellow 201 (CAS RN 27624-67-5), 1-Naphthalenesulphonicacid,4-amino-3-[[4-[[2-(sulphooxy)ethyl]sulphonyl]phenyl]azo]-, disodium salt (CAS RN 250688-43-8), or 3,5-diamino-4-[[4-[[2-(sulphooxy)ethyl]sulphonyl]fenyl]azo]-2-[[2-sulfo-4-[[2-(sulphooxy)ethyl]sulfonyl]phenyl]azobenzoic acid sodium salt (CAS RN 906532-68-1) 0 %-31.12.20240.7367ex3204160040 Aqueous solution of Colourant C.I. Reactive Red 141 (CAS RN 61931-52-0) with a colourant C.I. Reactive Red 141 content of 13 % or more by weight, and containing a preservative 0 %-31.12.2027 0.2517ex3204170010Colourant C.I. Pigment Yellow 81 (CAS RN 22094-93-5) and preparations based thereon with a colourant C.I. Pigment Yellow 81 content of 50 % or more by weight0 %-31.12.20240.5433ex3204170015Colourant C.I. Pigment Green 7 (CAS RN 1328-53-6) and preparations based thereon with a colourant C.I. Pigment Green 7 content of 40 % or more by weight0 %-31.12.20260.7092ex3204170018Colourant C.I. Pigment Orange 16 (CAS RN 6505-28-8) and preparations based thereon with a colourant C.I. Pigment Orange 16 content of 90 % or more by weight0 %-31.12.20260.6130ex3204170019Colourant C.I. Pigment Red 48:2 (CAS RN 7023-61-2) and preparations based thereon with a colourant C.I. Pigment Red 48:2 content of 85 % or more by weight0 %-31.12.20240.5505ex3204170020Colourant C.I. Pigment Blue 15:3 (CAS RN 147-14-8) and preparations based thereon with a colourant C.I. Pigment Blue 15:3 content of 35 % or more by weight0 %-31.12.20260.6279ex3204170021Colourant C.I. Pigment Blue 15:4 (CAS RN 147-14-8) and preparations based thereon with a colourant C.I. Pigment Blue 15:4 content of 35 % or more by weight0 %-31.12.20240.5259ex3204170022Colourant C.I. Pigment Red 169 (CAS RN 12237-63-7) and preparations based thereon with a colourant C.I. Pigment Red 169 content of 50 % or more by weight0 %-31.12.20260.6246ex3204170023Colourant C.I. Pigment Brown 41 (CAS RN 211502-16-8 or CAS RN 68516-75-6)0 %-31.12.20240.6453ex3204170024Colourant C.I. Pigment Red 57:1 (CAS RN 5281-04-9) and preparations based thereon with a Colourant C.I. Pigment Red 57:1 content of 20 % or more by weight0 %-31.12.20240.5427ex3204170025Colourant C.I. Pigment Yellow 14 (CAS RN 5468-75-7) and preparations based thereon with a colourant C.I. Pigment Yellow 14 content of 25 % or more by weight0 %-31.12.20260.7261ex3204170026Colourant C.I. Pigment Orange 13 (CAS RN 3520-72-7) and preparations based thereon with a colourant C.I. Pigment Orange 13 content of 80 % or more by weight0 %-31.12.2027 0.7659ex3204170031Colourant C.I. Pigment Red 63:1 (CAS RN 6417-83-0) and preparations based thereon with a colourant C.I. Pigment Red 63:1 content of 70 % or more by weight0 %-31.12.20240.6603ex3204170033Colourant C.I. Pigment Blue 15:1 (CAS RN 147-14-8) and preparations based thereon with a colourant C.I. Pigment Blue 15:1 content of 35 % or more by weight0 %-31.12.20250.5426ex3204170035Colourant C.I. Pigment Red 202 (CAS RN 3089-17-6) and preparations based thereon with a colourant C.I. Pigment Red 202 content of 70 % or more by weight0 %-31.12.20260.7565ex3204170037Colourant C.I. Pigment Red 81:2 (CAS RN 75627-12-2) and preparations based thereon with a colourant C.I. Pigment Red 81:2 content of 30 % or more by weight0 %-31.12.20240.4630ex3204170040Colourant C.I. Pigment Yellow 120 (CAS RN 29920-31-8) and preparations based thereon with a colourant C.I. Pigment Yellow 120 content of 50 % or more by weight0 %-31.12.20240.6452ex3204170048

Preparation, in the form of extruded beads, containing by weight: 60 % or more but not more than 70 % of Colourant C.I. Pigment Yellow 174 (CAS RN 78952-72-4), 30 % or more, but not more than 40 % disproportionated rosin (CAS RN 8050-09-7), whether or not containing kaolin 0 %-31.12.20250.5832ex3204170075Colourant C.I. Pigment Orange 5 (CAS RN 3468-63-1) and preparations based thereon with a colourant C.I. Pigment Orange 5 content of 80 % or more by weight0 %-31.12.20270.5700ex3204170085Colourant C.I. Pigment Blue 61 (CAS RN 1324-76-1) and preparations based thereon with a colourant C.I. Pigment Blue 61 content of 35 % or more by weight0 %-31.12.20270.5680ex3204170088Colourant C.I. Pigment Violet 3 (CAS RN 1325-82-2 or CAS RN 101357-19-1) and preparations based thereon with a colourant C.I. Pigment Violet 3 content of 90 % or more by weight0 %-31.12.20270.6979ex3204190013Colourant C.I. Sulphur Black 1 (CAS RN 1326-82-5) and preparations based thereon with a colourant C.I. Sulphur Black 1 content of 75 % or more by weight0 %-31.12.2026 0.6406ex3204190014 Red colourant preparation, in a form of wet paste, containing by weight: 35 % or more but not more than 40 % of 1-[[4-(phenylazo)phenyl]azo]naphthalen-2-ol methyl derivatives (CAS RN 70879-65-1) not more than 3 % of 1-(phenylazo)naphthalen-2-ol (CAS RN 842-07-9) not more than 3 % of 1-[(2-methylphenyl)azo]naphthalen-2-ol (CAS RN 2646-17-5) 55 % or more but not more than 65 % of water 0 %-31.12.20240.5100ex3204190073Colourant C.I. Solvent Blue 104 (CAS RN 116-75-6) and preparations based thereon with a colourant C.I. Solvent Blue 104 content of 97 % or more by weight0 %-31.12.20260.5282ex3204190077Colourant C.I. Solvent Yellow 98 (CAS RN 27870-92-4 or CAS RN 12671-74-8) and preparations based thereon with a colourant C.I. Solvent Yellow 98 content of 95 % or more by weight0 %-31.12.20260.4058ex3204200010Colourant C.I. Fluorescent Brightener 184 (CAS RN 7128-64-5) and preparations based thereon with a colourant C.I. Fluorescent Brightener 184 content of 20 % or more by weight0 %-31.12.20260.5395ex3204200030Colourant C.I. Fluorescent Brightener 351 (CAS RN 27344-41-8) and preparations based thereon with a colourant C.I. Fluorescent Brightener 351 content of 90 % or more by weight0 %-31.12.20260.6473ex3204900010Colourant C.I Solvent Yellow 172 (also known as C.I. Solvent Yellow 135) (CAS RN 68427-35-0) and preparations based thereon with a colourant C.I Solvent Yellow 172 (also known as C.I. Solvent Yellow 135) content of 90 % or more by weight0 %-31.12.20240.3707ex3205000010Aluminium lakes prepared from dyes for use in the manufacture of pigments for the pharmaceutical industry0 %-31.12.20240.7658ex3205000020 Colourant C.I. Solvent Red 48 (CAS RN 13473-26-2) preparation, in a form of dry powder, containing by weight: 16 % or more but not more than 25 % of Colourant C.I. Solvent Red 48 (CAS RN 13473-26-2) 65 % or more but not more than 75 % of aluminium hydroxide (CAS RN 21645-51-2) 0 %-31.12.2024 0.7699ex3205000030

Colourant C.I. Pigment Red 174 (CAS RN 15876-58-1) preparation, in a form of dry powder, containing by weight: 16 % or more but not more than 21 % of Colourant C.I. Pigment Red 174 (CAS RN 15876-58-1) 65 % or more but not more than 69 % of aluminium hydroxide (CAS RN 21645-51-2) 0 %-31.12.20240.3550ex3206110010Titanium dioxide coated with isopropoxytitanium triisostearate, containing by weight 1,5 % or more but not more than 2,5 % of isopropoxytitanium triisostearate0 %-31.12.20240.5378ex3206190010 Preparation containing by weight: 72 % (± 2 %) of mica (CAS RN 12001-26-2), and 28 % (± 2 %) of titanium dioxide (CAS RN 13463-67-7) 0 %-31.12.20260.3551ex3206420010Lithopone (CAS RN 1345-05-7)0 %-31.12.20240.6245ex3206497020Colourant C.I. Pigment Blue 27 (CAS RN 14038-43-8)0 %-31.12.20240.7390ex3206497040Colourant C.I. Pigment Blue 27 (CAS RN 25869-00-5) and preparations thereon with a colourant C.I. Pigment Blue 27 content of 85 % or more by weight0 %-31.12.20270.8211ex3206497050 Concentrated mixture of pigments (masterbatch) in the form of pellets containing by weight: 50 % or more but not more than 70 % of polyamide–6,6 (CAS RN 32131-17-2), 15 % or more but not more than 20 % of iron powder (CAS RN 7439-89-6), 5 % or more but not more than 15 % of barium sulphate (CAS RN 7727-43-7), and 5 % or more but not more than 10 % of blue pigment, consisting of a mixture of Titanium dioxide (CAS RN 13463-67-7) and Copper(II) phtalocyanine(CAS RN 147-14-8) 0 %-31.12.20260.367332065000Inorganic products of a kind used as luminophores0 %-31.12.20240.6233ex3207300020 Printing paste containing 30 % by weight or more, but not more than 50 % of silver and 8 % by weight or more, but not more than 17 % of palladium 0 %-31.12.2024 0.2511ex3208201010Copolymer of N-vinylcaprolactam, N-vinyl-2-pyrrolidone and dimethylaminoethyl methacrylate, in the form of a solution in ethanol containing by weight 34 % or more but not more than 40 % of copolymer0 %-31.12.20240.4511ex3208201020Immersion topcoat solution containing by weight 0,5 % or more but not more than 15 % of acrylate-methacrylate-alkenesulphonate copolymers with fluorinated side chains, in a solution of n-butanol and/or 4-methyl-2-pentanol and/or diisoamylether0 %-31.12.20240.8412 ex32082010 ex39059100 50 25 Copolymer of vinylcaprolactam and vinylpyrrolidone (CAS RN 51987-20-3) in the form of a solution in 2-butoxyethanol (CAS RN 111-76-2) containing by weight 45 % or more but not more than 58 % of copolymer0 %-31.12.20270.8137 ex32089019 ex39119099 13 63 Mixture, containing by weight: 20 % or more but not more than 40 % of a copolymer of methyl vinyl ether and monobutyl maleate (CAS RN 25119-68-0), 7 % or more but not more than 20 % of a copolymer of methyl vinyl ether and monoethyl maleate (CAS RN 25087-06-3), 40 % or more, but not more than 65 % of ethanol (CAS RN 64-17-5), 1 % or more but not more than 7 % of butan-1-ol (CAS RN 71-36-3) 0 %-31.12.20250.3967ex3208901915Chlorinated polyolefins, in a solution0 %-31.12.20240.2504ex3208901940Polymer of methylsiloxane, in the form of a solution in a mixture of acetone, butanol, ethanol and isopropanol, containing by weight 5 % or more but not more than 11 % of polymer of methylsiloxane0 %-31.12.20240.6154

ex32089019 ex38249992 45 63 Polymer consisting of a polycondensate of formaldehyde and naphthalenediol, chemically modified by reaction with an alkyne halide, dissolved in propylene glycol methyl ether acetate0 %-31.12.20240.6989ex3208901947 Solution containing by weight: 0.1 % or more but not more than 20 % of alkoxygroups containing siloxane polymer with alkyl or aryl substituents 75 % or more of an organic solvent containing one or more of propyleneglycolethylether (CAS RN 1569-02-4), propylene glycol mono methylether acetate (CAS RN 108-65-6) or propyleneglycol propylether (CAS RN 1569-01-3) 0 %-31.12.2026 0.2502ex3208901950 Solution containing by weight: (65 ± 10) % of γ-butyrolactone, (30 ± 10) % of polyamide resin, (3,5 ± 1,5) % of naphthoquinone ester derivative and (1,5 ± 0,5) % of arylsilicic acid 0 %-31.12.20240.6726ex3208901955Preparation of 5 % or more but not more than 20 % by weight of a copolymer of propylene and maleic anhydride, or a blend of polypropylene and a copolymer of propylene and maleic anhydride, or a blend of polypropylene and a copolymer of propylene, isobutene and maleic anhydride in an organic solvent0 %-31.12.20260.4037ex3208901960 Copolymer of hydroxystyrene with one or more of the following: styrene alkoxystyrene alkylacrylates dissolved in ethyl lactate 0 %-31.12.20260.6005ex3208901965Silicones containing 50 % by weight or more of xylene and not more than 25 % by weight of silica, of a kind used for the manufacture of long term surgical implants0 %-31.12.20240.5777ex3215190020 Ink: consisting of a polyester polymer and a dispersion of silver (CAS RN 7440-22-4) and silver chloride (CAS RN 7783-90-6) in methyl propyl ketone (CAS RN 107-87-9), with a total solid content by weight of 55 % or more, but not more than 57 %, and with a specific density of 1,40 g/cm3 or more, but not more than 1,60 g/cm3, for use in the manufacture of electrodes 0 %l31.12.20270.2506ex3215907010Ink formulation, for use in the manufacture of ink-jet cartridges0 %-31.12.20240.2501ex3215907020Heat sensitive ink fixed on a plastic film0 %-31.12.20240.4533ex3215907030 Disposable cartridge ink, containing by weight: 1 % or more, but not more than 10 % of amorphous silicon dioxide or 3,8 % or more of dye C.I. Solvent Black 7 in organic solvents for use in the marking of integrated circuits 0 %-31.12.2024 0.5031ex3215907040 Dry ink powder with a base of hybrid resin (made from polystyrene acrylic resin and polyester resin) mixed with: wax a vinyl-based polymer and a colouring agent for use in the manufacture of toner bottles for photocopiers, fax machines, printers and multifunction devices 0 %-31.12.20250.366133011210Essential oil of orange, not deterpenated0 %-31.12.20240.4863ex3402399010Sodium lauroyl methyl isethionate0 %-31.12.20260.4002ex3402420010Vinyl copolymer surface active agent based on polypropylene glycol0 %-31.12.20240.4277ex3402420020Surfactant containing 1,4-dimethyl-1,4-bis(2-methylpropyl)-2-butyne-1,4-diyl ether, polymerised with oxirane, methyl terminated0 %-31.12.20270.6285ex3402901010Surface-active mixture of methyltri-C8-C10-alkylammonium chlorides0 %-31.12.20240.3660ex3402901020Mixture of docusate sodium (INN) and sodium benzoate0 %-31.12.20240.4676ex3402901070Surface-active preparation, containing ethoxylated 2,4,7,9-tetramethyl-5-decyne-4,7-diol (CAS RN 9014-85-1)0 %-31.12.20240.7508ex3501909010Non edible sodium caseinate (CAS RN 9005-46-3) in the form of powder with a protein content of more than 88 % by weight for use in the production of thermoplastic granules0 %-31.12.20240.2498ex3506919010Adhesive based on an aqueous dispersion of a mixture of dimerised rosin and a copolymer of ethylene and vinyl acetate (EVA)0 %-31.12.20240.4003ex3506919030Two component microencapsulated epoxy adhesive dispersed in a solvent0 %-31.12.20240.4313ex3506919040Acrylic pressure sensitive adhesive with a thickness of 0,076 mm or more but not more than 0,127 mm, put up in rolls of a width of 45,7 cm or more but not more than 132 cm supplied on a release liner with an initial peel adhesion release value of not less than 15 N/25 mm (measured according to ASTM D3330)0 %-31.12.2024

0.6725ex3506919050 Preparation containing by weight: 15 % or more but not more than 60 % of styrene butadiene copolymers or styrene isoprene copolymers, and 10 % or more but not more than 30 % of pinene polymers or pentadiene copolymers, dissolved in: Methyl ethyl ketone (CAS RN 78-93-3), Heptane (CAS RN 142-82-5), and Toluene (CAS RN 108-88-3) or light aliphatic solvent naphtha (CAS RN 64742-89-8) 0 %-31.12.20240.6293ex3507909010Preparation of Achromobacter lyticus protease (CAS RN 123175-82-6) for use in the manufacture of human and analogue insulin products0 %-31.12.20240.7050ex3507909030 Salicylate 1-monooxygenase (CAS RN 9059-28-3) in aqueous solution with an enzyme concentration of 6,0 U/ml or more, but not more than 7,4 U/ml , a concentration by weight of sodium azide (CAS RN 26628-22-8) of not more than 0,09 % and a pH value of 6,5 or more, but not more than 8,5 0 %-31.12.20260.4922ex3601000020Pyrotechnical mixture in cylindrical shape or granulate form, composed of strontium nitrate or copper nitrate or basic copper nitrate in a matrix of nitroguanidine or guanidine nitrate, also containing a binder and additives, used as a component of airbag inflators0 %-31.12.20260.7318ex3603500010Igniters for gas generators with an overall maximum length of 20,34 mm or more but not more than 29,4 mm and a pin length of 6,68 mm (± 0,3 mm) or more but not more than 7,54 mm (± 0,3 mm)0 %-31.12.20270.7994ex3801100020 Artificial graphite (CAS RN 7782-42-5) powder form, with: specific surface area (measured by BET) of 0,8 m2/g (± 0,25), tap density: 0,85 g/cm3 (± 0,10), particle size represented by d50 value of 21,0 µm (± 2,0), specific discharge capacity of 351,0 mAh/g (± 3,0), initial efficiency of 94,0 % (± 2,0) 1,8 %-31.12.2024 0.7975ex3801100030 Artificial graphite in powder form, (CAS RN 7782-42-5) with: with or without coating on the surface, particle size represented by d50 value of 15 µm (± 4), specific surface area (measured by BET) less than 3,5 m2/g, tap density: 1,3 g/m3 (± 0,5), specific Discharge Capacity of 348 mAh/g (± 13), initial efficiency above 93,0 % 1,8 %-31.12.20240.5465ex3801900010Expandable graphite (CAS RN 90387-90-9 and CAS RN 12777-87-6)0 %-31.12.20260.6759ex3802100010Mixture of activated carbon and polyethylene, in form of powder0 %-31.12.20250.7368ex3802100040Chemically activated carbon for the absorption and desorption of vapors, in a defined or irregular shape with an effective butane capacity of 5 g butane / 100 ml or more (according to ASTM D 5228)0 %-31.12.20270.298738059010Pine oil1,7 %-31.12.20240.2990ex3808919010Indoxacarb (ISO) and its (R) isomer, fixed on a support of silicon dioxide0 %-31.12.20240.2988ex3808919030 Preparation containing endospores or spores and protein crystals derived from either: Bacillus thuringiensis Berliner subsp. aizawai and kurstaki or, Bacillus thuringiensis subsp. kurstaki or, Bacillus thuringiensis subsp. israelensis or, Bacillus thuringiensis subsp. aizawai or, Bacillus thuringiensis subsp. tenebrionis

0 %-31.12.20240.2983ex3808919040Spinosad (ISO)0 %-31.12.20240.5710ex3808919060Spinetoram (ISO) (CAS RN 935545-74-7), preparation of two spinosyn components (3’-ethoxy–5,6-dihydro spinosyn J) and (3’-ethoxy- spinosyn L)0 %-31.12.20270.6874ex3808923010Mancozeb (ISO) (CAS RN 8018-01-7) imported in immediate packings of a content of 500 kg or more0 %-31.12.20250.2986ex3808929010Fungicide in the form of a powder, containing by weight 65 % or more but not more than 75 % of hymexazole (ISO), not put up for retail sale0 %-31.12.2024 0.2984ex3808929030 Preparation consisting of a suspension of pyrithione zinc (INN) in water, containing by weight: 24 % or more but not more than 26 % of pyrithione zinc (INN), or 39 % or more but not more than 41 % of pyrithione zinc (INN) 0 %-31.12.20240.4843ex3808929050Preparations based on copper pyrithione (CAS RN 14915-37-8)0 %-31.12.20240.4753ex3808939010 Preparation, in the form of granules, containing by weight: 38,8 % or more but not more than 41,2 % of Gibberellin A3, or 9,5 % or more but not more than 10,5 % of Gibberellin A4 and A7 0 %-31.12.20240.5048ex3808939020 Preparation consisting of benzyl(purin-6-yl)amine in a glycol solution, containing by weight: 1,88 % or more but not more than 2,00 % of benzyl(purin-6-yl)amine of a kind used in plant growth regulators 0 %-31.12.20250.6532ex3808942030 Bromochloro-5,5-dimethylimidazolidine-2,4-dione (CAS RN 32718-18-6) containing: 1,3-Dichloro-5,5-dimethylimidazolidine-2,4-dione (CAS RN 118-52-5), 1,3-Dibromo-5,5-dimethylimidazolidine-2,4-dione (CAS RN 77-48-5), 1-Bromo,3-chloro-5,5-dimethylimidazolidine-2,4-dione (CAS RN 16079-88-2), and/or 1-Chloro,3-bromo-5,5-dimethylimidazolidine-2,4-dione (CAS RN 126-06-7) 0 %-31.12.20240.2557ex3809910010Mixture of 5-ethyl-2-methyl-2-oxo-1,3,2λ5-dioxaphosphoran-5-ylmethyl methyl methylphosphonate and bis(5-ethyl-2-methyl-2-oxo-1,3,2λ5-dioxaphosphoran-5-ylmethyl) methylphosphonate0 %-31.12.20240.4406ex3810100010 Soldering or welding paste, consisting of a mixture of metals and resin containing by weight: 70 % or more, but not more than 90 % of tin not more than 10 % of one or more metals of silver, copper, bismuth, zinc, or indium for use in the electro technical industry 0 %-31.12.2024 0.4510ex3811190010 Solution of more than 61 % but not more than 63 % by weight of methylcyclopentadienyl manganese tricarbonyl in an aromatic hydrocarbon solvent, containing by weight not more than: 4,9 % of 1,2,4-trimethyl-benzene, 4,9 % of naphthalene, and 0,5 % of 1,3,5-trimethyl-benzene 0 %-31.12.20240.3448ex3811210010Salts of dinonylnaphthalenesulphonic acid, in the form of a solution in mineral oils0 %-31.12.20240.7223ex3811210011 Dispersing agent and oxidation inhibitor containing: o-amino polyisobutylenephenol (CAS RN 78330-13-9), more than 30 % by weight but not more than 50 % by weight of mineral oils, used in the manufacture of blends of additives for lubricating oils 0 %-31.12.20240.6904ex3811210012 Dispersing agent containing: esters of polyisobutenyl succinic acid and pentaerythritol (CAS RN 103650-95-9),

35 % or more but not more than 55 % by weight of mineral oils, and with a chlorine content of not more than 0,05 % by weight, used in the manufacture of blends of additives for lubricating oils 0 %-31.12.20250.6018ex3811210013 Additives containing: borated magnesium (C16-C24) alkylbenzene sulphonates and mineral oils, having a total base number (TBN) of more than 250, but not more than 350, for use in the manufacture of lubricating oils 0 %-31.12.20240.6906ex3811210014 Dispersing agent: containing polyisobutene succinimide derived from reaction products of polyethylenepolyamines with polyisobutenyl succinic anhydride (CAS RN 147880-09-9), containing 35 % or more but not more than 55 % by weight of mineral oils, with a chlorine content by weight of not more than 0,05 %, having a total base number of less than 15, used in the manufacture of blends of additives for lubricating oils 0 %-31.12.2025 0.6907ex3811210016 Detergent containing: Calcium salt of beta-aminocarbonyl alkylphenol (reaction product Mannich base of alkylphenol) 40 % or more but not more than 60 % by weight of mineral oils and having a total base number more than 120 used in the manufacture of blends of additives for lubricating oils 0 %-31.12.20250.6905ex3811210018 Detergent containing: long chain alkyltoluene calcium sulphonates, more than 30 % but not more than 50 % by weight of mineral oils, and having a total base number of more than 310 but not more than 340, used in the manufacture of blends of additives for lubricating oils 0 %-31.12.20250.6430ex3811210019 Additives containing: a polyisobutylene succinimide based mixture, and more than 30 % but not more than 50 % by weight of mineral oils, having a total base number of more than 40, for use in the manufacture of lubricating oils 0 %-31.12.20240.3449ex3811210020Additives for lubricating oils, based on complex organic molybdenum compounds, in the form of a solution in mineral oil0 %-31.12.20240.8583ex3811210021 Additive containing by weight: 90 % or more but not more than 97 % of reaction products of butyl-cyclohex-3-enecarboxylate and sulphur (CAS RN 160305-95-3), 3 % or more but not more than 10 % of mineral oil, for use in the manufacture of blends of additives for lubricating oils 0 %-31.12.20280.8196ex3811210022 Additive consisting essentially of: Polyisobutenyl succinic anhydride (CAS RN 192662-34-3) reaction product with N,N-diethylaminoethanol (CAS RN 100-37-8), 25 % or more by weight, but not more than 40 % by weight of mineral oil, used in the manufacture of blends of additives for lubricating oils 0 %-31.12.2026 0.8197ex3811210024 Additive consisting essentially of: Polyisobutenyl succinic anhydride reaction product with polyethylenepolyamines, borated (CAS RN 134758-95-5), with a chlorine content by weight of 0,05 % or more but not more than 0,25 % and a total base number (TBN) of more than 20, 45 % and more by weight and no more than 55 % by weight of mineral oil, used in the manufacture of blends of additives for lubricating oils

0 %-31.12.20260.6012ex3811210025 Additives containing: a (C8-18) alkyl polymethacrylate copolymer with N-[3-(dimethylamino)propyl]methacrylamide, of an average molecular weight (Mw) of more than 10000 but not more than 20000, and more than 15 %, but not more than 30 % by weight of mineral oils, for use in the manufacture of lubricating oils 0 %-31.12.20240.8198ex3811210026 Additive consisting essentially of: Phosphorodithioic acid, mixed O,O-bis (1,3-dimethylbutyl and isopropyl) esters, zinc salts (CAS RN 84605-29-8), 7 % or more by weight but not more than 12 % by weight of mineral oil, used in the manufacture of blends of additives for lubricating oils 0 %-31.12.20260.6022ex3811210027 Additives containing: 10 % or more by weight of an ethylene-propylene copolymer chemically modified by succinic anhydride groups reacted with 3-nitroaniline, and mineral oils, for use in the manufacture of lubricating oils 0 %-31.12.2024 0.8199ex3811210028 Additive consisting essentially of: Zinc bis(O,O-bis(2-ethylhexyl)) bis (dithiophosphate) (CAS RN 4259-15-8); triphenyl phosphite (CAS RN 101-02-0) more than 0,5 % by weight but not more than 6 % by weight, O,O,O-triphenyl phosphorothioate (CAS RN 597-82-0) more than 0,5 % by weight but not more than 6 % by weight, and not more than 7,5 % by weight of the combination of triphenylphosphorus compounds 10 % or more by weight but not more than 20 % by weight of mineral oils, used in the manufacture of blends of additives for lubricating oils 0 %-31.12.20260.5717ex3811210030Additives for lubricating oils, containing mineral oils, consisting of calcium salts of reaction products of polyisobutylene substituted phenol with salicylic acid and formaldehyde, used as a concentrated additive for the manufacture of engine oils through a blending process0 %-31.12.20270.8201ex3811210032 Additive consisting essentially of: Zinc O,O,O’,O’-tetrakis (1,3-dimethylbutyl) bis(phosphorodithioate) (CAS RN 2215-35-2), 4 % or more by weight but not more than 12 % by weight of mineral oil, used in the manufacture of blends of additives for lubricating oils 0 %-31.12.20260.6013ex3811210033 Additives containing: calcium salts of heptylphenol reaction products with formaldehyde (CAS RN 84605-23-2), and mineral oils, having a total base number (TBN) of more than 40 but not more than 100, for use in the manufacture of lubricating oils or overbased detergents for use in lubricating oils 0 %-31.12.20240.6016ex3811210037 Additives containing: a styrene-maleic anhydride copolymer esterified with C4-C20 alcohols, modified by aminopropylmorpholine, and more than 50 % but not more than 75 % by weight of mineral oils, for use in the manufacture of lubricating oils 0 %-31.12.2024 0.6435ex3811210048 Additives containing overbased magnesium (C20-C24) alkylbenzenesulphonates (CAS RN 231297-75-9) and by weight more than 25 % but not more than 50 % of mineral oils, having a total base number of more than 350, but not more than 450, for use in the manufacture of lubricating oils

0 %-31.12.20240.5727ex3811210050 Additives for lubricating oils, based on calcium C16-24 alkylbenzenesulphonates (CAS RN 70024-69-0), containing mineral oils, used as a concentrated additive for the manufacture of engine oils through a blending process 0 %-31.12.20270.6437ex3811210053 Additives containing: overbased calcium petroleum sulphonates (CAS RN 68783-96-0) with a sulphonate content by weight of 15 % or more, but not more than 30 % and by weight more than 40 % but not more than 60 % of mineral oils, having a total base number of 280 or more but not more than 420, for use in the manufacture of lubricating oils 0 %-31.12.20240.6434ex3811210055 Additives containing: low base number calcium polypropylbenzenesulphonate (CAS RN 75975-85-8) and by weight more than 40 % but not more than 60 % of mineral oils, having a total base number of more than 10 but not more than 25, for use in the manufacture of lubricating oils 0 %-31.12.20240.5724ex3811210060 Additives for lubricating oils, containing mineral oils, based on calcium polypropylenyl substituted benzenesulphonate (CAS RN 75975-85-8) with a content by weight of 25 % or more but not more than 35 %, with a total base number (TBN) of 280 or more but not more than 320, used as a concentrated additive for the manufacture of engine oils through a blending process 0 %-31.12.2027 0.6431ex3811210063 Additives containing: an overbased mixture of calcium petroleum sulphonates (CAS RN 61789-86-4) and synthetic calcium alkylbenzenesulphonates (CAS RN 68584-23-6 and CAS RN 70024-69-0) with a total sulphonate content by weight of 15 % or more, but not more than 25 % and by weight more than 40 % but not more than 60 % of mineral oils, having a total base number of 280 or more but not more than 320, for use in the manufacture of lubricating oils 0 %-31.12.20240.6429ex3811210065 Additives containing: a polyisobutylene succinimide based mixture (CAS RN 160610-76-4), and more than 35 % but not more than 50 % by weight of mineral oils, having a sulphur content of more than 0,7 % but not more than 1,3 % by weight, having a total base number of more than 8, for use in the manufacture of lubricating oils 0 %-31.12.20240.5711ex3811210070 Additives for lubricating oils, containing polyisobutylene succinimide derived from reaction products of polyethylenepolyamines with polyisobutenyl succinic anhydride (CAS RN 84605-20-9), containing mineral oils, with a chlorine content by weight of 0,05 % or more but not more than 0,25 %, with a total base number (TBN) of more than 20, used as a concentrated additive for the manufacture of engine oils through a blending process 0 %-31.12.20270.6017ex3811210073 Additives containing: borated succinimide compounds (CAS RN 134758-95-5), mineral oils, and having a total base number (TBN) greater than 40, for use in the manufacture of additive mixtures for lubricating oils 0 %-31.12.2024 0.6671ex3811210075 Additives containing: Calcium (C10-C14) dialkylbenzenesulfonates, more than 40 %, but not more than 60 % by weight of mineral oils,

with a total base number of not more than 10, for use in the manufacture of blends of additives for lubricating oils 0 %-31.12.20270.6669ex3811210077 Antifoam additives consisting of: a copolymer of 2-ethylhexyl acrylate and ethyl acrylate, and more than 50 % but not more than 80 % by weight of mineral oils, for use in the manufacture of additive blends for lubricating oils 0 %-31.12.20270.6666ex3811210080 Additives containing: polyisobutylene aromatic polyamine succinimide, more than 40 % but not more than 60 % by weight of mineral oils, with a nitrogen content of more than 0,6 % but not more than 0,9 % by weight, for use in the manufacture of additive blends for lubricating oils 0 %-31.12.20270.6498ex3811210083 Additives containing: polyisobutene succinimide derived from reaction of polyethylenepolyamines with polyisobutenyl succinic anhydride (CAS RN 84605-20-9), more than 31,9 % but not more than 43,3 % by weight of mineral oils, not more than 0,05 % by weight chlorine, and having a total base number (TBN) greater than 20, for use in the manufacture of additives blends for lubricating oils 0 %-31.12.20240.5718ex3811210085 Additives: containing more than 20 % but not more than 45 % by weight of mineral oils, based on a mixture of branched dodecylphenol sulfide calcium salts, whether or not carbonated, for use in the manufacture of blends of additives 0 %-31.12.2027 0.7512ex3811290018Additive consisting of dihydroxy butanedioic acid - (mixed C12-16-alkyl and C13-rich C11-14-isoalkyl) diester, for use in the manufacture of engine oils0 %-31.12.20240.5721ex3811290020Additives for lubricating oils, consisting of reaction products of bis(2-methylpentan-2-yl)dithiophosphoric acid with propylene oxide, phosphorus oxide, and amines with C12-14 alkyl chains, used as a concentrated additive for the manufacture of lubricating oils0 %-31.12.20270.6432ex3811290025Additives containing at least salts of primary amines and mono- and di-alkylphosphoric acids, for use in the manufacture of lubricating oils or greases0 %-31.12.20240.5723ex3811290030Additives for lubricating oils, consisting of reaction products of butyl-cyclohex-3-enecarboxylate, sulphur and triphenyl phosphite (CAS RN 93925-37-2), used as a concentrated additive for the manufacture of engine oils through a blending process0 %-31.12.20270.6433ex3811290035Additives consisting of an imidazoline based mixture (CAS RN 68784-17-8), for use in the manufacture of lubricating oils0 %-31.12.20240.5728ex3811290040Additives for lubricating oils, consisting of reaction products of 2-methyl-prop-1-ene with sulphur monochloride and sodium sulphide (CAS RN 68511-50-2), with a chlorine content by weight of 0,01 % or more but not more than 0,5 %, used as a concentrated additive for the manufacture of lubricating oils0 %-31.12.20270.6436ex3811290045Additives consisting of a mixture of (C7-C9) dialkyl adipates, in which diisooctyl adipate (CAS RN 1330-86-5) is more than 85 % by weight of the mixture, for use in the manufacture of lubricating oils0 %-31.12.20240.5719ex3811290050Additives for lubricating oils, consisting of a mixture of N,N-dialkyl -2-hydroxyacetamides with alkyl chain lengths between 12 and 18 carbon atoms (CAS RN 866259-61-2), used as a concentrated additive for the manufacture of engine oils through a blending process0 %-31.12.2027

0.6020ex3811290070Additives consisting of dialkylphosphites (in which the alkyl groups contain more than 80 % by weight of oleyl, palmityl and stearyl groups), for use in the manufacture of lubricating oils0 %-31.12.20240.7205ex3811290075Oxidation inhibitor mainly containing a mixture of isomers of 1-(tert-dodecylthio)propan-2-ol (CAS RN 67124-09-8), used in the manufacture of blends of additives for lubricating oils0 %-31.12.20240.6023ex3811290085Additives consisting of a mixture of 3-((C9-11)-isoalkyloxy)tetrahydrothiophene 1,1-dioxide, C10-rich (CAS RN 398141-87-2), for use in the manufacture of lubricating oils0 %-31.12.20240.3730ex3811900010Dinonylnaphthylsulphonic acid salt, in a mineral oil solution0 %-31.12.20240.5565ex3811900040Solution of a quaternary ammonium salt based on polyisobutenyl succinimide, containing by weight 10 % or more but not more than 29,9 % of 2-ethylhexanol0 %-31.12.20270.7204ex3811900050 Corrosion inhibitor containing: polyisobutenyl succinic acid and more than 5 % and not more than 20 % by weight of mineral oils for use in the manufacture of blends of additives for fuels 0 %-31.12.20260.5147ex3812100010Rubber accelerator based on diphenyl guanidine granules (CAS RN 102-06-7)0 %-31.12.20260.6045ex3812209010 Plasticiser, containing: bis(2-ethylhexyl)-1,4-benzene dicarboxylate (CAS RN 6422-86-2) more than 10 % but not more than 60 % by weight of dibutylterephthalate (CAS RN 1962-75-0) 0 %-31.12.20240.3444ex3812399020Mixture containing predominantly bis(2,2,6,6-tetramethyl-1-octyloxy-4-piperidyl) sebacate0 %-31.12.2024 0.6055ex3812399025 UV photo stabiliser containing: α-[3-[3-(2H-Benzotriazol-2-yl)-5-(1,1-dimethylethyl)-4-hydroxyphenyl]-1-oxopropyl]-ω-hydroxypoly(oxy-1,2-ethanediyl) (CAS RN 104810-48-2); α-[3-[3-(2H-Benzotriazol-2-yl)-5-(1,1-dimethylethyl)-4-hydroxyphenyl]-1-oxopropyl]-ω-[3-[3-(2H-benzotriazol-2-yl)-5-(1,1-dimethylethyl)-4-hydroxyphenyl]-1-oxopropoxy]poly (oxy-1,2-ethanediyl) (CAS RN 104810-47-1); polyethylene glycol of a weight average molecular weight (Mw) of 300 (CAS RN 25322-68-3) bis (1,2,2,6,6-pentamethyl-4-piperidyl)sebacate (CAS RN 41556-26-7), and methyl-1,2,2,6,6-pentamethyl-4- piperidyl sebacate (CAS RN 82919-37-7) 0 %-31.12.20240.3446ex3812399030Compound stabilisers containing by weight 15 % or more but not more than 40 % of sodium perchlorate and not more than 70 % of 2-(2-methoxyethoxy)ethanol0 %-31.12.20240.6054ex3812399035 Mixture containing by weight: 25 % or more but not more than 55 % of a mixture of C15-18 tetramethylpiperidinyl esters (CAS RN 86403-32-9) not more than 20 % of other organic compounds on a carrier of polypropylene (CAS RN 9003-07-0) or amorphous silica (CAS RN 7631-86-9 or 112926-00-8) 0 %-31.12.20240.4861ex3812399040 Mixture of: 80 % (± 10 %) by weight of 2-ethylhexyl 10-ethyl-4,4-dimethyl-7-oxo-8-oxa-3,5-dithia-4-stannatetradecanoate (CAS RN 57583-35-4), and 20 % (± 10 %) by weight of 2-ethylhexyl 10-ethyl-4-[[2-[(2-ethylhexyl)oxy]-2-oxoethyl]thio]-4-methyl-7-oxo-8-oxa-3,5-dithia-4-stannatetradecanoate (CAS RN 57583-34-3)

0 %-31.12.20240.8273ex38123990452-Aminoethanol reaction products with cyclohexane and peroxidized N-butyl-2,2,6,6-tetramethyl-4-piperidinamine-2,4,6-trichloro-1,3,5-triazine reaction products (CAS RN 191743-75-6) with a purity by weight of 99 % or more0 %-31.12.2026 0.5477ex3812399055 UV-stabilizer, containing: 2-(4,6-bis(2,4-dimethylphenyl)-1,3,5-triazin-2-yl)-5-(octyloxy)-phenol (CAS RN 2725-22-6) and either N,N’-bis(1,2,2,6,6-pentamethyl-4-piperidinyl)-1,6-hexanediamine, polymer with 2,4- dichloro-6-(4-morpholinyl)-1,3,5-triazine (CAS RN 193098-40-7) or N,N’-bis(2,2,6,6-tetramethyl-4-piperidinyl)-1,6-hexanediamine, polymer with 2,4- dichloro-6-(4-morpholinyl)-1,3,5-triazine (CAS RN 82451-48-7) 0 %-31.12.20260.5483ex3812399065 Stabiliser for plastic material containing: 2-ethylhexyl 10-ethyl-4,4-dimethyl-7-oxo-8-oxa-3,5-dithia-4-stannatetradecanoate (CAS RN 57583-35-4), 2-ethylhexyl 10-ethyl-4-[[2-[(2-ethylhexyl)oxy]-2-oxoethyl]thio]-4-methyl-7-oxo-8-oxa-3,5-dithia-4-stannatetradecanoate (CAS RN 57583-34-3), and 2-ethylhexyl mercaptoacetate (CAS RN 7659-86-1) 0 %-31.12.20260.8533ex3812399075 UV stabilizer containing a mixture of: branched and linear C7 to C9 alkyl esters of [3-(2H-benzotriazol-2-yl)-5-(1,1- dimethylethyl)-4-hydroxy]-1- phenylpropanoic acid (CAS RN 127519-17-9) in an amount of 95 % by weight or more, and 2-methoxy-1-methylethyl acetate (CAS RN 108-65-6) in an amount of not more than 5 % by weight 0 %-31.12.20280.5822ex3812399080 UV-stabilizer, consisting of: a hindered amine: N,N’-bis(1,2,2,6,6-pentamethyl-4-piperidinyl)-1,6-hexanediamine, polymer with 2,4-dichloro-6-(4-morpholinyl)-1,3,5-triazine (CAS RN 193098-40-7) and either an o-hydroxyphenyl triazine UV light absorber or a chemically modified phenolic compound 0 %-31.12.20270.3441ex3814009020 Mixture containing by weight: 69 % or more but not more than 71 % of 1-methoxypropan-2-ol (CAS RN 107-98-2), 29 % or more but not more than 31 % of 2-methoxy-1-methylethyl acetate (CAS RN 108-65-6) 0 %-31.12.20240.3731ex3814009040Azeotrope mixtures containing isomers of nonafluorobutyl methyl ether and/or nonafluorobutyl ethyl ether0 %-31.12.2024 0.2800ex3815120010Catalyst, in the form of granules or rings of a diameter of 3 mm or more but not more than 10 mm, consisting of silver on an aluminium oxide support and containing by weight 8 % or more but not more than 40 % of silver0 %-31.12.20240.7574ex3815120020 Spherical catalyst consisting of a support of aluminium oxide coated with platinum, with a diameter of 1,4 mm or more but not more than 2,0 mm, and a platinum content by weight of 0,2 % or more but not more than 0,5 % 0 %-31.12.20240.7585ex3815120030 Catalyst containing 0,3 gram per litre or more, but not more than 7 gram per litre of precious metals, deposited on a ceramic honeycomb structure coated with aluminium oxide or cerium/zirconium oxide, the honeycomb structure having: a nickel content of 1,26 % by weight or more, but not more than 1,29 % by weight, 62 cells per cm2 or more, but not more than 140 cells per cm2 ,

a diameter of 100 mm or more, but not more than 120 mm, and a length of 60 mm or more, but not more than 150 mm, for use in the production of motor vehicles 0 %-31.12.20240.5508ex3815199010Catalysts consisting of chromium trioxide, dichromium trioxide or organometallic compounds of chromium, fixed on a silicon dioxide support with a pore volume of 2 cm3/g or more (as determined by the nitrogen absorption method)0 %-31.12.20260.2799ex3815199015Catalyst, in the form of a powder, consisting of a mixture of metal oxides fixed on a support of silicon dioxide, containing by weight 20 % or more but not more than 40 % of molybdenum, bismuth and iron evaluated together, for use in the manufacture of acrylonitrile0 %-31.12.2024 0.2798ex3815199020 Catalyst, in the form of solid spheres, of a diameter of 4 mm or more but not more than 12 mm, and consisting of a mixture of molybdenum oxide and other metal oxides, supported on silicon dioxide and/or aluminium oxide, for use in the manufacture of acrylic acid 0 %-31.12.20240.6049ex3815199025Catalyst in the form of spheres of a diameter of 4,2 mm or more but not more than 9 mm, consisting of a mixture of metal oxides containing predominantly oxides of molybdenum, nickel, cobalt and iron, on a support of aluminium oxide, for use in the manufacture of acrylic aldehyde0 %-31.12.20240.3435ex3815199030Catalyst containing titanium tetrachloride supported on magnesium dichloride, for use in the manufacture of polypropylene0 %-31.12.20240.7566ex3815199035Catalyst consisting of tungstosilicic acid hydrate (CAS RN 12027-43-9) impregnated on a support of silicon dioxide in the form of a powder0 %-31.12.20240.2792ex3815199065Catalyst consisting of phosphoric acid chemically bonded to a support of silicon dioxide0 %-31.12.20240.2791ex3815199070Catalyst consisting of organo-metallic compounds of aluminium and zirconium, fixed on a support of silicon dioxide0 %-31.12.20240.2790ex3815199075Catalyst consisting of organo-metallic compounds of aluminium and chromium, fixed on a support of silicon dioxide0 %-31.12.20240.2793ex3815199080Catalyst consisting of organo-metallic compounds of magnesium and titanium, fixed on a support of silicon dioxide, in the form of a suspension in mineral oil0 %-31.12.20240.2788ex3815199085Catalyst consisting of organo-metallic compounds of aluminium, magnesium and titanium, fixed on a support of silicon dioxide, in the form of powder0 %-31.12.20240.3899ex3815199086Catalyst containing titanium tetrachloride supported on magnesium dichloride, for use in the manufacture of polyolefins0 %-31.12.2024 0.4005ex3815909016Initiator based on dimethylaminopropyl urea0 %-31.12.20270.7528ex3815909025 Catalyst consisting by weight of: 30 % or more but not more than 33 % of bis(4-(diphenylsulphonio)phenyl)sulphide bis(hexafluorophosphate) (CAS RN 74227-35-3), and 24 % or more but not more than 27 % of diphenyl(4-phenylthio)phenylsuphonium hexafluorophosphate (CAS RN 68156-13-8) in propylene carbonate (CAS RN 108-32-7)

0 %-31.12.20240.5062ex3815909030 Catalyst, consisting of a suspension in mineral oil of: tetrahydrofuran complexes of magnesium chloride and titanium(III) chloride, and silicon dioxide, containing 6,6 % (± 0,6 %) by weight of magnesium, and containing 2,3 % (± 0,2 %) by weight of titanium 0 %-31.12.20250.7526ex3815909035 Catalyst containing by weight: 25 % or more but not more than 27,5 % of bis[4-(diphenylsuphonio)phenyl]sulphide bis(hexafluoroantimonate) (CAS RN 89452-37-9), and 20 % or more but not more than 22,5 % of diphenyl(4-phenylthio)phenylsufonium hexafluoroantimonate (CAS RN 71449-78-0) in propylene carbonate (CAS RN 108-32-7) 0 %-31.12.20240.7998ex3815909038 Photoinitiator, containing by weight: 80 % or more of polyethylene glycol di[β-4-[4-(2-dimethylamino-2-benzyl)butanoylphenyl]piperazine]propionate (CAS RN 886463-10-1), not more than 17 % of polyethylene glycol [β-4-[4-(2-dimethylamino-2-benzyl)butanoylphenyl]piperazine]propionate 0 %-31.12.20250.6006ex3815909040 Catalyst: containing molybdenum oxide and other metal oxides in a silicon dioxide matrix, in the form of hollow cylindrical solids of a length of 4 mm or more but not more than 12 mm for use in the manufacture of acrylic acid 0 %-31.12.2024 0.7243ex3815909043 Catalyst in powder form consisting by weight of 92,50 % (± 2) % titanium dioxide (CAS RN 13463-67-7), 5 % (± 1) % silicon dioxide (CAS RN 112926-00-8), and 2,5 % (± 1,5) % sulphur trioxide (CAS RN 7446-11-9) 0 %-31.12.20270.7999ex3815909048 Photoinitiator containing by weight: 88 % or more of α-(2-benzoylbenzoyl)-ω-[(2-benzoylbenzoyl)oxy]-poly(oxy-1,2-ethanediyl) (CAS RN 1246194-73-9), not more than 12 % of α-(2-benzoylbenzoyl)-ω-hydroxy-poly(oxy-1,2-ethanediyl) (CAS RN 1648797-60-7) 0 %-31.12.20250.3433ex3815909050Catalyst containing titanium trichloride, in the form of a suspension in hexane or heptane containing by weight, in the hexane- or heptane-free material, 9 % or more but not more than 30 % of titanium0 %-31.12.20240.2783ex3815909080Catalyst consisting predominantly of dinonylnaphthalenedisulphonic acid in the form of a solution in isobutanol0 %-31.12.20250.3430ex3815909081Catalyst, containing by weight 69 % or more but not more than 79 % of (2-hydroxy-1-methylethyl)trimethylammonium 2-ethylhexanoate0 %-31.12.20240.2782ex3815909085Catalyst based on aluminosilicate (zeolite), for the alkylation of aromatic hydrocarbons, for the transalkylation of alkylaromatic hydrocarbons or for the oligomerization of olefins0 %-31.12.20270.2909ex3815909086Catalyst, in the form of rodlets, consisting of an aluminosilicate (zeolite), containing by weight 2 % or more but not more than 3 % of rare-earth metal oxides and less than 1 % of disodium oxide0 %-31.12.20240.3732ex3815909088 Catalyst, consisting of titanium tetrachloride and magnesium chloride, containing by weight on an oil- and hexane-free basis: 4 % or more but not more than 10 % of titanium and 10 % or more but not more than 20 % magnesium 0 %-31.12.20240.3733ex3815909089Rhodococcus rhodocrous J1 bacteria, containing enzymes, suspended in a polyacrylamide gel or in water, for use as a catalyst in the production of acrylamide by the hydration of acrylonitrile0 %-31.12.2026

0.4408ex3817005010 Mixture of alkylbenzenes (C14-26) containing by weight: 35 % or more but not more than 60 % of eicosylbenzene, 25 % or more but not more than 50 % of docosylbenzene, 5 % or more but not more than 25 % of tetracosylbenzene 0 %-31.12.20240.3427ex3817008010 Mixture of alkylnaphthalenes, containing by weight: 88 % or more but not more than 98 % of hexadecylnaphthalene 2 % or more but not more than 12 % of dihexadecylnaphthalene 0 %-31.12.20240.4581ex3817008020Mixture of branched alkyl benzenes mainly containing dodecyl benzenes0 %-31.12.20240.5479ex3817008030Mixed alkylnaphthalenes, modified with aliphatic chains, of a chain-length varying from 12 to 56 carbon atoms0 %-31.12.20260.4006ex3819000020Fire resistant hydraulic fluid based on phosphate ester0 %-31.12.20240.7922ex382319102012-Hydroxyoctadecanoic acid (CAS RN 106-14-9) for use in the manufacture of polyglycerin-poly-12-hydroxyoctadecanoic acid esters0 %-31.12.20240.6038 ex38231930 ex38231930 20 30 Palm fatty acid distillate, whether or not hydrogenated, with free fatty acid content 80 % or more for use in the manufacture of: industrial monocarboxylic fatty acids of heading 3823, stearic acid of heading 3823, stearic acid of heading 2915, palmitic acid of heading 2915, or animal feed preparations of heading 2309 0 %-31.12.20240.6037 ex38231990 ex38231990 20 30 Palm acid oils from refining for use in the manufacture of: industrial monocarboxylic fatty acids of heading 3823, stearic acid of heading 3823, stearic acid of heading 2915, palmitic acid of heading 2915, or animal feed preparations of heading 2309 0 %-31.12.2024 0.2908ex3824991510Acid aluminosilicate (artificial zeolite of the Y type) in the sodium form, containing by weight not more than 11 % of sodium evaluated as sodium oxide, in the form of rodlets0 %-31.12.20240.8365ex3824999222 Solution containing: 30 % or more but not more than 40 % by weight of lithium hexafluorophosphate (CAS RN 21324-40-3), and 60 % or more but not more than 70 % by weight of ethyl methyl carbonate (CAS RN 623-53-0), or dimethyl carbonate (CAS RN 616-38-6) 3,2 %-31.12.20240.6810ex3824999223Butylphosphato complexes of titanium(IV) (CAS RN 109037-78-7), dissolved in ethanol and propan-2-ol0 %-31.12.20250.4909ex3824999229 Preparation containing by weight: 85 % or more but not more than 99 % of polyethylene glycol ether of butyl 2-cyano 3-(4-hydroxy-3-methoxyphenyl) acrylate, and 1 % or more but not more than 15 % of polyoxyethylene (20) sorbitan trioleate 0 %-31.12.20250.7618ex3824999231Liquid crystal mixtures for use in the manufacture of LCD (liquid crystal display) modules0 %-31.12.20240.4707ex3824999232Mixture of divinylbenzene-isomers and ethylvinylbenzene-isomers, containing by weight 56 % or more but not more than 85 % of divinylbenzene (CAS RN 1321-74-0)0 %-31.12.20240.3083 ex38249992 ex38249993 ex38249996 33 40 40 Anti-corrosion preparations consisting of salts of dinonylnaphthalenesulphonic acid, either: on a support of mineral wax, whether or not modified chemically, or

in the form of a solution in an organic solvent 0 %-31.12.20240.4153ex3824999235Preparations containing not less than 92 % or more but not more than 96,5 % by weight of 1,3:2,4-bis-O-(4-methylbenzylidene)-D-glucitol and also containing carboxylic acid derivatives and an alkyl sulphate0 %-31.12.2024 0.4523ex3824999237Mixture of acetates of 3-butene-1,2-diol with a content by weight of 65 % or more of 3-butene-1,2-diol diacetate (CAS RN 18085-02-4)0 %-31.12.20240.4152ex3824999239Preparation containing not less than 47 % by weight of 1,3:2,4-bis-O-benzylidene-D-glucitol0 %-31.12.20240.6779ex3824999240Solution of 2-chloro-5-(chloromethyl)-pyridine (CAS RN 70258-18-3) in organic diluent0 %-31.12.20250.6091ex3824999242Preparation of tetrahydro-α-(1-naphthylmethyl)furan-2-propionic acid (CAS RN 25379-26-4) in toluene0 %-31.12.20240.7724ex3824999243 Preparation containing by weight: 65 % or more, but not more than 95 % of isopropylated triaryl phosphate (CAS RN 68937-41-7) and 5 % or more, but not more than 35 % of triphenyl phosphate (CAS RN 115-86-6) 0 %-31.12.20240.3067ex3824999245Preparation consisting predominantly of γ-butyrolactone and quaternary ammonium salts, for the manufacture of electrolytic capacitors0 %-31.12.20240.4279ex3824999249Preparation based on 2,5,8,11-tetramethyl-6-dodecyn-5,8-diol ethoxylate (CAS RN 169117-72-0)0 %-31.12.20270.3065ex3824999251Mixture containing by weight 40 % or more but not more than 50 % of 2-hydroxyethyl methacrylate and 40 % or more but not more than 50 % of glycerol ester of boric acid0 %-31.12.20240.7742ex3824999252 Electrolyte containing: 5 % or more but not more than 20 % lithium hexafluorophosphate (CAS RN 21324-40-3) or lithium tetrafluoroborate (CAS RN 14283-07-9), 60 % or more but not more than 90 % of a mixture of ethylene carbonate (CAS RN 96-49-1), dimethyl carbonate (CAS RN 616-38-6) and/or ethyl methyl carbonate (CAS RN 623-53-0), 0,5 % or more but not more than 20 % 1,3,2-dioxathiolane 2,2-dioxide (CAS RN 1072-53-3), for use in the manufacture of motor vehicle batteries 3,2 %-31.12.2024 0.3061ex3824999253 Preparations consisting predominantly of ethylene glycol and: either diethylene glycol, dodecanedioic acid and ammonia water, or N,N-dimethylformamide, or γ-butyrolactone, or silicon oxide, or ammonium hydrogen azelate, or ammonium hydrogen azelate and silicon oxide, or dodecanedioic acid, ammonia water and silicon oxide, for the manufacture of electrolytic capacitors 0 %-31.12.20240.4434ex3824999254Poly(tetramethylene glycol) bis[(9-oxo-9H-thioxanthen-1-yloxy)acetate] with an average polymer chain length of less than 5 monomer units (CAS RN 813452-37-8)0 %-31.12.20260.6025ex3824999255 Additives for paints and coatings, containing: a mixture of esters of phosphoric acid obtained from the reaction of phosphoric anhydride with 4-(1,1-dimethylpropyl) phenol and copolymers of styrene-allyl alcohol (CAS RN 84605-27-6), and 30 % or more but not more than 35 % by weight of isobutyl alcohol 0 %-31.12.20280.4431ex3824999256Poly(tetramethylene glycol) bis[(2-benzoyl-phenoxy)acetate] with an average polymer chain length of less than 5 monomer units0 %-31.12.20240.4425ex3824999257Poly(ethylene glycol) bis(p-dimethyl)aminobenzoate with an average polymer chain length of less than 5 monomer units0 %-31.12.20240.6067ex3824999259Potassium tert-butanolate (CAS RN 865-47-4) in the form of a solution in tetrahydrofuran0 %-31.12.20240.5050ex38249992613’,4’,5’-Trifluorobiphenyl-2-amine, in the form of a solution in toluene containing by weight 80 % or more but not more than 90 % of 3’,4’,5’-trifluorobiphenyl-2-amine0 %-31.12.20250.7831ex3824999262Solution of 9-borabicyclo[3.3.1]nonane (CAS RN 280-64-8) in tetrahydrofurane (CAS RN 109-99-9), containing by weight 6 % or more 9-borabicyclo[3.3.1]nonane0 %-31.12.2024

0.3122ex3824999265Mixture of primary tert-alkylamines0 %-31.12.20240.6720ex3824999268 Preparation containing by weight: 20 % (±1 %) ((3-(sec-butyl)-4-(decyloxy)phenyl)methanetriyl) Tribenzene (CAS RN 1404190-37-9) Dissolved in: 10 % (± 5 %) 2-sec-Butylphenol (CAS RN 89-72-5) 64 %( ±7 %) Solvent naphtha (petroleum), heavy aromatic (CAS RN 64742-94-5) and 6 % (± 1.0 %) Naphthalene (CAS RN 91-20-3) 0 %-31.12.20250.6719ex3824999269 Preparation containing by weight: 80 % or more but not more than 92 % of Bisphenol-A bis(diphenyl phosphate) (CAS RN 5945-33-5) 7 % or more but not more than 20 % oligomers of Bisphenol-A bis(diphenyl phosphate) and not more than 1 % triphenyl phosphate (CAS RN 115-86-6) 0 %-31.12.20260.4409ex3824999270Mixture of 80 % (± 10 %) of 1-[2-(2-aminobutoxy)ethoxy]but-2-ylamine and 20 % (± 10 %) of 1-({[2-(2-aminobutoxy)ethoxy]methyl} propoxy)but-2-ylamine0 %-31.12.20240.6198ex3824999272N-(2-Phenylethyl)-1,3-benzenedimethanamine derivatives (CAS RN 404362-22-7)0 %-31.12.20240.8471ex3824999273Tri-C8-10-alkyl amines (CAS RN 68814-95-9) with a purity by weight of 95 % or more0 %-31.12.20270.8463ex3824999274 Reaction mass containing by weight: 22,4 % or more, but not more than 26,4 % of 3-methylphenyl diphenyl phosphate (CAS RN 69500-28-3); 17,3 % or more, but not more than 21,3 % of 4-methylphenyl diphenyl phosphate (CAS RN 78-31-9); 5 % or more, but not more than 9 % of bis(3-methylphenyl) phenyl phosphate (CAS RN 34909-68-7); 8,9 % or more, but not more than 12,9 % of 3-methylphenyl 4-methylphenyl phenyl phosphate (CAS RN 222165-66-4); 26,9 % or more, but not more than 30,9 % of triphenyl phosphate (CAS RN 115-86-6) 0 %-31.12.2027 0.8486ex3824999275 Mixture, containing by weight: not more than 75 % of tetrabutyltin (CAS RN 1461-25-2), not more than 20 % of tributyltin chloride (CAS RN 1461-22-9), not more than 4 % of dibutyltin dichloride (CAS RN 683-18-1), for use in the production of butyltin compounds used in glass manufacture and tributyltin chloride used as a catalyst in the pharmaceutical industry 3,2 %-31.12.20270.6114ex3824999276 Preparation containing: 74 % or more but not more than 90 % by weight of (S)-α-hydroxy-3-phenoxy-benzeneacetonitrile (CAS RN 61826-76-4) and 10 % or more but not more than 26 % by weight of toluene (CAS RN 108-88-3) 0 %-31.12.20240.8506ex3824999279 Mixture, containing by weight: tributyltin chloride (CAS RN 1461-22-9) with a purity by weight of 80 % or more, not more than 5 % tetrabutyltin (CAS RN 1461-25-2), not more than 6 % dibutyltin dichloride (CAS RN 683-18-1), not more than 11 % o-xylene (CAS RN 95-47-6), for use in the production of tributyltin chloride used as a catalyst in the pharmaceutical industry 3,2 %-31.12.20270.7462ex3824999281Reaction mass of 3- [(diphenoxyphosphoryl)oxy]phenyl triphenyl 1,3-phenylene bis(phosphate) and tetraphenyl 1,3-phenylene bis(phosphate)0 %-31.12.20280.6546ex3824999282T-butylchloride dimethylsilane (CAS RN 18162-48-6) solution in toluene0 %-31.12.20240.8517ex38249992831-(Cedr-8-en-9-yl)ethanone (CAS RN 32388-55-9) with a purity by weight of 70 % or more, but not more than 90 %0 %-31.12.20240.3074ex3824999284

Preparation consisting by weight of 83 % or more of 3a,4,7,7a-tetrahydro-4,7-methanoindene (dicyclopentadiene), a synthetic rubber, whether or not containing by weight 7 % or more of tricyclopentadiene, and: either an aluminium-alkyl compound, or an organic complex of tungsten or an organic complex of molybdenum 0 %-31.12.2024 0.8499ex3824999286Tall oil N,N-dimethyl fatty amides (CAS RN 68308-74-7) with a purity by weight of 99 % or more0 %-31.12.20270.3069ex38249992882,4,7,9-Tetramethyldec-5-yne-4,7-diol, hydroxyethylated (CAS RN 9014-85-1)0 %-31.12.20250.8083ex3824999292 Solution consisting of: 50 (± 2) % by weight sodium mentholate (CAS RN 19321-38-1), and 50 (± 2) % by weight light aliphatic solvent naphtha (petroleum) (CAS RN 64742-89-8) 0 %-31.12.20250.8121ex3824999293Solution of not more than 15 % by weight of lithium hexafluorophosphate (CAS RN 21324-40-3) in a mixture of ethylene carbonate (CAS RN 96-49-1), dimethyl carbonate (CAS RN 616-38-6) and ethyl methyl carbonate (CAS RN 623-53-0), contains organic carbonate derivatives as additives3,2 %-31.12.20240.8278ex3824999294({[2-(trifluoromethyl)phenyl]carbonyl}amino)methyl acetate (CAS RN 895525-72-1) with a content of at least 45 % by weight dissolved in N,N-dimethylacetamide (CAS RN 127-19-5)0 %-31.12.20260.8287ex3824999295Solution of methyl cis-1-{[(2,5-dimethylphenyl)acetyl]amino}-4-methoxycyclohexanecarboxylate (CAS RN 203313-47-7) in N,N-dimethylacetamide (CAS RN 127-19-5), containing by weight 25 % or more but not more than 45 % of the carboxylate0 %-31.12.20260.5961ex3824999330 Powder Mixture containing by weight: 85 % or more of zinc diacrylate (CAS RN 14643-87-9), not more than 5 % of 2,6-di-tert-butyl-alpha-dimethylamino-p-cresol (CAS RN 88-27-7), and not more than 10 % of zinc stearate (CAS RN 557-05-1) 0 %-31.12.20240.8498ex3824999333 Preparation containing by weight 60 % or more but not more than 70 % of calcium rel-(1R,2S)-cyclohexane-1,2-dicarboxylate (CAS RN 491589-22-1), 30 % or more but not more than 40 % of zinc stearate (CAS RN 557-05-1), 1 % or more but not more than 5 % of CI Pigment Blue 29 (CAS RN 57455-37-5) and 1 % or more but not more than 5 % of CI Pigment Violet 15 (CAS RN 12769-96-9) 0 %-31.12.2027 0.4719ex3824999335Paraffin with a level of chlorination of 70 % or more (CAS RN 63449-39-8)0 %-31.12.20240.8497ex3824999336Preparation containing by weight 60 % or more but not more than 70 % of calcium rel-(1R,2S)-cyclohexane-1,2-dicarboxylate (CAS RN 491589-22-1) and 30 % or more but not more than 40 % of zinc stearate (CAS RN 557-05-1)0 %-31.12.20270.4527ex3824999342Mixture of bis{4-(3-(3-phenoxycarbonylamino)tolyl)ureido}phenylsulphone, diphenyltoluene-2,4-dicarbamate and 1-[4-(4-aminobenzenesulphonyl)-phenyl]-3-(3-phenoxycarbonylamino-tolyl)-urea0 %-31.12.20240.7153ex3824999345 Sodium hydrogen 3-aminonaphthalene-1,5-disulphonate (CAS RN 4681-22-5) containing by weight: not more than 20 % of disodium sulphate, and not more than 10 % of sodium chloride 0 %-31.12.20260.7786ex3824999348

Nonhalogenated flame retardant containing by weight: 50 % or more, but not more than 65 % of piperazine pyrophosphate (CAS RN 66034-17-1), 35 % or more, but not more than 45 % of a phosphoric acid derivative and not more than 6 % of zinc oxide (CAS RN 1314-13-2) 0 %-31.12.20240.8062ex3824999351Tris(hydroxymethyl)phosphine oxide (CAS RN 1067-12-5) with a purity by weight of 85 % or more0 %-31.12.20250.6215ex3824999353Zinc dimethacrylate (CAS RN 13189-00-9), containing not more than 2,5 % by weight of 2,6-di-tert-butyl-alpha-dimethyl amino-p-cresol (CAS RN 88-27-7), in the form of powder0 %-31.12.20240.7497ex3824999360 Mixture of phytosterols containing by weight: 35 % or more but not more than 88 % sitosterols, 20 % or more but not more than 63 % campesterols, 14 % or more but not more than 38 % stigmasterols, not more than 13 % brassicasterols, not more than 10 % other stanols, and not more than 10 % other sterols 0 %-31.12.20240.2939ex3824999361Disodium 7,7’-(carbonyldiimino)bis(4-hydroxynaphthalene-2-sulphonate) (CAS RN 20324-87-2) with a purity by weight of 80 % or more0 %-31.12.2028 0.4290ex3824999363 Mixture of phytosterols, not in the form of powder, containing by weight: 75 % or more of sterols, not more than 25 % of stanols, for use in the manufacture of stanols/sterols or stanol/sterol esters 0 %-31.12.20270.7460ex3824999365Reaction mass of 1,1’-(isopropylidene)bis[3,5-dibromo-4-(2,3-dibromo-2-methylpropoxy)benzene] (CAS RN 97416-84-7) and 1,3-dibromo-2-(2,3-dibromo-2-methylpropoxy)-5-{2-[3,5-dibromo-4-(2,3,3-tribromo-2-methylpropoxy)phenyl]propan-2-yl}benzene0 %-31.12.20240.3117ex3824999370Oligomeric reaction product, consisting of bis(4-hydroxyphenyl) sulfone and 1,1’-oxybis(2-chloroethane)0 %-31.12.20240.8366ex3824999372Reaction product of octadecanoic acid methyl ester, with 1-(2-hydroxy-2-methylpropoxy)-2,2,6,6-tetramethyl-4-piperidinol (CAS RN 300711-92-6)0 %-31.12.20270.8371ex38249993741,3-Propanediamine, N1,N1’–1,2-ethanediylbis-, reaction products with cyclohexane and peroxidized N-butyl-2,2,6,6-tetramethyl-4-piperidinamine-2,4,6-trichloro-1,3,5-triazine reaction products (CAS RN 191680-81-6)0 %-31.12.20270.3112ex3824999375Mixture of phytosterols, in the form of flakes and balls, containing by weight 80 % or more of sterols and not more than 4 % of stanols0 %-31.12.20240.3049 ex38249993 ex38249996 85 57 Particles of silicon dioxide on which are covalently bonded organic compounds, for use in the manufacture of high performance liquid chromatography columns (HPLC) and sample preparation cartridges0 %-31.12.20240.4336ex3824999388 Mixture of phytosterols containing by weight: 60 % or more, but not more than 80 % of sitosterols, less than 15 % of campesterols, less than 5 % of stigmasterols, and less than 15 % of betasitostanols 0 %-31.12.2027 0.7420ex3824999630 Rare-earth concentrate containing by weight: 20 % or more but not more than 30 % of cerium oxide (CAS RN 1306-38-3), 2 % or more but not more than 10 % of lanthanum oxide (CAS RN 1312-81-8),

10 % or more but not more than 15 % of yttrium oxide (CAS RN 1314-36-9), and not more than 65 % of zirconium oxide (CAS RN 1314-23-4) including natural occurring hafnium oxide 0 %-31.12.20240.3078ex3824999635Calcined bauxite (refractory grade)0 %-31.12.20240.4542ex3824999637Structured silica alumina phosphate0 %-31.12.20240.8514ex38249996432-(Ethylthio)ethanethiol functionalized silicagel with a purity by weight of 98 % or more0 %-31.12.20270.7313ex3824999645 Lithium nickel cobalt aluminium oxide powder (CAS RN 177997-13-6) with: a particle size of less than 10 µm, a purity by weight of more than 98 % 3,2 %-31.12.20240.6628ex3824999646 Manganese zinc ferrite granulate, containing by weight: 52 % or more but not more than 76 % of iron(III)oxide, 13 % or more but not more than 42 % of manganese oxide, and 2 % or more but not more than 22 % of zinc oxide 0 %-31.12.20250.3064ex3824999647 Mixed metals oxides, in the form of powder, containing by weight: either 5 % or more of barium, neodymium or magnesium and 15 % or more of titanium, or 30 % or more of lead and 5 % or more of niobium, for use in the manufacture of dielectric films or for use as dielectric materials in the manufacture of multilayer ceramic capacitors 0 %-31.12.20240.6749ex3824999648Zirconium oxide (ZrO2), calcium oxide stabilised (CAS RN 68937-53-1) with a zirconium oxide content by weight of 92 % or more but not more than 97 %0 %-31.12.2025 0.5607ex3824999650Nickel hydroxide, doped with 12 % or more but not more than 18 % by weight of zinc hydroxide and cobalt hydroxide, of a kind used to produce positive electrodes for accumulators0 %-31.12.20270.6145ex3824999655 Carrier in powder form, consisting of: ferrite (Iron oxide) (CAS RN 1309-37-1) manganese oxide (CAS RN 1344-43-0) magnesium oxide (CAS RN 1309-48-4) styrene acrylate copolymer to be mixed with the toner powder, in the manufacturing of ink/toner filled bottles or cartridges for facsimile machines, computer printers and copiers 0 %-31.12.20240.5141ex3824999660Fused magnesia containing by weight 15 % or more of dichromium trioxide0 %-31.12.20260.8587ex3824999662 Viscous preparation essentially containing: by weight more than 5 % but not more than 15 % of poly(vinyl alcohol) (CAS RN 9002-89-5), by weight more than 10 % but not more than 20 % of 1-methoxy-2-propanol (CAS RN 107-98-2), water, for use as a protective coating for wafers during the slicing process in the manufacture of semiconductors 0 %-31.12.20280.3050ex3824999665 Aluminium sodium silicate, in the form of spheres of a diameter of: either 1,6mm or more but not more than 3,4 mm, or 4mm or more but not more than 6 mm 0 %-31.12.20240.8122ex3824999668 Lithium nickel dioxide (CAS RN 12325-84-7) containing by weight: less than 5 % of lithium hydroxide (CAS RN 1310-65-2), less than 5 % of lithium carbonate (CAS RN 554-13-2), and less than 15 % of nickel oxide (CAS RN 11099-02-8) 3,2 %-31.12.20240.3119ex3824999673 Reaction product, containing by weight: 1 % or more but not more than 40 % of molybdenum oxide,

10 % or more but not more than 50 % of nickel oxide, 30 % or more but not more than 70 % of tungsten oxide 0 %-31.12.2024 0.7010ex3824999674 Mixture with a non-stoichiometric composition: with a crystalline structure, with a content of fused magnesia-alumina spinel and with admixtures of silicate phases and aluminates, at least 75 % by weight of which consists of fractions with a grain size of 1-3 mm and at most 25 % consists of fractions with a grain size of 0-1 mm 0 %-31.12.20260.7147ex3824999680 Mixture consisting of: 64 % or more, but not more than 74 % by weight of amorphous silica (CAS RN 7631-86-9) 25 % or more, but not more than 35 % by weight of butanone (CAS RN 78-93-3) and not more than 1 % by weight of 3-(2,3-epoxypropoxy)propyltrimethoxysilane (CAS RN 2530-83-8) 0 %-31.12.20260.7553ex3824999683Cubic Boron nitride (CAS RN 10043-11-5) coated with nickel and/or nickelphosphide (CAS RN 12035-64-2)0 %-31.12.20240.5820ex3824999687 Platinum oxide (CAS RN 12035-82-4) fixed on a porous support of aluminium oxide (CAS RN 1344-28-1), containing by weight: 0,1 % or more but not more than 1 % of platinum, and 0,5 % or more but not more than 5 % of ethylaluminium dichloride (CAS RN 563-43-9) 0 %-31.12.20270.5939 ex38260010 ex38260010 20 29 Mixture of fatty acid methyl esters containing by weight at least: 65 % or more but not more than 75 % of C12 FAME, 21 % or more but not more than 28 % of C14 FAME, 4 % or more but not more than 8 % of C16 FAME, for use in the manufacture of detergents and home and personal care products 0 %-31.12.20240.5941 ex38260010 ex38260010 50 59 Mixture of fatty acid methyl esters containing by weight at least: 50 % or more but not more than 58 % of C8-FAME 35 % or more but not more than 50 % of C10-FAME for the manufacturing of high purity C8 or C10 fatty acid or fatty acid mixtures thereof or of high purity methylester of C8 or C10 fatty acid 0 %-31.12.2024 0.7756ex3827680005 Mixture of halogenated derivatives containing by weight: 30 % or more but not more than 60 % of difluoromethane (CAS RN 75-10-5), 30 % or more but not more than 60 % of trifluoroiodomethane (CAS RN 2314-97-8), 10 % or more but not more than 30 % of pentafluoroethane (CAS RN 354-33-6) 0 %-31.12.20240.6132 ex39011010 ex39014000 20 10 High flow linear low density polyethylene-1-butene / LLDPE (CAS RN 25087-34-7) in form of powder, with a melt flow rate (MFR 190 °C/2,16 kg) of 16g/10min or more, but not more than 24 g/10 min and a density (ASTM D 1505) of 0,922 g/cm3 or more, but not more than 0,926 g/cm3 and a vicat softening temperature of min. 94 °C 0 %m331.12.20240.8378 ex39011010 ex39014000 50 50 Copolymer of ethylene and 1-butene (CAS RN 25087-34-7) with: a density (ASTM D 1505) of 0,924 g/cm3 or more but not more than 0,928 g/cm3, a melt flow rate (190 °C/2,16 kg) of 48 g/10 min or more but not more than 52 g/10 min, and a peak melting temperature of 120 °C or more but not more than 124 °C 0 %-31.12.20270.8379 ex39011010 ex39014000 60 60 Copolymer of ethylene and 1-butene (CAS RN 25087-34-7) with:

a density (ASTM D 1505) of 0,922 g/cm3 or more but not more than 0,926 g/cm3 and a melt flow rate (190 °C/2,16 kg) of 18 g/10 min or more but not more than 22 g/10 min 0 %-31.12.20240.5142ex3901109030Polyethylene granules, containing by weight 10 % or more but not more than 25 % of copper0 %-31.12.20260.6897ex3901400030 Octene linear low-density polyethylene (LLDPE) produced by a Ziegler-Natta catalyst method in the form of pellets with: more than 10 % but not more than 20 % by weight of copolymer, a melt flow rate (MFR 190 °C/2,16 kg) of 0,7 g/10 min or more but not more than 0,9 g/10 min, and a density (ASTM D4703) of 0,911 g/cm3 or more, but not more than 0,913 g/cm3, for use in the co-extrusion processing of films for flexible food packaging 0 %m331.12.2025 0.6920ex3901908053 Copolymer of ethylene and acrylic acid (CAS RN 9010-77-9) with: an acrylic acid content of 18,5 % or more, but not more than 49,5 % by weight (ASTM D4094), and a melt flow rate of 10g/10 min or more (125°C/2,16 kg, ASTM D1238) 0 %m331.12.20250.6734ex3901908055 Zinc or sodium salt of an ethylene and acrylic acid copolymer, with: an acrylic acid content of 6 % or more but not more than 50 % by weight, and a melt flow rate of 1g/10 min or more at 190 °C/2,16 kg (measured using ASTM D1238) 0 %-31.12.20250.5049ex3901908067Copolymer made exclusively from ethylene and methacrylic acid monomers in which the methacrylic acid content is 11 % by weight or more0 %-31.12.20250.6998ex3901908073 Mixture containing by weight 80 % or more, but not more than 94 % of chlorinated polyethylene (CAS RN 64754-90-1) and 6 % or more, but not more than 20 % of styrene-acrylic copolymer (CAS RN 27136-15-8) 0 %-31.12.20260.2902ex3901908091Ionomer resin consisting of a salt of a copolymer of ethylene with methacrylic acid0 %-31.12.20240.3906ex3901908092Chlorosulphonated polyethylene0 %-31.12.20240.2899ex3901908093Copolymer of ethylene, vinyl acetate and carbon monoxide, for use as a plasticiser in the manufacture of roof sheets0 %-31.12.20240.3186ex3901908094Mixtures of A-B block copolymer of polystyrene and ethylene-butylene copolymer and A-B-A block copolymer of polystyrene, ethylene-butylene copolymer and polystyrene, containing by weight not more than 35 % of styrene0 %-31.12.20240.2898ex3901908097Chlorinated polyethylene, in the form of powder0 %-31.12.2024 0.2895ex3902100020 Polypropylene, containing no plasticiser, of a melting point of more than 150 °C (as determined by the ASTM D 3417 method), of a heat of fusion of 15 J/g or more but not more than 70 J/g, of an elongation at break of 1000 % or more (as determined by the ASTM D 638 method), of a tensile modulus of 69 MPa or more but not more than 379 MPa (as determined by the ASTM D 638 method) 0 %-31.12.20240.4591ex3902100040 Polypropylene, containing no plasticiser: of a tensile strength: of 32-77 MPa (as determined by the ASTM D638 method); of a flexural strength of 50-105 MPa (as determined by the ASTM D790 method); of a Melt Flow Rate (MFR) at 230 °C/ 2,16 kg of 5-15 g/10 min (as determined by the ASTM D1238 method);

with 40 % or more but not more than 80 % by weight of polypropylene, with 10 % or more but not more than 30 % by weight of glass fibre, with 10 % or more but not more than 30 % by weight of mica 0 %-31.12.20240.3180ex3902200010Polyisobutylene, of a number average molecular weight (Mn) of 700 or more but not more than 8000 %-31.12.20240.3179ex3902200020Hydrogenated polyisobutene, in liquid form0 %-31.12.20240.8125ex3902300020Hydrogenated block copolymer of styrene and isoprene (CAS RN 68648-89-5), containing by weight less than 37 % of styrene0 %-31.12.20250.8232ex3902300030Hydrogenated copolymer of styrene, isoprene and butadiene, containing by weight 28 % or more, but not more than 55 % of propylene0 %-31.12.20260.3181ex3902300091A-B Block copolymer of polystyrene and an ethylene-propylene copolymer, containing by weight 40 % or less of styrene, in one of the forms mentioned in note 6 (b) to Chapter 390 %-31.12.2024 0.5143ex3902300095 A-B-A block copolymer, consisting of: a copolymer of propylene and ethylene and 21 % (± 3 %) by weight of polystyrene 0 %-31.12.20260.5138ex3902300097 Liquid ethylene-propylene-copolymer with: a flashpoint of 250 °C or more, a viscosity index of 150 or more, of a number average molecular weight (Mn) of 650 or more 0 %-31.12.20260.4424ex3902909052Amorphous poly-alpha-olefin copolymer blend of poly(propylene-co-1-butene) and petroleum hydrocarbon resin0 %-31.12.20240.4509ex3902909055Thermoplastic elastomer, with an A-B-A block copolymer structure of polystyrene, polyisobutylene and polystyrene containing by weight 10 % or more but not more than 35 % of polystyrene0 %-31.12.20240.4768ex3902909060 Non-hydrogenated 100 % aliphatic resin (polymer), with the following characteristics: liquid at room temperature obtained by cationic polymerisation of C-5 alkenes monomers with a number average molecular weight (Mn) of 370 (± 50) with a weight average molecular weight (Mw) of 500 (± 100) 0 %-31.12.20240.7950ex3902909065Brominated butadiene-styrene copolymer (CAS RN 1195978-93-8) with a bromine content of 60 % by weight or more but not more than 68 %, in forms as defined in Note 6 (b) to Chapter 390 %-31.12.20250.4040ex3902909070 Synthetic poly-alpha-olefin with a viscosity of 3 or more but not more than 9 centistokes (measured at 100 ° Celsius according to the ASTM D 445 method), obtained by polymerization of dodecene with or without: not more than 40 % by weight of tetradecene and/or not more than 2 % by weight decene and/or not more than 2 % by weight of hexadecene 0 %-31.12.20260.6422 ex39029090 ex39119099 75 28 Polycarboxylate sodium salt of 2,5-furandione and 2,4,4-trimethylpentene in powder form0 %-31.12.2024 0.2900ex3902909092Polymers of 4-methylpent-1-ene0 %-31.12.20240.6214ex3902909094Chlorinated polyolefins, whether or not in a solution or dispersion0 %-31.12.20240.4166ex3903190040 Crystalline polystyrene with: a melting point of 268 °C or more but not more than 272 °C a setting point of 232 °C or more but not more than 247 °C,

whether or not containing additives and filling material 0 %-31.12.20260.5175ex3903909015 Copolymer in the form of granules containing by weight: 78 (± 4 %) of styrene, 9 (± 2 %) of n-butyl acrylate, 11 (± 3 %) of n-butyl methacrylate,, 1.5 (± 0,7 %) of methacrylic acid and 0,01 % or more but not more than 2,5 % of polyolefinic wax 0 %-31.12.20240.5176ex3903909020 Copolymer in the form of granules containing by weight: 83 ± 3 % styrene, 7 ± 2 % n-butyl acrylate, 9 ± 2 % n-butyl methacrylate and 0,01 % or more but not more than 1 % of polyolefinic wax 0 %-31.12.20260.7861ex3903909033Copolymer of styrene, divinylbenzene and chloromethylstyrene (CAS RN 55844-94-5) with a purity by weight of 99 % or more0 %-31.12.20240.2891 ex39039090 ex39119099 35 43 Copolymer of α-methylstyrene and styrene, having a softening point of more than 113 oC0 %-31.12.20240.7417 ex39039090 ex39046980 38 88 Polytetrafluoroethylene (CAS RN 9002-84-0) encapsulated with an acrylonitrile-styrene copolymer (CAS RN 9003-54-7), with a content by weight of each polymer of 50 % (± 1 %)0 %-31.12.2027 0.8415ex3903909043 Mixture of polymers consisting by weight of: 10 % or more but not more than 30 % of a styrene-ethylene-butylene-styrene block copolymer (CAS RN 66070-58-4), 25 % or more but not more than 45 % of mineral oil (CAS RN 8042-47-5), 25 % or more but not more than 45 % of calcium carbonate (CAS RN 1317-65-3), 10 % or more but not more than 20 % of polypropylene (CAS RN 9003-07-0), and 1 % or more but not more than 3 % of a copolymer of α-methylstyrene and vinyltoluene (CAS RN 9017-27-0) 0 %-31.12.20270.6565ex3903909045 Preparation, in form of powder, containing by weight: 86 % or more but not more than 90 % of styrene-acrylic-copolymer and 9 % or more but not more than 11 % of fatty acid ethoxylate (CAS RN 9004-81-3) 0 %m331.12.20240.5473 ex39039090 ex39119099 60 60 Copolymer of styrene with maleic anhydride, either partially esterified or completely chemically modified, of an average molecular weight (Mn) of not more than 4500, in flake or powder form0 %-31.12.20260.6736ex3903909065Copolymer of styrene with 2, 5-furandione and (1-methylethyl)benzene in the form of flakes or powder (CAS RN 26762-29-8)0 %-31.12.20250.6804ex3903909070 Copolymer in the form of granules containing by weight: 75 % (± 7 %) styrene and 25 % (± 7 %) methylmethacrylate 0 %m331.12.20250.3910ex3903909080 Granules of copolymer of styrene and divinylbenzene of a minimum diameter of 150 µm and a maximum diameter of 800 µm and containing by weight: minimum 65 % styrene, maximum 25 % divinylbenzene for use in the manufacture of ion exchange resins 0 %-31.12.2024 0.4410ex3903909086 Mixture containing by weight: 45 % or more but not more than 65 % of polymers of styrene, 30 % or more but not more than 45 % of poly(phenylene ether), and not more than 11 % of additives 0 %-31.12.20240.2887 ex39043000 ex39044000 30 91 Copolymer of vinyl chloride with vinyl acetate and vinyl alcohol, containing by weight: 87 % or more but not more than 92 % of vinyl chloride,

2 % or more but not more than 9 % of vinyl acetate and 1 % or more but not more than 8 % of vinyl alcohol, in one of the forms mentioned in note 6 (a) or (b) to Chapter 39, for the manufacture of goods of headings 3215 or 8523 or for use in the manufacture of coatings for containers and closures of a kind used for preserving food and drink 0 %-31.12.20240.2885ex3904610020Copolymer of tetrafluoroethylene and trifluoro(heptafluoropropoxy)ethylene, containing 3,2 % or more but not more than 4,6 % by weight of trifluoro(heptafluoropropoxy)ethylene and less than 1 mg/kg of extractable fluoride ions0 %-31.12.20240.7675ex3904698020Copolymer of tetrafluoroethylene, heptafluoro-1-pentene and ethene (CAS RN 94228-79-2)0 %-31.12.20240.7626ex3904698030Copolymer of tetrafluoroethylene, hexafluoropropene and ethene0 %-31.12.20240.4981ex3904698081Poly(vinylidene fluoride) (CAS RN 24937-79-9)0 %-31.12.20250.5560ex3904698085Copolymer of ethylene and chlorotrifluoroethylene, whether or not modified with hexafluoroisobutylene, whether or not containing fillers0 %-31.12.20270.3285ex3904698094Copolymer of ethylene and tetrafluoroethylene0 %-31.12.20240.2883ex3904698096Polychlorotrifluoroethylene, in one of the forms mentioned in note 6 (a) and (b) to Chapter 390 %-31.12.20240.3745ex3904698097Copolymer of chlorotrifluoroethylene and vinylidene difluoride0 %-31.12.2024 0.8414ex3905910035Aqueous solution of a copolymer of vinylpyrrolidone and N,N-dimethylaminopropyl methacrylamide sulfate (CAS RN 175893-71-7), containing by weight 8 % or more, but not more than 12 % of copolymer0 %-31.12.20270.5774ex3905910040Water soluble copolymer of ethylene and vinyl alcohol (CAS RN 26221-27-2), containing by weight not more than 38 % of the monomer unit ethylene0 %-31.12.20270.8126ex3905910050 Aqueous solution consisting by weight of: 10 % or more but not more than 20 % of a copolymer of vinyl pyrrolidone, N,N-dimethylaminopropyl methacrylamide and 3 (methacryloylamino)propyllauryldimethylammonium chloride (CAS RN 306769-73-3), not more than 1 % preservatives 0 %-31.12.20250.8145ex3905910060 Copolymer of vinylpyrrolidone, vinyl caprolactam and dimethylaminoethyl methacrylate (CAS RN 102972-64-5) in solid form, or as an aqueous solution containing by weight: 27 % or more but not more than 33 % of copolymer, not more than 1,5 % of ethanol (CAS RN 64-17-5), not more than 1 % of preservatives 0 %-31.12.20250.8138ex3905910070 Aqueous solution, containing by weight: 25 % or more but not more than 35 % of a copolymer of vinyl caprolactam, vinyl pyrrolidone, N,N-dimethylaminopropyl methacrylamide and 3-(methacryloylamino)propyllauryldimethylammonium chloride (CAS RN 748809-45-2), 10 % or more but not more than 16 % of ethanol (CAS RN 64-17-5) whether or not denatured with tert-butyl alcohol (CAS RN 75-65-0) and/or denatonium benzoate (CAS RN 3734-33-6) 0 %-31.12.20250.8139ex3905910080Copolymer of vinylpyrrolidone, acrylic acid and dodecyl methacrylate (CAS RN 83120-95-0)0 %-31.12.20250.3283ex3905999095Hexadecylated or eicosylated polyvinylpyrrolidone0 %-31.12.2024

0.2880ex3905999096 Polymer of vinyl formal, in one of the forms mentioned in note 6 (b) to Chapter 39, of a weight average molecular weight (Mw) of 25000 or more but not more than 150000 and containing by weight: 9,5 % or more but not more than 13 % of acetyl groups evaluated as vinyl acetate and 5 % or more but not more than 6,5 % of hydroxy groups evaluated as vinyl alcohol 0 %-31.12.20240.3282ex3905999097Povidone (INN)-iodine (CAS RN 25655-41-8)0 %-31.12.20240.3278ex3905999098Poly(vinyl pyrrolidone) partially substituted by triacontyl groups, containing by weight 78 % or more but not more than 82 % of triacontyl groups0 %-31.12.20240.327639069060Copolymer of methyl acrylate with ethylene and a monomer containing a non-terminal carboxy group as a substituent, containing by weight 50 % or more of methyl acrylate, whether or not mixed with silicon dioxide0 %-31.12.20240.3279ex3906909010Polymerization product of acrylic acid with small quantities of a polyunsaturated monomer, for the manufacture of medicaments of heading 3003 or 30040 %-31.12.20240.7347ex3906909023Copolymer of methylmethacrylate, butylacrylate, glycidylmethacrylate and styrene (CAS RN 37953-21-2), with an epoxy equivalent weight of not more than 500, in form of ground flakes with a particle size of not more than 1 cm0 %-31.12.20270.6672ex3906909033Core shell copolymer of butyl acrylate and alkyl methacrylate, with a particle size of 5 µm or more but not more than 10 µm0 %-31.12.20250.6663ex3906909037Copolymer of trimethylolpropane trimethacrylate and methyl methacrylate (CAS RN 28931-67-1), in microsphere form with an average diameter of 3 µm0 %-31.12.20250.4667ex3906909041Poly(alkyl acrylate) with an ester alkyl chain of C10 to C300 %-31.12.20240.7125ex3906909043Copolymer of methacrylic esters, butylacrylate and cyclic dimethylsiloxanes (CAS RN 143106-82-5)0 %-31.12.2026 0.2886ex3906909050 Polymers of esters of acrylic acid with one or more of the following monomers in the chain: chloromethyl vinyl ether, chloroethyl vinyl ether, chloromethylstyrene, vinyl chloroacetate, methacrylic acid, butenedioic acid monobutyl ester, butenedioic acid monocyclohexyl ester, containing by weight not more than 5 % of each monomer unit 0 %-31.12.20240.8579ex3906909058 Mixture of polymers, containing by weight: 77 % or more but not more than 81 % of polyacrylamide (CAS RN 9003-05-8), 18 % or more but not more than 21 % of polyethylene glycol (CAS RN 25322-68-3) 0 %-31.12.20280.7499ex3906909060 Aqueous dispersion containing by weight: more than 10 % but not more than 15 % of ethanol, and more than 7 % but not more than 11 % of a reaction product of poly(epoxyalkylmethacrylate-co-divinylbenzene) with a glycerol derivative 0 %-31.12.20240.6425ex3906909073 Preparation containing by weight: 33 % or more but not more than 37 % of butyl methacrylate - methacrylic acid copolymer, 24 % or more but not more than 28 % of propylene glycol, and 37 % or more but not more than 41 % of water 0 %-31.12.20240.6891ex3907100020Polyoxymethylene with acetyl endcaps, containing polydimethylsiloxane and fibers of a copolymer of terephthalic acid and 1,4-phenyldiamine0 %-31.12.20240.3272ex3907291110Poly(ethylene oxide) of a number average molecular weight (Mn) of 100000 or more0 %-31.12.20240.4378ex3907291120Bis[Methoxypoly[ethyleneglycol)]-maleimidopropionamide, chemically modified with lysine, of a number average molecular weight (Mn) of 400000 %-31.12.2024

0.7099ex3907292025 Copolymer of propylene oxide and butylene oxide, monododecylether, containing by weight: 48 % or more but not more than 52 % of propylene oxide and 48 % or more but not more than 52 % of butylene oxide 0 %-31.12.20240.2876ex3907292030Mixture, containing by weight 70 % or more but not more than 80 % of a polymer of glycerol and 1,2-epoxypropane and 20 % or more but not more than 30 % of a copolymer of dibutyl maleate and N-vinyl-2-pyrrolidone0 %-31.12.20240.7532ex3907292035 Mixture containing by weight: 5 % or more but not more than 15 % of a copolymer of glycerol, propylene oxide and ethylene oxide (CAS RN 9082-00-2), and 85 % or more but not more than 95 % of a copolymer of sucrose, propylene oxide and ethylene oxide (CAS RN 26301-10-0) 0 %-31.12.20240.4013ex3907292040Copolymer of tetrahydrofuran and tetrahydro-3-methylfuran (CAS RN 38640-26-5) with a number average molecular weight (Mn) of 900 or more but not more than 36000 %-31.12.20280.6351ex3907292050 Poly(p-phenylene oxide) in the form of powder with: a glass-transition temperature of 210 °C or more, a weight average molecular weight (Mw) of 35000 or more but not more than 80000, an inherent viscosity of 0,2 or more but not more than 0,6 dl/gram 0 %-31.12.20240.3271ex3907299915Poly(oxypropylene) having alkoxysilyl end-groups0 %-31.12.20240.7478ex39072999202,3-Bis(methylpolyoxyethylene-oxy)-1-[(3-maleimido-1-oxopropyl)amino]propyloxy propane (CAS RN 697278-30-1) with a number average molecular weight (Mn) of at least 20 kDa whether or not modified with a chemical entity enabling a linkage between the PEG and a protein or a peptide0 %-31.12.20240.2920ex3907299930Homopolymer of 1-chloro-2,3-epoxypropane (epichlorohydrin)0 %-31.12.2024 0.7484ex3907299940N-(methoxypoly (ethylene glycol) -N-(1-acetyl- (2-methoxypoly (ethylene glycol)) -glycine (CAS RN 600169-00-4) with a number average molecular weight (Mn) for polyethylene glycol of 40 kDa0 %-31.12.20240.3269ex3907299945Copolymer of ethylene oxide and propylene oxide, having aminopropyl and methoxy end-groups0 %-31.12.20240.4536ex3907299950Vinyl-silyl terminated perfluoropolyether polymer or an assortment of two components consisting of the same type of vinyl-silyl terminated perfluoropolyether polymer as the main ingredient0 %-31.12.20240.4546ex3907299955Succinimidyl ester of methoxy poly(ethylene glycol)propionic acid, of a number average molecular weight (Mn) of 50000 %-31.12.20240.5144ex3907299960Polytetramethylene oxide di-p-aminobenzoate0 %-31.12.20260.8491ex3907299970Poly(oxy-1,4-phenyleneoxy-1,4-phenylenecarbonyl-1,4-phenylene) (CAS RN 29658-26-2) containing by weight not more than 35 % of additives0 %-31.12.20270.6839ex3907300015 Epoxide resin, halogen-free, containing by weight more than 2 % phosphoros calculated on the solid content, chemically bound in the epoxide resin, not containing any hydrolysable chloride or containing less than 300 ppm hydrolysable chloride, and containing solvents, for use in the manufacture of prepreg sheets or rolls of a kind used for the production of printed circuits

0 %-31.12.20250.6840ex3907300025 Epoxide resin containing by weight 21 % or more of brome, not containing any hydrolysable chloride or containing less than 500 ppm hydrolysable chloride, and containing solvents 0 %-31.12.20250.2759ex3907300040Epoxide resin, containing by weight 70 % or more of silicon dioxide, for the encapsulation of goods of headings 8504, 8533, 8535, 8536, 8541, 8542 or 85480 %-31.12.2024 0.7427ex3907300070 Preparation of epoxy resin (CAS RN 29690-82-2) and phenolic resin (CAS RN 9003-35-4) containing by weight: 65 % or more but not more than 75 % of silicon dioxide (CAS RN 60676-86-0), and none or not more than 0,5 % of carbon black (CAS RN 1333-86-4) 0 %-31.12.20270.2541ex3907400035α-Phenoxycarbonyl-ω-phenoxypoly[oxy(2,6-dibromo-1,4-phenylene) isopropylidene(3,5-dibromo-1,4-phenylene)oxycarbonyl] (CAS RN 94334-64-2)0 %-31.12.20240.2564ex3907400045α-(2,4,6-Tribromophenyl)-ω-(2,4,6-tribromophenoxy)poly[oxy(2,6-dibromo-1,4-phenylene)isopropylidene(3,5-dibromo-1,4-phenylene)oxycarbonyl] (CAS RN 71342-77-3)0 %-31.12.20240.6352ex3907400070 Polycarbonate of phosgene and bisphenol A: containing by weight 12 % or more but not more than 26 % of a copolymer of isophthaloyl chloride, terephthaloyl chloride and resorcinol, with p-cumylphenol endcaps, and with a weight average molecular weight (Mw) of 29900 or more but not more than 31900 0 %-31.12.20240.6355ex3907400080Polycarbonate of carbonic dichloride, 4,4’-(1-methylethylidene)bis[2,6-dibromophenol] and 4,4’-(1-methylethylidene)bis[phenol] with 4-(1-methyl-1-phenylethyl)phenol endcaps0 %-31.12.20240.3263ex3907690010Copolymer of terephthalic acid and isophthalic acid with ethylene glycol, butane–1,4-diol and hexane–1,6-diol0 %-31.12.20240.298039077000Poly(lactic acid)0 %-31.12.20240.2918ex3907919010Diallyl phthalate prepolymer, in powder form0 %-31.12.20240.2977ex3907998010Poly(oxy-1,4-phenylenecarbonyl) (CAS RN 26099-71-8), in the form of powder0 %-31.12.20240.5639ex3907998025Copolymer, containing 72 % by weight or more of terephthalic acid and/or isomers thereof and cyclohexanedimethanol0 %-31.12.20270.4940 ex39079980 ex39139000 30 20 Poly(hydroxyalkanoate), predominantly consisting of poly(3-hydroxybutyrate)0 %-31.12.2025 0.7491ex3907998035 Copolymer in form of a clear, pale yellow liquid, consisting of phthalic acid isomers and/or aliphatic dicarboxylic acids, aliphatic diols, and fatty acid end-caps with: a hydroxyl number of 120 mg KOH or more but not more than 350 mg KOH, a viscosity at 25 °C of 2000 cPs or more but not more than 8000 cPs, and an acid value less than 10 mg KOH/g 0 %-31.12.20240.5057ex3907998080Copolymer, consisting of 72 % by weight or more of terephthalic acid and/ or derivatives thereof and cyclohexanedimethanol, completed with linear and/ or cyclic dioles0 %-31.12.20250.2923ex3908900010Poly(iminomethylene-1,3-phenylenemethyleneiminoadipoyl), in one of the forms mentioned in note 6 (b) to Chapter 390 %-31.12.20240.3261ex3908900030Reaction product of mixtures of octadecanecarboxylic acids polymerised with an aliphatic polyetherdiamine0 %-31.12.20240.7428ex3909200010

Polymer mixture, containing by weight: 60 % or more but not more than 75 % of melamine resin (CAS RN 9003-08-1), 15 % or more but not more than 25 % of silicon dioxide (CAS RN 14808-60-7 or 60676-86-0), 5 % or more but not more than 15 % of cellulose (CAS RN 9004-34-6), and 1 % or more but not more than 15 % of phenolic resin (CAS RN 25917-04-8) 0 %-31.12.20270.5032ex3909400020Powder of thermosetting resin in which magnetic particles have been evenly distributed, for use in the manufacture of ink for photocopiers, fax machines, printers and multifunction devices0 %-31.12.20250.7865ex3909400070Polymer in the form of flakes composed of 98 % or more by weight of phenolic resin (brominated octylphenol-formaldehyde) with a softening point of 80°C or more but not exceeding 95°C according to standard ASTM E28-92 (CAS RN 112484-41-0)0 %-31.12.2024 0.4595ex3909509010 UV curable water soluble liquid photopolymer consisting of a mixture by weight of 60 % or more of two-functional acrylated polyurethane oligomers and 30 % (± 8 %) of mono-functional and tri-functional (metha) acrylates, and 10 % (± 3 %) of hydroxyl functionalized mono-functional (metha) acrylates 0 %-31.12.20240.6423ex3909509020 Preparation containing by weight: 14 % or more but not more than 18 % of ethoxylated polyurethane modified with hydrophobic groups, 3 % or more but not more than 5 % of enzymatically modified starch, and 77 % or more but not more than 83 % of water 0 %-31.12.20240.6420ex3909509030 Preparation containing by weight: 16 % or more but not more than 20 % of ethoxylated polyurethane modified with hydrophobic groups, 19 % or more but not more than 23 % of diethylene glycol butyl ether, and 60 % or more but not more than 64 % of water 0 %-31.12.20240.6424ex3909509040 Preparation containing by weight: 34 % or more but not more than 36 % of ethoxylated polyurethane modified with hydrophobic groups, 37 % or more but not more than 39 % of propylene glycol, and 26 % or more but not more than 28 % of water 0 %-31.12.20240.6921ex3910000015Dimethyl, methyl(propyl(polypropylene oxide)) siloxane (CAS RN 68957-00-6), trimethylsiloxy-terminated0 %-31.12.20260.3260ex3910000020Block copolymer of poly(methyl-3,3,3-trifluoropropylsiloxane) and poly[methyl(vinyl)siloxane]0 %-31.12.20240.7057ex3910000025 Preparations containing by weight: 10 % or more, 2-hydroxy-3-[3-[1,3,3,3-tetramethyl-1-[(trimethylsilyl)oxy] disiloxanyl] propoxy] propyl-2-methyl-2-propenoate (CAS RN 69861-02-5), and 10 % or more, α-Butyldimethylsilyl- ω -3-[(2-methyl-1-oxo-2-propen-1-yl)oxy]propyl-terminated silicone polymer (CAS RN 146632-07-7) 0 %-31.12.2026 0.7058ex3910000035 Preparations containing by weight: 30 % or more, α -Butyldimethylsilyl- ω -(3-methacryloxy-2-hydroxypropyloxy)propyldimethylsilyl-polydimethylsiloxane (CAS RN 662148-59-6) and 10 % or more, N,N – Dimethylacrylamide (CAS RN 2680-03-7) 0 %-31.12.20260.4049ex3910000040Silicones of a kind used in the manufacture of long term surgical implants0 %-31.12.20260.7217ex3910000045Dimethyl siloxane, hydroxy-terminated polymer with a viscosity of 38-100 mPa·s (CAS RN 70131-67-8)0 %-31.12.20260.4300ex3910000050Silicone based pressure sensitive adhesive in solvent containing copoly(dimethylsiloxane/diphenylsiloxane) gum0 %-31.12.20270.7218ex3910000055

Preparation containing by weight: 55 % or more but not more than 65 % of vinyl terminated polydimethylsiloxane (CAS RN 68083-19-2), 30 % or more but not more than 40 % of dimethylvinylated and trimethylated silica (CAS RN 68988-89-6), and 1 % or more but not more than 5 % of silicic acid, sodium salt, reaction products with chlorotrimethylsilane and isopropyl alcohol (CAS RN 68988-56-7) 0 %-31.12.20260.4845ex3910000060Polydimethylsiloxane, whether or not polyethylene glycol and trifluoropropyl substituted, with methacrylate end groups0 %-31.12.20240.7953ex3910000065Liquid copolymer based on polydimethylsiloxane with terminal epoxide groups CAS RN 2102536-93-4)0 %-31.12.20250.5926ex3910000070Passivating silicon coating in primary form, to protect edges and prevent short circuits in semiconductor devices0 %-31.12.20240.8097ex3910000075Copolymer of 80 % dimethylsiloxane, 10 % methyl methacrylate and 10 % butyl acrylate in the form of a white powder0 %-31.12.20250.6324ex3910000080Monomethacryloxypropylterminated poly(dimethylsiloxane)0 %-31.12.2024 0.4413ex3911100081 Non-hydrogenated hydrocarbon resin, obtained by polymerization of more than 75 % by weight C-5 to C-12 cycloaliphatic alkenes and more than 10 % but not more than 25 % by weight aromatic alkenes yielding a hydrocarbon resin with: an iodine value of more than 120 and a Gardner Colour of more than 10 for the pure product or a Gardner Colour of more than 8 for a 50 % solution by weight in toluene (as determined by the ASTM method D6166) 0 %-31.12.20240.8220ex3911901915Polyetherimide of 4,4’-[(isopropylidene)bis(p-phenylenoxy)]diphthalic dianhydride and 1,3-benzenediamine or 1,4-benzenediamine (CAS RN 61128-46-9 or CAS RN 61128-47-0)0 %-31.12.20260.7163ex3911901920 Set of two components, in a volume ratio of 1:1, intended to produce a thermosetting polydicyclopentadiene after mixing, both components containing: 83 % or more by weight of 3a,4,7,7a-tetrahydro-4,7-methanoindene (dicyclopentadiene), a synthetic rubber, whether or not containing by weight 7 % or more of tricyclopentadiene. and each separate component containing: either an aluminium-alkyl compound, or an organic complex of tungsten or an organic complex of molybdenum 0 %-31.12.20240.4280ex3911901930Copolymer of ethyleneimine and ethyleneimine dithiocarbamate, in an aqueous solution of sodium hydroxide0 %-31.12.20270.5145ex3911901940m-Xylene formaldehyde resin0 %-31.12.20260.6519ex3911901970 Preparation, containing: Cyanic acid, C,C’-((1-methylethylidene)di–4,1-phenylene) ester, homopolymer (CAS RN 25722-66-1), 1,3-Bis(4-cyanophenyl)propane (CAS RN 1156-51-0), in a solution of butanone (CAS RN 78-93-3) with a content of less than 50 % by weight 0 %-31.12.2024 0.8450ex3911901980Poly(oxy-1,4-phenylenesulfonyl-1,4-phenylene) (CAS RN 25608-63-3 and CAS RN 25667-42-9) containing by weight not more than 20 % of additives0 %-31.12.20270.8218ex3911909923 Aqueous solution consisting of by weight 25 % or more, but not more than 40 % of a poly(isobutylene-maleic anhydride) modified with:

N,N-dimethylpropane-1,3-diamine, a copolymer of ethylene oxide and propylene oxide, having aminopropyl and methoxy end-groups, ethanol (CAS RN 497926-97-3) 0 %-31.12.20260.3257ex3911909925Copolymer of vinyltoluene and a-methylstyrene0 %-31.12.20240.5109ex3911909935Alternated copolymer of ethylene and maleic anhydride (EMA)0 %-31.12.20250.8009ex3911909938 Mixture containing by weight: 90 % (± 1 %) of 1,4:5,8- Dimethanonaphthalene, 2-ethylidene-1,2,3,4,4a,5,8,8a-octahydro-,polymer with 3a,4,7,7a- tetrahydro- 4,7-methano-1H-indene, hydrogenated (CAS RN 881025-72-5), and 10 % (± 1 %) of a hydrogenated styrene butadiene copolymer (CAS RN 66070-58-4) 0 %-31.12.20250.3221ex3911909940Mixed calcium and sodium salt of a copolymer of maleic acid and methyl vinyl ether, having a calcium content of 9 % or more but not more than 16 % by weight0 %-31.12.20240.3256ex3911909945Copolymer of maleic acid and methyl vinyl ether0 %-31.12.20240.8010ex3911909948 Mixture containing by weight: 90 % (± 1 %) of 1,4:5,8-dimethanonaphthalene, 2-ethylidene-1,2,3,4,4a,5,8,8a-octahydro-, polymer with 3a,4,7,7a-tetrahydro-4,7-methano-1H-indene, hydrogenated (CAS RN 881025-72-5), and 10 % (± 1 %) of an ethylene-propylene copolymer (CAS RN 9010-79-1) 0 %-31.12.20250.3255ex3911909965Calcium zinc salt of a copolymer of maleic acid and methyl vinyl ether0 %-31.12.2024 0.4091ex3911909986Copolymer of methyl vinyl ether and maleic acid anhydride (CAS RN 9011-16-9)0 %-31.12.20260.4912ex3912110030Cellulose triacetate (CAS RN 9012-09-3)0 %-31.12.20260.4953ex3912110040Cellulose diacetate powder0 %-31.12.20250.3251ex3912398510Ethylcellulose, not plasticized0 %-31.12.20240.3253ex3912398520Ethylcellulose, in the form of an aqueous dispersion containing hexadecan-1-ol and sodium dodecyl sulphate, containing by weight 27 (± 3) % of ethylcellulose0 %-31.12.20240.3252ex3912398530Cellulose, both hydroxyethylated and alkylated with alkyl chain-lengths of 3 or more carbon atoms0 %-31.12.20240.6718ex3912398550Polyquaternium 10 (CAS RN 68610-92-4)0 %-31.12.20250.4017ex3912901020Hydroxypropyl methylcellulose phthalate0 %-31.12.20240.3898ex3913900030Protein, chemically or enzymatically modified by carboxylation and/or phthalic acid addition, whether or not hydrolysed, having a weight average molecular weight (Mw) of less than 3500000 %-31.12.20240.3749ex3913900085Sterile sodium hyaluronate (CAS RN 9067-32-7)0 %-31.12.20240.3249ex3913900095Chondroitinsulphuric acid, sodium salt (CAS RN 9082-07-9)0 %-31.12.20240.8323ex3914000010 Aqueous suspension, containing by weight 20 % or more but not more than 30 % of beaded agarose, modified with nitrilotriacetic acid and loaded with divalent nickel ions (CAS RN 1615227-97-8), and 20 % or more but not more than 30 % of ethanol (CAS RN 64-17-5) 0 %-31.12.20270.4797ex3916200091 Profiles of poly(vinyl chloride) of a kind used in the manufacture of sheet pilings and facings, containing the following additives: titanium dioxide, poly(methyl methacrylate), calcium carbonate,

binding agents 0 %-31.12.2024 0.5988ex3916901010 Rods with cellular structure, containing by weight: polyamide-6 or poly(epoxy anhydride) 7 % or more but not more than 9 % of polytetrafluorethylene if present 10 % or more but not more than 25 % of inorganic fillers 0 %-31.12.20240.8116 ex39173100 ex39173200 ex39173900 30 20 20 Tubings: with an outer diameter of 0,33 mm or more but not more than 3,3 mm, with an inner diameter of 0,01 mm or more but not more than 2,1 mm, suitable for a maximum working pressure rate from 2,7 MPa up to 70 MPa, suitable for all solutions used in chromatography, whether or not with fused silica, whether or not covered with PEEK, for use in chromatographic system 0 %-31.12.20260.8268ex3917320030 Heat shrinkable tube: containing by weight 80 % or more polymer, with an insulation resistance of 90 MΩ or more, with a dielectric strength of 35 kV / mm or more, with a wall thickness of 0,04 mm or more, but not more than 0,9 mm, with a lay-flat width of 18 mm or more, but not more than 156 mm, for use in the manufacture of aluminium electrolytic capacitors 0 %-31.12.20240.8117ex3917400020 Plastic fittings (kit of nuts and ferrules or nuts) and connectors: threaded, supported with or without a stainless steel ring, suitable for a maximum working pressure rate of 2,7 MPa or more but not more than 114 MPa, for tubings with: outer diameter of 0,33 mm or more but not more than 3,3 mm, suitable for a maximum working pressure rate of 2,7 MPa or more but not more than 114 MPa, suitable for all solutions used in chromatography, for use in the production of chromatographic systems 0 %-31.12.2026 0.4641ex3917400091Plastic connectors containing O-rings, a retainer clip and a release system for insertion into car fuel hoses0 %-31.12.20240.2421 ex39191019 ex39191080 ex39199080 10 25 31 Reflecting film, consisting of a layer of polyurethane, with, on one side, security imprints against counterfeiting, alteration or substitution of data or duplication, or an official mark for an intended use, and embedded glass beads and, on the other side, an adhesive layer, covered on one side or on both sides with a release film0 %-31.12.20240.4800 ex39191080 ex39199080 27 20 Polyester film: coated on one side with an acrylic thermal release adhesive that debonds at temperatures of 90 °C or more but not more than 200 °C, and a polyester liner, and on the other side not coated or coated with an acrylic pressure sensitive adhesive or with an acrylic thermal release adhesive that debonds at temperatures of 90 °C or more but not more than 200 °C, and a polyester liner 0 %-31.12.20240.2910ex3919108035Reflecting film, consisting of a layer of poly(vinyl chloride), a layer of alkyd polyester, with, on one side, security imprints against counterfeiting, alteration or substitution of data or duplication, or an official mark for an intended use, only visible by means of a retroreflecting lighting, and embedded glass beads and, on the other side, an adhesive layer, covered on one side or on both sides with a release film0 %-31.12.20240.4757ex3919108037

Polytetrafluoroethylene film: with a thickness of 100 µm or more, an elongation at break of not more than 100 %, coated on one side with a pressure sensitive silicon adhesive 0 %-31.12.20250.4303 ex39191080 ex39199080 45 45 Reinforced polyethylene foam tape, coated on both sides with an acrylic micro channelled pressure sensitive adhesive and on one side a liner, with an application thickness of 0,38 mm or more but not more than 1,53 mm0 %-31.12.2027 0.8109ex3919108048 Plastic strips of polypropylene, self-adhesive, unilaterally adhesive-coated with an Acrylic Polymer, in rolls with a width of 20 cm or less, with a thickness including adhesion layer of 0,03 mm or less, for use in the manufacturing of lithium-ion electric rechargeable batteries 3,2 %-31.12.20240.3035 ex39191080 ex39199080 ex39201089 50 41 25 Adhesive film consisting of a base of a copolymer of ethylene and vinyl acetate (EVA) of a thickness of 70 µm or more and an adhesive part of acrylic type of a thickness of 5 µm or more, for use in the grinding and/or dicing process of silicon discs0 %-31.12.20240.3036 ex39191080 ex39199080 55 53 Acrylic foam tape, covered on one side with a heat activatable adhesive or an acrylic pressure sensitive adhesive and on the other side with an acrylic pressure sensitive adhesive and a release sheet, of a peel adhesion at an angle of 90 o of more than 25 N/cm (as determined by the ASTM D 3330 method)0 %-31.12.20270.2416 ex39191080 ex39199080 ex39206100 57 30 30 Reflecting sheet: of a polycarbonate or acrylic polymer film embossed on one side in a regular shaped pattern covered on one or both sides with one or more layers of plastic or metallisation, and whether or not covered on one side with a self-adhesive layer and a release sheet 0 %-31.12.20240.6886ex3919108063 Reflecting film consisting of a layer of an acrylic resin with imprints against counterfeiting, alteration or substitution of data or duplication, or an official mark for an intended use, a layer of an acrylic resin having embedded glass beads, a layer of an acrylic resin hardened by a melamine cross-linking agent, a metal layer, an acrylic adhesive, and a release film 0 %-31.12.2025 0.4545 ex39191080 ex39199080 73 50 Self-adhesive reflecting sheet whether or not in segmented pieces, whether or not containing a watermark, with or without an application tape coated on one side with an adhesive; the reflective sheet consists of: a layer of acrylic or vinyl polymer, a layer of poly(methyl methacrylate) or polycarbonate containing microprisms, a layer of metallisation, an adhesive layer, and a release sheet whether or not containing an additional layer of polyester 0 %-31.12.20240.5166 ex39191080 ex39199080 75 80 Self-adhesive reflecting film, consisting of several layers including: a copolymer of acrylic resin, polyurethane, a metallised layer with, on one side, laser imprints against counterfeiting, alteration or substitution of data or duplications, or an official mark for an intended use, glass microspheres, and

an adhesive layer, with a release liner on one or both sides 0 %-31.12.20260.4799 ex39191080 ex39199080 85 28 Poly(vinyl chloride), poly(ethyleneterephthalate), polyethylene or any other polyolefin film: coated on one side with an acrylic UV-sensitive adhesive and a liner of a total thickness of 65 µm or more without release liner 0 %-31.12.20240.4414ex3919908019 Transparent poly(ethylene terephthalate) self-adhesive film: free from impurities or faults, coated on one side with an acrylic pressure sensitive adhesive and a protective liner, and on the other side with an antistatic layer of ionic organic choline compound, whether or not with a printable dust-proof layer of modified long chain alkyl organic compound, with a total thickness without the liner of 54 µm or more but not more than 64 µm, and a width of more than 1295 mm but not more than 1305 mm 0 %-31.12.2024 0.4314ex3919908022Polyester, polyethylene or polypropylene film coated on one or both sides with an acrylic and/or rubber pressure sensitive adhesive, whether or not supplied with a release liner, put up in rolls of a width of 45,7 cm or more but not more than 160 cm0 %-31.12.20240.3243ex3919908023Film consisting of 1 to 3 laminated layers of poly(ethylene terephthalate) and a copolymer of terephthalic acid, sebacic acid and ethylene glycol, coated on one side with an acrylic abrasion resistant coating and on the other side with an acrylic pressure sensitive adhesive, a water soluble methylcellulose coating and a poly(ethylene terephthalate) protective liner0 %-31.12.20240.4760ex3919908024 Reflecting laminated sheet: consisting of an epoxy acrylate layer embossed on one side in a regular shaped pattern, covered on both sides with one or more layers of plastic material and covered on one side with an adhesive layer and a release sheet 0 %-31.12.20240.4415ex3919908033Transparent poly(ethylene) self-adhesive film, free from impurities or faults, coated on one side with an acrylic pressure sensitive adhesive, with a thickness of 60 µm or more, but not more than 70 µm, and with a width of more than 1245 mm but not more than 1255 mm0 %-31.12.20240.4398ex3919908035 Reflecting layered sheet on rolls, with a width of more than 20 cm, showing an embossed regular pattern, consisting of poly(vinyl chloride) film coated on one side with: a layer of polyurethane containing glass micro beads, a layer of poly(ethylene vinyl acetate), an adhesive layer, and a release sheet 0 %-31.12.20240.7503ex3919908037 Polyethylene or polycarbonate film, cut into ready to use forms, one side partly printed whereby part of the printing either gives information about the meaning of LED’s visible at the unprinted areas, or marks those points which must be touched to operate the system, the other side partly covered with an adhesive layer, both sides covered with a release liner, and with dimensions of not more than 14 cm x 2,5 cm, for use in the manufacture of push-button switches for mechatronic system adjustable furniture

0 %-31.12.2024 0.4445ex3919908049Reflecting laminated sheet consisting of a film of poly(methyl methacrylate) embossed on one side in a regular shaped pattern, a film of a polymer containing glass microspheres, an adhesive layer and a release sheet0 %-31.12.20240.5507ex3919908051Biaxially-oriented film of poly(methyl methacrylate), of a thickness of 50 µm or more but not exceeding 90 µm, covered on one side with an adhesive layer and a release sheet0 %-31.12.20240.4532ex3919908054 Poly(vinyl chloride) film, on one side covered with a polymer layer an adhesive layer a release liner, on one side embossed, containing oblate spheres; whether or not on the other side covered with an adhesive layer and a metallised polymer layer 0 %-31.12.20240.4947ex3919908065Self-adhesive film with a thickness of 40 µm or more, but not more than 475 µm, consisting of one or more layers of transparent, metallised or dyed poly(ethylene terephthalate), covered on one side with a scratch resistant coating and on the other side with a pressure sensitive adhesive and a release liner0 %-31.12.20250.4925ex3919908070Self-adhesive polishing discs of microporous polyurethane, whether or not coated with a pad0 %-31.12.20250.4964ex3919908082 Reflecting film consisting of: a polyurethane layer, a glass microspheres layer, a metallised aluminium layer, and an adhesive, covered on one or both sides with a release liner, whether or not a poly(vinyl chloride) layer, a layer whether or not incorporating security imprints against counterfeiting, alteration or substitution of data or duplication, or an official mark for an intended use 0 %-31.12.20250.4459ex3919908083 Reflector or diffuser sheets, in rolls, for protection against ultraviolet or infra-red heat radiation, to be affixed to windows or for equal transmission and distribution of light, intended for LCD modules 0 %-31.12.2027 0.3241ex3920102530 Mono-layered High-Density Polyethylene film: containing by weight 99 % or more of polyethylene, with a thickness of 12 µm or more but not more than 20 µm, with a length of 4000 m or more but not more than 7000 m, with a width of 600 mm or more but not more than 900 mm 0 %-31.12.20240.8440ex3920102820 A Separator film of polyethylene: coated on one side with a layer of aluminium oxide, containing by weight not more than 70 % of polyethylene, containing by weight not more than 30 % of aluminum oxide, with a total thickness of 5 µm or more but not more than 25 µm, for use in the manufacture of lithium-ion batteries 3,2 %-31.12.20240.4419ex3920102891 Poly(ethylene) film printed with a graphic design, which is achieved by using four base colours in ink plus specialist colours, to achieve multiple colours in ink on one side of the film, and one colour on the opposite side, the graphic design also has the following characteristics: is repetitive and equally spaced along the length of the film is equally and visibly aligned when viewed from the back or front of the film 0 %-31.12.20240.6640ex3920104040

Tubular layered film predominately of polyethylene: consisting of a tri-layer barrier with a core layer of ethylene vinyl alcohol covered on either side with a layer of polyamide, covered on either side with at least one layer of polyethylene, having a total thickness of 55 µm or more, having a diameter of 500 mm or more but not more than 600 mm 0 %-31.12.20250.3754ex3920108940Composite sheet containing an acrylic coating and laminated to a high-density polyethylene layer, of a total thickness of 0,8 mm or more but not more than 1,2 mm0 %-31.12.20270.8149ex3920108945Octene and ethylene copolymer plastic film of a thickness of 0,45 mm or more but not more than 0,75 mm, for use in the manufacture of glass to glass photovoltaic solar panels0 %-31.12.2027 0.5139ex3920108955 Ethylene vinyl acetate (EVA) film: with a raised relief surface with embossed undulations, not laminated, not cross-linked, and with a thickness of more than 0,3 mm 0 %-31.12.20260.5482ex3920202140 Sheets of biaxially - oriented polypropylene film: with the thickness of not more than 0,1 mm, printed on both sides with specialised coatings to allow banknote security printing 0 %-31.12.20240.8205ex3920202150Biaxialy oriented film of multiple layers of polypropylene, with a total thickness of not more than 14 micron0 %-31.12.20260.4394ex3920202960 Mono-axial oriented film, of a total thickness of not more than 75µm, consisting of three or four layers, each layer containing a mixture of polypropylene and polyethylene, with a core layer whether or not containing titanium dioxide, having: a tensile strength in the machine direction of 120 MPa or more but not more than 270 MPa and a tensile strength in the transverse direction of 10 MPa or more but not more than 40 MPa as determined by test method ASTM D882/ISO 527-3 0 %-31.12.20240.3028ex3920202970 Mono-axial oriented film, consisting of three layers, each layer consisting of a mixture of polypropylene and a copolymer of ethylene and vinyl acetate, with a core layer whether or not containing titanium dioxide, having: a thickness of 55 µm or more but not more than 97 µm, a tensile modulus in the machine direction of 0,30 GPa or more but not more than 1,45 GPa, and a tensile modulus in the transverse direction of 0,20 GPa or more but not more than 0,70 GPa 0 %-31.12.20240.5167ex3920202994 Mono-axial oriented, co-extruded film: consisting of 3 to 5 layers, each layer mainly consisting of polypropylene and/or polyethylene, each layer containing not more than 10 % by weight of other polymers, whether or not containing titanium dioxide in the core layer, of an overall thickness of not more than 75 µm 0 %-31.12.2027 0.3024ex3920431092Sheeting of poly(vinyl chloride), stabilized against ultraviolet rays, without any holes, even microscopic, of a thickness of 60 µm or more but not more than 80 µm, containing 30 or more but not more than 40 parts of plasticiser to 100 parts of poly(vinyl chloride)0 %-31.12.20240.3235 ex39204310 ex39204910 94 93 Film of a specular gloss of 70 or more, measured at an angle of 60 ° using a glossmeter (as determined by the ISO 2813:2000 method), consisting of one or two layers of poly(vinyl chloride) coated on both sides with a layer of plastic, of a thickness of 0,26 mm or more but not more than 1,0 mm, covered on the gloss surface with a protective film of polyethylene, in rolls of a width of 1000 mm or more but not more than 1450 mm, for use in the manufacture of goods of heading 94030 %-31.12.20240.3026ex3920431095Reflecting laminated sheet, consisting of a film of poly(vinyl chloride) and a film of an other plastic totally embossed in a regular pyramidal pattern, covered on one side with a release sheet0 %-31.12.20240.5930ex3920491030

Film of a (polyvinyl)chloride-copolymer containing by weight 45 % or more of fillers on a support 0 %-31.12.20240.3021ex3920510020Plate of poly(methyl methacrylate) containing aluminium trihydroxide, of a thickness of 3,5 mm or more but not more than 19 mm0 %-31.12.20240.5506ex3920510030Biaxially-oriented film of poly(methyl methacrylate), of a thickness of 50 µm or more but not exceeding 125 µm0 %-31.12.20240.5753ex3920510040Sheets of polymethylmethacrylate conforming to standard EN 4366 (MIL-PRF-25690)0 %-31.12.20240.7949ex3920610040 Extruded thermoplastic foils or films of polycarbonate with: matt surface texture on both sides a thickness of more than 50 µm but not more than 200 µm, a width of 800 mm or more, but not more than 1500 mm, and a length of 300 m or more, but not more 2500 m 0 %-31.12.2025 0.8274ex3920610050 Coextruded film of polycarbonate main layer and polymethyl methacrylate top layer with a: total thickness of more than 230 µm but not more than 270 µm, top layer thickness of more than 40 µm but not more than 55 µm, defined surface roughness of the top layer of 0,5 µm or less (according to ISO 4287), UV-stabilized top layer 0 %-31.12.20260.7418 ex39206219 ex39206290 05 10 Poly(ethylene terephthalate) film in rolls: with a thickness of 0,335 mm or more but not more than 0,365 mm, and coated with a gold layer with a thickness of 0,03 µm or more but not more than 0,06 µm 0 %-31.12.20270.3234ex3920621908 Poly(ethylene terephthalate) film, not coated with an adhesive, of a thickness of not more than 25 µm, either: only dyed in the mass, or dyed in the mass and metallised on one side 0 %-31.12.20240.3017ex3920621912Film of poly(ethylene terephthalate) only, of a total thickness of not more than 120 µm, consisting of one or two layers each containing a colouring and/or UV-absorbing material throughout the mass, uncoated with an adhesive or any other material0 %-31.12.20240.3022ex3920621918Laminated film of poly(ethylene terephthalate) only, of a total thickness of not more than 120 µm, consisting of one layer which is metallised only and one or two layers each containing a colouring and/or UV-absorbing material throughout the mass, uncoated with an adhesive or any other material0 %-31.12.20240.3034ex3920621920Reflecting polyester sheeting embossed in a pyramidal pattern, for the manufacture of safety stickers and badges, safety clothing and accessories thereof, or of school satchels, bags or similar containers0 %-31.12.2024 0.8438ex3920621928 Non-transparent film of poly(ethylene terephthalate) or poly(vinyl difluoride): each outer layer with a thickness of 7 µm or more but not more than 80 µm, with a tensile strength of 300 N/cm2 or more (ASTM D-882), with a total thickness of 200 µm or more but not more than 350 µm, and with a width of 600 mm or more but not more than 1600 mm, covered on one side with a layer of a fluoropolymer, and on the other side with an adhesive and a layer of polyvinylidene difluoride, or coated on both sides with polyvinylidene difluoride or polyvinyl fluoride based on fluorinated polymer composites

0 %-31.12.20270.4520ex3920621932 Transparent poly(ethylene terephthalate) film: having thickness of both sides of 7 nm or more but not more than 80 nm, or thickness of both sides of 7 µm or more but not more than 80 µm, whether coated with an acrylic-based organic material or not, with a surface tension of 36 Dyne/cm or more but not more than 39 Dyne/cm, or transparent 3 or 4 layers, second layer of PET, and other layers contain fluorine resin, with a light transmittance of more than 80 %, with a haze value of not more than 1,3 %, with a total thickness of 10 µm or more but not more than 350 µm, with a width of 800 mm or more but not more than 1600 mm 0 %-31.12.20280.3356ex3920621938Poly(ethylene terephthalate) film, of a thickness of not more than 12 µm, coated on one side with a layer of aluminium oxide of a thickness of not more than 35 nm0 %-31.12.20240.3357ex3920621948 Sheets or rolls of poly(ethylene terephthalate): coated on both sides with a layer of epoxy acrylic resin, of a total thickness of 37 µm (± 3 µm) 0 %-31.12.2025 0.2589ex3920621952Film of polyethylene terephthalate, polyethylene naphthalate or similar polyester, coated on one side with metal and/or metal oxides, containing by weight less than 0,1 % of aluminium, of a thickness of not more than 300 µm and having a surface resistivity of not more than 10000 ohms (per square) (as determined by the ASTM D257 method)0 %-31.12.20240.4344ex3920621960 Poly(ethylene terephthalate) film: of a thickness of not more than 20 µm, coated on at least one side with a gas barrier layer consisting of a polymeric matrix in which silica or aluminium oxide has been dispersed and of a thickness of not more than 2µm 0 %-31.12.20270.8011 ex39206219 ex39206290 68 20 Poly(ethylene terephthalate) film in rolls: with a thickness of 50 µm or more but not more than 350 µm, and covered with a layer of sputtered precious metal such as gold or palladium with a thickness of 0,02 µm or more but not more than 0,06 µm 0 %-31.12.20250.3328ex3920690020Film of poly(ethylene naphthalene-2,6-dicarboxylate)0 %-31.12.20240.7882ex3920690030 Mono- or multilayer, transverse oriented, shrink film: composed of more than 85 % by weight of polylactic acid, not more than 5 % by weight of inorganic or organic additives and not more than 10 % by weight of additives based on biodegradable polyesters, with a thickness of 20 µm or more but not more than 100 µm, with a length of 2385 m or more but not more than 9075 m, biodegradable and compostable (as determined by the method EN 13432) 0 %-31.12.20240.6483ex3920690050 Monolayer, biaxially oriented film: composed of more than 85 % by weight of poly(lactic acid) and not more than 10,50 % by weight of modified poly(lactic acid) based polymer, poly-glycol ester and talc, having a thickness of 20 µm or more but not more than 120 µm biodegradable and compostable (as determined by the method EN 13432) 0 %-31.12.2024 0.6484ex3920690060 Monolayer, transverse oriented, shrink film: composed of more than 80 % by weight of poly(lactic acid) and not more than 15,75 % by weight of additives of modified poly(lactic acid),

having a thickness of 45 µm or more but not more than 50 µm, biodegradable and compostable (as determined by the method EN 13432) 0 %-31.12.20240.7883ex3920690070 Mono- or multilayer, biaxially oriented film: composed of more than 85 % by weight of polylactic acid, not more than 5 % by weight of inorganic or organic additives, and not more than 10 % by weight of additives based on biodegradable polyesters, with a thickness of 9 µm or more but not more than 120 µm, with a length of 1395 m or more but not more than 21560 m, biodegradable and compostable (as determined by the method EN 13432) 0 %-31.12.20240.6515ex3920791010Sheets of painted vulcanised fibre-board with a thickness of not more than 1,5 mm0 %p/st31.12.20240.4766ex3920910052 Poly(vinyl butyral) film: containing by weight 26 % or more but not more than 30 % of triethyleneglycol bis(2-ethyl hexanoate) as a plasticiser, with a thickness of 0,73 mm or more but not more than 1,50 mm 0 %-31.12.20240.3329ex3920910091Poly(vinyl butyral) film having a graduated coloured band3 %-31.12.20240.3136ex3920910093 Film of poly(ethylene terephthalate), whether or not metallised on one or both sides, or laminated film of poly(ethylene terephthalate) films, metallised on the external sides only, and having the following characteristics: a visible light transmission of 50 % or more, coated on one or both sides with a layer of poly(vinyl butyral) but not coated with an adhesive or any other material except poly(vinyl butyral), a total thickness of not more than 0,2 mm without taking the presence of poly(vinyl butyral) into account and a thickness of poly(vinyl butyral) of more than 0,2 mm 0 %-31.12.2024 0.4508ex3920910095Co-extruded trilayer poly(vinyl butyral) film with a graduated colour band containing by weight 29 % or more but not more than 31 % of 2,2’-ethylenedioxydiethyl bis(2-ethylhexanoate) as a plasticiser0 %-31.12.20240.3917ex3920992840 Polymer film containing the following monomers: poly (tetramethylene ether glycol), bis (4-isocyanotocyclohexyl) methane, 1,4-butanediol or 1,3-butanediol, with a thickness of 0,25 mm or more but not more than 5,0 mm, embossed with a regular pattern on one surface, and covered with a release sheet 0 %-31.12.20240.5938ex3920992845 Transparent polyurethane film metallised on one side: with a gloss of more than 90 degrees according to ASTM D2457 covered on the metallised side with a heat bonding adhesive layer consisting of polyethylene/polypropylene copolymer covered on the other side with a protective poly(ethylene terephthalate) film with a total thickness of more than 204 µm but not more than 244 µm 0 %-31.12.20240.8005ex3920992848 Thermoplastic polyurethane foil in rolls, with: a width of 900 mm or more but not more than 1016 mm, a matt finish, a thickness of 0,4 mm (± 8 %), an elongation at break of 480 % or more (ASTM D412 (Die C)), a tensil strength in machine direction of 470 (± 10) kg/cm2 (ASTM D412 (Die C)), a Shore A hardness of 90 (± 3) (ASTM D2240), a tear strength of 100 (± 10) kg/cm2 (ASTM D624 (Die C)),

a melting point of 165°C (± 10 °C) 0 %-31.12.20250.4192ex3920992850Thermoplastic polyurethane film, of a thickness of 250 µm or more but not more than 350 µm, covered on one side with a removable protective film0 %-31.12.2026 0.6579ex3920992865 Matt, thermoplastic polyurethane foil in rolls with: a width of 1640 mm (± 10 mm), a gloss of 3,3 degrees or more but not more than 3,8 (as determined by the method ASTM D2457), a surface roughness of 1,9 Ra or more but not more than 2,8 Ra (as determined by the method ISO 4287), a thickness of more than 365 µm but not more than 760 µm, a hardness of 90 (± 4) (as determined by the method: Shore A (ASTM D2240)), an elongation to break of 470 % (as determined by the method: EN ISO 527) 0 %m231.12.20240.5315ex3920992870 Sheets on rolls, consisting of epoxy resin, with conducting properties, containing: microspheres with a coating of metal, whether or not alloyed with gold, an adhesive layer, with a protective layer of silicone or poly(ethylene terephthalate) on one side, with a protective layer of poly(ethylene terephthalate) on the other side, and with a width of 5 cm or more but not more than 100 cm with a length of not more than 2000 m 0 %-31.12.20260.3326ex3920995925Poly(1-chlorotrifluoroethylene) film0 %-31.12.20240.7603ex3920995930Poly(tetrafluoroethylene) film containing by weight 10 % or more of graphite0 %-31.12.20240.2873ex3920995955Ion-exchange membranes of fluorinated plastic material0 %-31.12.20240.3135ex3920995965Film of a vinyl alcohol copolymer, soluble in cold water, of a thickness of 34 µm or more but not more than 90 µm, a tensile strength at break of 20 MPa or more but not more than 55 MPa and an elongation at break of 250 % or more but not more than 900 %0 %-31.12.20240.7529ex3920995975 Film of fluorinated ethylene propylene resin (CAS RN 25067-11-2) with: a thickness of 0,010 mm or more but not more than 0,80 mm, a width of 1219 mm or more but not more than 1575 mm, and a melting point of 252 °C (measured according ASTM D-3418) 0 %-31.12.2024 0.4095ex3920999020Anisotropic conductive film, in rolls, of a width of 1,2 mm or more but not more than 3,15 mm and a maximum length of 300 m, used for joining electronic components in the production of LCD or plasma displays0 %-31.12.20240.3318ex3921131010Sheet of polyurethane foam, of a thickness of 3 mm (± 15 %) and of a specific gravity of 0,09435 or more but not more than 0,100920 %m331.12.20240.6066ex3921190030 Blocks with cellular structure, containing by weight: polyamide-6 or poly(epoxy anhydride) 7 % or more but not more than 9 % of polytetrafluorethylene if present 10 % or more but not more than 25 % of inorganic fillers 0 %-31.12.20240.6911ex3921190040 Transparent, microporous, acrylic acid grafted polyethylene film, in the form of rolls, with: a width of 98 mm or more but not more than170 mm, a thickness of 15 µm or more but not more than 36 µm, of a kind used for the manufacture of alkaline battery separators 3,2 %-31.12.20240.7263ex3921190045

Microporous monolayer film of polypropylene or a microporous trilayer film of polypropylene, polyethylene and polypropylene, each film with: zero transversal production direction (TD) shrinkage, a total thickness of 8 µm or more, but not more than 50 µm, a width of 15 mm or more, but not more than 900 mm, a length of more than 200 m, but not more than 8000 m, an average pore size between 0,02 µm and 0,1 µm, laminated or not with a Polypropylene non-woven mat of 50 to 200 µm thickness, coated or not with surfactant, coated or not on 1 or 2 sides with a ceramic layer of min 1 µm thickness or more, but not more than 5 µm, coated or not on 1 or 2 sides with a sticky binder, PVdF type or similar of min 0,5 µm thickness or more, but not more than 5 µm 3,2 %-31.12.2024 0.7132ex3921190050 Porous membrane of polytetrafluorethylene (PTFE) laminated to a polyester spunbonded non-woven cloth with a total thickness of more than 0,05 mm but not more than 0,20 mm, a water entry pressure between 5 and 200 kPa according to ISO 811, and an air permeability of 0,08 cm3/cm2/s or more according to ISO 5636-5 0 %-31.12.20260.7280ex3921190060 Multi-porous multilayer separator foil with: one microporous polyethylene layer between two microporous polypropylene layers and whether or not containing a coating of aluminium oxide on both sides, a width of 65 mm or more but not more than 170 mm, a total thickness of 0,01 mm or more but not more than 0,03 mm, a porosity of 0,25 or more but not more than 0,65 0 %m231.12.20270.3314ex3921190093Strip of microporous polytetrafluoroethylene on a support of a non-woven, for use in the manufacture of filters for kidney dialysis equipment0 %-31.12.20240.3002ex3921190095Film of polyethersulfone, of a thickness of not more than 200 µm0 %-31.12.20240.3003ex3921901010Composite plate of poly(ethylene terephthalate) or of poly(butylene terephthalate), reinforced with glass fibres0 %-31.12.20240.4379ex3921901020Poly(ethylene terephthalate) film, laminated on one side or on both sides with a layer of unidirectional nonwoven poly(ethylene terephthalate) and impregnated with polyurethane or epoxide resin0 %-31.12.20240.6156ex3921901030 Multilayer film consisting of: a poly(ethylene terephthalate) film with a thickness of more than 100 µm but not more than 150 µm, a primer of phenolic material with a thickness of more than 8 µm but not more than 15 µm, an adhesive layer of a synthetic rubber with a thickness of more than 20 µm but not more than 30 µm, and a transparent poly(ethylene terephthalate) liner with a thickness of more than 35 µm but not more than 40 µm 0 %m231.12.2024 0.4844ex3921905525Prepreg sheets or rolls containing polyimide resin0 %-31.12.20240.7510ex3921905535Glass fiber impregnated with epoxy resin for use in the manufacture of smart cards0 %m231.12.20240.6742ex3921905540 Three layered fabric sheet, in rolls, comprising a core layer of 100 % Nylon Taffeta or Nylon/Polyester blended Taffeta, coated on both sides with polyamide, of a total thickness not more than 135 µm,

of a total weight not more than 80 g/m2 0 %m231.12.20250.8291ex3921905560 Membrane composed of a polyamide layer and a polysulfone layer on a cellulose support layer with: a total thickness of 0,25 mm or more but not more than 0,40 mm, a total weight of 109 g/m2 or more but not more than 114 g/m2 0 %m231.12.20260.3312ex3921906035Ion-exchange membranes based on a fabric coated on both sides with fluorinated plastic material, for use in chlor-alkali electrolytic cells0 %-31.12.20240.5396ex3923109010 Photomask or wafer compacts: consisting of antistatic materials or blended thermoplastics proving special electrostatic discharge (ESD) and outgassing properties, having non porous, abrasion resistant or impact resistant surface properties, fitted with a specially designed retainer system that protects the photomask or wafers from surface or cosmetic damage and with or without a gasket seal, of a kind used in the photolithography or other semiconductor production to house photomasks or wafers 0 %-31.12.20260.7630ex3926300040Plastic internal door handle used in the manufacture of motor vehicles0 %-31.12.2024 0.7335 ex39263000 ex39269097 50 48 Coated interior or exterior decorative parts consisting of: a copolymer of acrylonitrile-butadiene-styrene (ABS), whether or not mixed with polycarbonate, and a PVC foil, not containing layers of copper, nickel or chromium, for use in the manufacturing of parts for motor vehicles of heading 8701 to 8705 0 %p/st31.12.20270.2764ex3926909710Microspheres of a polymer of divinylbenzene, of a diameter of 4,5 µm or more but not more than 80 µm0 %-31.12.20240.3756ex3926909715Glass fibre reinforced plastic traverse leaf spring for use in the manufacture of motor vehicle suspension systems0 %-31.12.20240.2978ex3926909720Reflecting sheeting or tape, consisting of a facing-strip of poly(vinyl chloride) embossed in a regular pyramidal pattern, heat-sealed in parallel lines or in a grid-pattern to a backing-strip of plastic material, or of knitted or woven fabric covered on one side with plastic material0 %-31.12.20240.6717ex3926909723Plastic cover with clips for the exterior rear-view mirror of motor vehicles0 %p/st31.12.20250.7445ex3926909727Gasket of polyethylene foam, intended to fill-up the space between the body of a motor vehicle and the base of a rear-view mirror0 %-31.12.20240.5474ex3926909730 Parts of car radio and car air-conditioner front panels of acrylonitrile-butadiene-styrene with or without polycarbonate, coated with a copper, a nickel and a chrome layers, with a total thickness of coating of 5,54 µm or more but not more than 49,6 µm 0 %-31.12.20260.6301ex3926909733Housings, housing parts, drums, setting wheels, frames, covers, upper part, design plate and other parts of acrylonitrile-butadiene-styrene, polycarbonate, polymethylmethacrylate or thermoplastic polyurethane, of a kind used for the manufacture of remote controls0 %p/st31.12.20240.7061ex3926909740Silicone shell for breast implant0 %-31.12.2026 0.3850ex3926909743Mixture of water and by weight 19 % or more but not more than 35 % of expanded hollow microspheres of a copolymer of acrylonitrile, methacrylonitrile and isobornyl methacrylate or other methacrylate, of a diameter of 3 µm or more but not more than 4,95 µm0 %-31.12.20240.6166ex3926909750Knob of car radio front panel, made of Bisphenol A-based polycarbonate, in immediate packings of not less than 300 pieces0 %p/st31.12.20240.8118ex3926909758

Plastic ferrules and/or plugs: supported with or without a stainless steel ring, suitable for a maximum working pressure rate of 2,7 MPa or more but not more than 114 MPa, for tubings with: outer diameter of 0,33 mm or more but not more than 3,3 mm, suitable for a maximum working pressure rate of 2,7 MPa or more but not more than 114 MPa, suitable for all solutions used in chromatography, for use in the production of chromatographic systems 0 %-31.12.20260.7196ex3926909777Silicone decoupling ring with an inner diameter of 14,7 mm or more but not more than 16,0 mm, in immediate packings of 2500 pieces or more, of a kind used in car parking aid sensor systems0 %p/st31.12.20260.3046ex4007000010Siliconated vulcanised rubber thread and cord0 %-31.12.20240.8504 ex40093100 ex40093200 10 20 Multilayered rubber pipe, reinforced with aramide fabric, whether or not having polyamide connection elements and steel clamps, for use in the manufacture of automotive heat exchangers and/or condenser in automotive air conditioning systems0 %-31.12.20270.6708ex4009420020 Rubber brake hose with: textile strings, a wall thickness of 3,2 mm, a metal hollow terminal pressed on both ends, and one or more mounting brackets, for use in the manufacture of goods of Chapter 87 0 %-31.12.2025 0.7042 ex40103100 ex40103300 ex40103900 10 10 10 Vulcanized rubber endless transmission belt of trapezoidal cross-section (V-belts) with longitudinal V-ribbed pattern on the inner side for use in the manufacture of goods of Chapter 870 %-31.12.20240.6844ex4016930030 Rectangular ethylene-propylene-diene rubber gasket, with: a length of 72 mm or more but not more than 825 mm, a width of 18 mm or more but not more than 155 mm, a peak temperature of 150°C or more but not more than 240°C, a permissible material outflow at the place of the mold split of not more than 0,3 mm 0 %-31.12.20250.7170ex4016995710 Air intake hose for air supply to the combustion part of the engine comprising at least: one flexible rubber hose, one plastic hose, and metal clips, whether or not a resonator for use in the manufacture of goods of Chapter 87 0 %p/st31.12.20260.7357ex4016995730 Pin boot of a brake calliper made of vulcanized rubber with: an inner diameter of not less than 5 mm and an outer diameter of not more than 35 mm, a height of 15 mm or more, but not more than 40 mm, and a ribbed design for use in the manufacture of goods of Chapter 87 0 %-31.12.20240.5148ex4016999730Tyre moulding bladder0 %-31.12.20260.5842ex4104411910Buffalo leather, split, chrome tanned synthetic retanned (crust), dry0 %-31.12.20240.2555 41051000 41053090 Sheep or lamb skin leather, without wool on, tanned or retanned but not further prepared, whether or not split, other than leather of heading 41140 %-31.12.20240.2553 41062100 41062290 Goat or kid skin leather, without hair on, tanned or retanned but not further prepared, whether or not split, other than leather of heading 41140 %-31.12.2024 0.2554 41063100 41063200 41064090 41069200

Leather of other animals, without hair on, not further prepared than tanned, other than leather of heading 41140 %-31.12.20240.6223ex4408393010 Okoume veneer sheets: of a length of 1270 mm or more, but not more than 3200 mm, of a width of 150 mm or more, but not more than 2000 mm, of a thickness of 0,5 mm or more, but not more than 4 mm, not sanded and not planed 0 %-31.12.20240.8372ex4411129210 Fibreboard: with a thickness of 2,20 mm or more but not more than 2,80 mm, with a density of 0,95 g/cm3 or more, lacquered or coated with melamine foil on both sides, and with dimensions of 1300 mm x 1100 mm or less, used in the manufacture of printed circuit boards 0 %-31.12.20270.4217ex5004001010Silk yarn (other than yarn spun from silk waste) not put up for retail sale, unbleached, scoured or bleached, entirely of silk0 %-31.12.20260.2551 ex50050010 ex50050090 10 10 Yarn spun entirely from silk waste (noil), not put up for retail sale0 %-31.12.20240.254452081110Fabrics for the manufacture of bandages, dressings and medical gauzes5,2 %-31.12.20240.7372ex5311009010 Plain-woven fabric of paper yarns glued on a tissue paper layer: with a weight of 190 g/m2 or more but not more than 280 g/m2, and cut into rectangles with a side length of 40 cm or more but not more than 140 cm 0 %-31.12.20270.7515ex5311009020 Sisal cloth in rolls with; a length of 20 metres or more but not more than 30 metres and a maximum width of 2,5 metres for use in the production of Stainless Steel Kitchenware 0 %-31.12.2024 0.7608ex5402440010 Synthetic elastomeric filament yarn: untwisted or with a twist not exceeding 50 turns per metre, measuring 300 dtex or more but not more than 1000 dtex, composed of polyurethane ureas based on a copolyether glycol of tetrahydrofuran and 3-methyltetrahydrofuran, for use in the manufacture of disposable hygiene products of heading 9619 0 %-31.12.20240.2975ex5402490030Yarn of a copolymer of glycollic acid with lactic acid, for the manufacture of surgical sutures0 %-31.12.20240.3098ex5402490050Non-textured filament yarn of poly(vinyl alcohol)0 %-31.12.20240.3096ex5402490070Synthetic filament yarn, single, containing by weight 85 % or more of acrylonitrile, in the form of a wick containing 1000 continuous filaments or more but not more than 25000 continuous filaments, of a weight per metre of 0,12 g or more but not more than 3,75 g and of a length of 100 m or more, for the manufacture of carbon-fibre yarn0 %m31.12.20240.8108ex5403310010Continuous viscose rayon filament yarn of 105 dtex or more but not more than 117 dtex, and consisting of 36 monofilaments or more but not more than 40 monofilaments0 %-31.12.20250.2481ex5404190050Monofilaments of polyester or poly(butylene terephthalate), with cross-sectional dimension of 0,5 mm or more but not more than 1 mm, for use in the manufacture of zippers0 %-31.12.20240.8225ex5404190060 Chemically tapered synthetic filaments of polyester with: a diameter of 0,1 mm or more but not more than 0,6 mm, a length of 30 mm or more but not more than 120 mm,

for use in the manufacture of paintbrushes 0 %-31.12.20260.3311ex5404909020Strip of polyimide0 %-31.12.2024 0.8382ex5407300010 Open mesh fabric made of thermally cross-bonded filaments of a polyolefin, with a density of 0,94 g/cm3 or more, with: a weight of 21 g/m2 or more but not more than 24 g/m2, a width of 560 mm or more but not more than 1200 mm, a thickness of 100 µm or more but not more than 120 µm, an elongation at break of not more than 20 % (ASTM D5034, machine direction), an elongation at break of not more than 22 % (ASTM D5034, cross direction), with a stretch of not more than 100 N /5 cm (ASTM D882, machine direction), and with a stretch of not more than 130 N /5 cm (ASTM D882, cross direction) 0 %-31.12.20270.3090 ex55031100 ex56013000 10 40 Synthetic staple fibres of a copolymer of terephthalic acid, p-phenylenediamine and 3,4’-oxybis(phenyleneamine), of a length of not more than 7 mm0 %-31.12.20240.3214 ex55039000 ex55069000 ex56013000 20 10 10 Poly(vinyl alcohol) fibres, whether or not acetalized0 %-31.12.20240.3212 ex56031110 ex56031190 ex56031210 ex56031290 ex56039110 ex56039190 ex56039210 ex56039290 10 10 10 10 10 10 10 10 Poly(vinyl alcohol) non-wovens, in the piece or cut into rectangles: of a thickness of 200 µm or more but not more than 280 µm and of a weight of 20 g/m2 or more but not more than 50 g/m2 0 %m231.12.20240.2552 ex56031290 ex56031390 ex56031480 ex56039290 ex56039390 ex56039480 30 30 10 60 40 30 Non-wovens of aromatic polyamide fibres obtained by polycondensation of m-phenylenediamine and isophthalic acid, in the piece or cut into rectangles0 %m231.12.2028 0.2548 ex56031290 ex56031390 60 60 Non-woven of spunbonded polyethylene, of a weight of more than 60 g/m2 but not more than 80 g/m2 and an air resistance (Gurley) of 8 seconds or more but not more than 36 seconds (as determined by the ISO 5636/5 method)0 %m231.12.20240.5059ex5603131020 Non-woven of spunbonded polyethylene, with a coating, of a weight of more than 80 g/m2 but not more than 105 g/m2 and an air resistance (Gurley) of 8 seconds or more but not more than 75 seconds (as determined by the ISO 5636/5 method) 0 %m231.12.20250.8024ex5603141030 Non-wovens, consisting of poly(ethylene terephthalate) spun bonded media: of weight of 160 g/m2 or more but not more than 300 g/m2, with a filtration efficiency of class M or better (according to DIN 60335-2-69), pleatable, with at least one of following treatments: a coating or covering with polytetrafluoroethylene (PTFE), a coating with aluminium particles, a coating of phosphorous based flame retardants, a nano fiber coating of a polyamide, a polyurethane or a fluorine-containing polymer 0 %m231.12.20240.5987ex5603148060 Non-wovens, consisting of poly(ethylene terephthalate) spun bonded media: of weight of 160 g/m2 or more but not more than 300 g/m2, with a filtration efficiency of class M or better (according to DIN 60335-2-69), pleatable, with or without an expanded polytetrafluoroethylene (ePTFE) membrane 0 %m231.12.20280.3041

ex56039290 ex56039390 20 20 Non-wovens consisting of a meltblown central layer of a thermoplastic elastomer laminated on each side with spunbonded filaments of polypropylene0 %m231.12.20240.3042 ex56039290 ex56039480 70 40 Non-wovens, consisting of multiple layers of a mixture of meltblown fibres and staple fibres of polypropylene and polyester, whether or not laminated on one side or on both sides with spunbonded filaments of polypropylene0 %m231.12.2028 0.5197 ex56039290 ex56039390 80 50 Non-woven polyolefin fabric, consisting of an elastomeric layer, laminated on each side with polyolefin filaments: a weight of 25 g/m2 or more but not more than 150 g/m2, in the piece or simply cut into squares or rectangles, not impregnated, with cross-directional or machine-directional stretch properties for use in the manufacture of infant/child care products 0 %m231.12.20260.6135ex5603939060 Nonwovens made of polyester fibres, with a weight of 85 g/m2, with a constant thickness of 95 µm (± 5 µm), neither coated nor covered, in 1 m wide rolls of 2000 m to 5000 m length, suitable for the coating of membranes in the manufacture of osmosis and reverse osmosis filters 0 %m231.12.20240.3210ex5603948020Acrylic fibre rods, having a length of not more than 50 cm, for the manufacture of pen tips0 %m231.12.20280.3406ex5607509010Unsterilised twine of poly(glycolic acid) or of poly(glycolic acid) and its copolymers with lactic acid, plaited or braided, with an inner core, for the manufacture of surgical sutures0 %-31.12.20240.2415ex5803001091Gauze of cotton, of a width of less than 1500 mm0 %-31.12.20240.7081ex5903209020 Two layers’ plastic-laminated textile fabric with: one layer consisting of knitted or crocheted polyester textile fabric, other layer consisting of polyurethane foam, a weight of 150 g/m2 or more, but not more than 500 g/m2, a thickness of 1 mm or more, but not more than 5 mm for use in the manufacture of the retractable roof of motor vehicles 0 %-31.12.20260.2417ex5906999010Rubberised textile fabric, consisting of warp yarns of polyamide–6,6 and weft yarns of polyamide–6,6, polyurethane and a copolymer of terephthalic acid, p-phenylenediamine and 3,4’-oxybis(phenyleneamine)0 %-31.12.2024 0.8213ex5906999030 Woven and coated rubberised textile fabric with the following characteristics: with three layers, the outer layers consist of a natural rubber, EPDM and chloropen rubber compound, the middle layer consists of polyester fabric, for use in the manufacture of life rafts 0 %-31.12.20260.2453ex5907000010Textile fabrics, coated with adhesive in which are embedded spheres of a diameter of not more than 150 µm0 %-31.12.20260.3207 ex59119099 ex84219990 30 92 Parts of equipment for the purification of water by reverse osmosis, consisting essentially of plastic-based membranes, supported internally by woven or non-woven textile materials which are wound round a perforated tube, and enclosed in a cylindrical plastic casing of a wall-thickness of not more than 4 mm, whether or not housed in a cylinder of a wall-thickness of 5 mm or more0 %-31.12.20240.4638ex5911909940Multi-layered non-woven polyester polishing pads, impregnated with polyurethane0 %-31.12.20240.7340ex5911909950Loudspeaker vibration damper, made from round, corrugated, flexible and cut-to-size tissue of textile fibres of polyester, cotton or aramid or a combination hereof, of a kind used in car loudspeakers0 %-31.12.20270.6469ex6804210020

Discs of synthetic diamonds which are agglomerated with a metal alloy, ceramic alloy or plastic alloy, having a self-sharpening effect by constant release of the diamonds, suitable for abrasive cutting of wafers, whether or not containing a hole in the centre, whether or not on a support with a weight of not more than 377 g per piece and with an external diameter of not more than 206 mm 0 %p/st31.12.20240.2755ex6813890020Friction material, of a thickness of less than 20 mm, not mounted, for use in the manufacture of friction components0 %-31.12.2024 0.5931ex6814100010Agglomerated mica with a thickness of not more than 0,15 mm, on rolls, whether or not calcined, whether or not reinforced with aramid fibres0 %-31.12.20240.2546ex6903909040Silicon carbide reactor tubes and holders having a maximum service temperature of 1370 °C or more0 %-31.12.20240.4978ex6909190020Silicon nitride (Si3N4) rollers or balls0 %-31.12.20250.6071ex6909190025Ceramic proppants, containing aluminium oxide, silicon oxide and iron oxide0 %-31.12.20240.3403ex6909190030Supports for catalysts, consisting of porous cordierite or mullite ceramic pieces, of an overall volume of not more than 65 l, having, per cm2 of the cross-section, not less than one continuous channel which may be open at both ends or stopped at one end0 %-31.12.20240.8028ex6909190040 Ceramic-carbon absorption or adsorption cartridges of fuel motor vehicle systems, with the following characteristics: extruded fired ceramic bound multicellular cylindrical structure, 5 % or more by weight but not more than 70 % by weight of activated carbon, 30 % or more by weight but no more than 90 % by weight of ceramic binder, with a diameter of 29 mm or more but no more than 41 mm, a length of not more than 150 mm, fired at temperature of 800 °C or more 0 %p/st31.12.20250.2538 ex69091900 ex69149000 50 20 Ceramic articles made of continuous filaments of ceramic oxides, containing by weight: 2 % or more of diboron trioxide, 28 % or less of silicon dioxide and 60 % or more of dialuminium trioxide 0 %-31.12.20240.3766ex6909190060Supports for catalysts, consisting of porous ceramic pieces, of a blend of silicon carbide and silicon, with a hardness of less than 9 on the Mohs scale, with a total volume of not more than 65 litres, having, per cm2 of the surface of the cross section one or more closed channels at the tail end0 %-31.12.2024 0.4582ex6909190070Supports for catalysts or filters, consisting of porous ceramics made primarily from oxides of aluminium and titanium; with a total volume of not more than 65 litres and at least one duct (open on one or both ends) per cm2 of cross section0 %-31.12.20240.3404ex6914900030Ceramic microspheres, transparent, obtained from silicon dioxide and zirconium dioxide, of a diameter of more than 125 µm0 %-31.12.20240.6286ex7006009025 Glass wafer made of borosilicate float glass with a total thickness variation of 1 µm or less, and laser-engraved 0 %p/st31.12.20240.7619ex7006009040 Plates of sodalime or borosilicate glass of STN (Super Twisted Nematic) or TN (Twisted Nematic) quality having:

a length of 300 mm or more but not more than 1500 mm, a width of 300 mm or more but not more than 1500 mm, a thickness of 0,5 mm or more but not more than 1,1 mm, an indium-tin-oxide coating with a resistance of 80 Ω or more, but not more than 160 Ω on one side, with or without a passivation layer of silicon dioxide (SiO2) between indium-tin-oxide layer and glass surface, with or without a multi layer anti-reflection-coating on the other side, and machined (chamfered) edges 0 %-31.12.20240.8265ex7007111010 Specifically shaped and toughened safety glass: with a width of 200 mm or more but not more than 600 mm, with a height of 150 mm or more but not more than 500 mm, for use in the manufacture of motor vehicle window assemblies 0 %-31.12.20260.6380ex7009100030 Layered glass with mechanical dimming ability by different angles of incident light comprising: whether or not a layer of chrome, a break-resistance adhesive tape or hot-melt adhesive, and a release film on the front side and protective paper at the back side, of a kind used for interior rear-view mirrors of vehicles 0 %p/st31.12.2024 0.5789ex7009100050 Unfinished electro-chromic auto-dimming mirror for motor vehicle rear-view mirrors: whether or not equipped with plastic backing plate, whether or not equipped with a heating element, whether or not equipped with Blind Spot Module (BSM) display 0 %-31.12.20270.6870ex7009100060 Electrochromic self-dimming inside rear-view mirror: with a mirror support in a plastic casing and with an integrated circuit, whether or not with a high beam assistant, whether or not with a digital compass, whether or not with a garage door opener, whether or not with an integrated toll module, whether or not with a camera for driver and/or cabin monitoring, whether or not with an infrared filter, for use in the manufacture of motor vehicles of Chapter 87 0 %-31.12.20250.3400ex7014000010Optical elements of glass (other than those of heading 7015), not optically worked, other than signalling glassware0 %-31.12.20240.3161 ex70191200 ex70191200 02 22 Rovings, measuring 650 tex or more but not more than 2500 tex, coated with a layer of polyurethane whether or not mixed with other materials0 %-31.12.20240.5750 ex70191200 ex70191200 05 25 Rovings ranging from 1980 to 2033 tex, composed of continuous glass filaments of 9 µm (± 0,5 µm)0 %-31.12.20270.2532ex7019130010Yarn of 33 tex or a multiple thereof (± 7,5 %), obtained from continuous spun-glass filaments of a nominal diameter of 3,5 µm or of 4,5 µm, in which filaments of a diameter of 3 µm or more but not more than 5,2 µm predominate, other than those treated so as to improve their adhesion to elastomers0 %-31.12.20240.5749ex7019130015S-glass yarn of 33 tex or a multiple of 33 tex (± 13 %) made from continuous spun-glass filaments with fibres of a diameter of 9 µm (- 1 µm / + 1,5 µm)0 %-31.12.2027 0.5021ex7019130020Yarn of 10,3 tex or more but not more than 11,9 tex, obtained from continuous spun-glass filaments, in which filaments of a diameter of 4,83 µm or more but not more than 5,83 µm predominate0 %-31.12.20250.5020ex7019130025Yarn of 5,1 tex or more but not more than 6,0 tex, obtained from continuous spun-glass filaments, in which filaments of a diameter of 4,83 µm or more but not more than 5,83 µm predominate0 %-31.12.20250.2535ex7019130030Yarn of E-glass of 22 tex (± 1,6 tex), obtained from continuous spun-glass filaments of a nominal diameter of 7 µm, in which filaments of a diameter of 6,35 µm or more but not more than 7,61 µm predominate0 %-31.12.20240.4848ex7019130050Yarn of 11 tex or a multiple thereof (± 7,5 %), obtained from continuous spun-glass filaments, containing 93 % by weight or more of silicon dioxide, of a nominal diameter of 6 µm or 9 µm, other than those treated0 %-31.12.20270.2872ex7019130055

Glass cord impregnated with rubber or plastic, obtained from K- or U-glass filaments, made up of: 9 % or more but not more than 16 % of magnesium oxide, 19 % or more but not more than 25 % of aluminium oxide, 0 % or more but not more than 2 % of boron oxide, without calcium oxide, coated with a latex comprising at least a resorcinol- formaldehyde resin and chlorosulphonated polyethylene 0 %-31.12.20240.7056 ex70196100 ex70196300 70 30 E-fibre glass fabrics: having a weight of 20 g/m2 or more, but not more than 214 g/m2, surface treated with an organosilane coupling agent, in rolls, having a humidity content by weight of 0,13 % or less, and having not more than 3 hollow fibres out of 100000 fibres, for the exclusive use in the manufacture of prepregs and copper clad laminates 0 %m231.12.2026 0.7647ex7019640040 Epoxy resin coated glass woven fabric containing by weight: 91 % or more but not more than 93 % of glass fibres, 7 % or more but not more than 9 % of epoxy resin 0 %-31.12.20240.4059 ex70197100 ex70197200 50 50 Non-woven product of non-textile glass fibre, for the manufacture of air filters or catalysts0 %-31.12.20260.3940ex7019809010Glass wool in which fibres of a diameter of less than 4,6 µm predominate0 %-31.12.20280.3153ex7019900020Glass cord impregnated with rubber or plastic, obtained from twisted glass filament yarns, coated with a latex comprising at least a resorcinol-formaldehyde-vinylpyridine resin and an acrylonitrile-butadiene rubber (NBR)0 %-31.12.20240.4024ex7019900030High modulus glass cord (K) impregnated with rubber, obtained from twisted high modulus glass filament yarns, coated with a latex comprising a resorcinol-formaldehyde resin with or without vinylpyridine and/or hydrogenated acrylonitrile-butadiene rubber (HNBR)0 %-31.12.20240.5348 ex70200010 ex76169990 10 77 Television pedestal stands with or without bracket for fixation to and stabilization of television cabinet case/body0 %p/st31.12.20260.7266ex7020001020 Raw material for optical elements of fused silicon dioxide with: a thickness of 10 cm or more but not more than 40 cm and a weight of 100 kg or more 0 %p/st31.12.20270.4127ex7201101110Pig iron ingots with a length of not more than 350 mm, a width of not more than 150 mm, a height of not more than 150 mm0 %-31.12.20260.4128ex7201103010Pig iron ingots with a length of not more than 350 mm, a width of not more than 150 mm, a height of not more than 150 mm, containing by weight not more than 1 % of silicon0 %-31.12.20260.335372025000Ferro-silico-chromium0 %-31.12.20240.4853ex7202998010 Ferro-dysprosium, containing by weight: 78 % or more of dysprosium, and 18 % or more but not more than 22 % of iron 0 %-31.12.2025 0.7502ex7318240040 Tube or pipe restraint joint elements: of stainless steel according to specification 17-4PH or of steel according to specification tool steel S7, produced by metal injection moulding, with a rockwell hardness of 38 HRC (± 1) or 53 HRC (+ 2/– 1), measuring 7 mm x 4 mm x 5 mm or more, but not more than 40 mm x 20 mm x 10 mm

0 %-31.12.20240.4548ex7320901091 Flat spiral spring of tempered steel, with: a thickness of 2,67 mm or more, but not more than 4,11 mm, a width of 12,57 mm or more, but not more than 16,01 mm, a torque of 18,05 Nm or more, but not more than 73,5 Nm an angle between the free position and the nominal position in exercise of 76° or more, but not more than 218° for use in the manufacture of tensioners for power transmission belts, for internal combustion engines 0 %p/st31.12.20240.4126ex7326200020Metal fleece, consisting of a mass of stainless steel wires of diameters of 0,001 mm or more but not more than 0,070 mm, compacted by sintering and rolling0 %-31.12.20260.7891ex7326909440Steel ball neck, drop forged, machined, also heat treated or surface treated, having an angle between the centre of the conical head and the arm of less than 90° or having an angle between the centre of the ball and the arm of less than 90°, for use in the manufacture of trailer hitches for passenger cars0 %-31.12.20240.6680 ex73269098 ex79070000 40 10 Iron, steel and/or zinc alloy weights: with a weight of not more than 500 grams and measuring not more than 107 mm x 107 mm x 11 mm, whether or not with parts of other material, whether or not with parts of other metals, whether or not surface treated, whether or not printed, of a kind used for the production of remote controls 0 %-31.12.2025 0.8480ex7326909860 Vane ring of a kind for fastening gas flow control blades: of iron or steel alloy, with a heat resistance of 830 °C or more but not more than 1050 °C, with an external diameter of not more than 92 mm, with holes for holding the gas flow control blades, for use in the manufacture of turbochargers 0 %-31.12.20270.8512ex7326909870 Disc of a kind for ensuring the gas flow channel width: of iron or steel alloy, with a heat resistance of 830 °C or more but not more than 1050 °C, with an external diameter of not more than 92,5 mm, with an internal diameter of not more than 62 mm, for use in the manufacture of turbochargers 0 %-31.12.20270.3352ex7410210010Sheet or plate of polytetrafluoroethylene, containing aluminium oxide or titanium dioxide as filler or reinforced with glass-fibre fabric, covered on both sides with copper foil0 %-31.12.20240.7509ex7410210020Foils, rolls composed of one layer of glass epoxy of 100 µm colaminated with refined copper foil on one or two sides of 35 µm with a tolerance of 10 % for use in the production of smart cards0 %m231.12.20240.3005ex7410210030Film of polyimide, whether or not containing epoxide resin and/or glass fibre, covered on one side or on both sides with a copper foil0 %-31.12.20240.3926ex7410210040 Sheet or plates: consisting of at least a central layer of paper or one central sheet of any type of nonwoven fibre, laminated on each side with glass-fibre fabric and impregnated with epoxide resin, or consisting of multiple layers of paper, impregnated with phenolic resin, coated on one or both sides with a copper film with a maximum thickness of 0,15 mm

0 %-31.12.2024 0.4479ex7410210050 Plates: consisting of at least one layer of fibreglass fabric impregnated with thermosetting resin, covered on one or both sides with copper foil with a thickness of not more than 0,15 mm, and with a dielectric constant (DK) of less than 3,9 and a loss factor (Df) of less than 0,015 at a measuring frequency of 10 GHz, as measured according to IPC-TM-650 0 %-31.12.20240.7341ex7413000020Loudspeaker centring ring, consisting of one or more vibration dampers and minimum two non-insulated copper cables, therein woven or pressed0 %-31.12.20270.2447 ex74198090 ex76169990 91 60 Disc (target) with deposition material, consisting of molybdenum silicide: containing 1mg/kg or less of sodium and mounted on a copper or aluminium support 0 %-31.12.20240.7911ex7506200010 Sheets and strips in coils of nickel alloy C276 (EN 2.4819) with a thickness of 0,5 mm or more but not more than 3 mm, a width of 770 mm or more but not more than 1250 mm 0 %-31.12.20240.7913ex7506200020 Sheets and strips in coils of nickel alloy to standard ASME SB-582/UNS N06030 with: a thickness of 0,5 mm or more but not more than 3 mm, a width of 250 mm or more but not more than 1219 mm 0 %-31.12.20250.5890 76012030 76012040 Slabs and billets of unwrought aluminium alloys4 %-31.12.20240.7752ex7604210010 Hollow profile with: one closed chamber of aluminum alloy 6063-T5 or 6060-T5, a wall thickness of not more than 0,7 mm, and an anodized layer of 10 µm at the surface, for use in the manufacture of board frames of whiteboards, cork boards, easel boards, education boards and display cases 0 %-31.12.2024 0.5029 ex76042910 ex76061299 ex76061299 10 21 25 Sheets and bars of aluminium-lithium alloys0 %-31.12.20270.6417ex7604291040 Bars and rods of aluminium alloys containing by weight: 0,25 % or more but not more than 7 % of zinc, and 1 % or more but not more than 3 % of magnesium, and 1 % or more but not more than 5 % of copper, and not more than 1 % of manganese consistent with the material specifications AMS QQ-A-225, of a kind used in aerospace industry (inter alia conforming NADCAP and AS9100) and obtained by rolling mill process 0 %-31.12.20240.2410ex7605190010Not alloyed aluminium wire, of a diameter of 2 mm or more but not more than 6 mm, covered with a layer of copper of a thickness of 0,032 mm or more but not more than 0,117 mm0 %-31.12.20240.8344ex7605210010Aluminium alloy wire with a diameter of 9,50 mm or more but not more than 19,15 mm, in coils, for use in the manufacture of aeronautical fasteners0 %-31.12.20270.6418ex7605290010 Wire of aluminium alloys containing by weight: 0,10 % or more but not more than 5 % of copper, and 0,2 % or more but not more than 6 % of magnesium, and 0,10 % or more but not more than 7 % of zinc, and not more than 1 % of manganese, consistent with the material specifications AMS QQ-A-430, of a kind used in aerospace industry (inter alia conforming NADCAP and AS9100) and obtained by rolling mill process 0 %m31.12.20240.7698ex7607209910

Aluminium foil, in rolls: coated on one side with polypropylene or polypropylene and acid-modified polypropylene and on the other with polyamide and polyethylene terephthalate, with adhesive layers between them, with a width of 200 mm or more, but not more than 400 mm, with a thickness of 0,138 mm or more, but not more than 0,168 mm, for use in the manufacture of lithium-ion battery cell covers 3,7 %-31.12.2024 0.7746ex7608208120 Seamless aluminium alloyed extruded tubes (Aluminum 6061F according to standard ASTM B241) with: an outer diameter of 320 mm or more but not more than 400 mm, and a wall thickness of 8 mm or more but not more than 10 mm, for use in the manufacture of high pressure vessels 0 %-31.12.20240.6138ex7608208930 Seamless aluminium alloyed extruded tubes with: an outer diameter of 60 mm or more but not more than 420 mm, and a wall thickness of 10 mm or more but not more than 80 mm 0 %-31.12.20240.7747ex7608208940 Seamless flow forming aluminium alloyed tubes (Aluminum 6061A according to standard ISO 7866) with: an outer diameter of 378 mm or more but not more than 385 mm, and a wall thickness of 4 mm or more but not more than 7 mm for use in the manufacture of high pressure vessels 0 %-31.12.20240.8194 ex76090000 ex84159000 30 45 Aluminium connecting block for automotive air conditioning systems: with a T6 hardening, equipped with round stubs with a circumferential outer groove, with through or non-through holes, made of profiles with an upper radius of 8 mm or more but not more than 11 mm, and a lower radius of 12 mm or more but not more than 17 mm, with a distance between holes of 15 mm or more but not more than 22 mm, with sockets designed for brazing or clamping, with mounting holes for M6 or M8 mounting screw, threaded or not, with a width of 5 mm or more but not more than 16 mm, for connecting a compressor, a condenser, an evaporator, a chiller and other lines 0 %-31.12.2026 0.8464ex7609000040 Flame brazed aluminium block for connecting tubes in automotive heat exchangers and/or turbocharged air coolers and/or automatic transmission coolers: with extruded, bent connection tubes with an outer diameter of 5 mm or more, but not more than 25 mm, with a weight of 0,02 kg or more, but not more than 0,25 kg, for use in the manufacture of cooling system in vehicles of Chapter 87 0 %p/st31.12.20270.8503ex7609000050 Machined aluminium components: containing by weight 0,55 %, or more but not more than 0,61 % of magnesium, containing by weight 0,55 %, or more but not more than 0,61 % of silicon, with a hardening state of T5 or T6, with a mass of 0,05 kg or more, but not more than 0,2 kg, for use in the manufacture of CO2 cooling systems in motor vehicles 0 %p/st31.12.20270.8493ex7609000060 Aluminium connection block: with a weight of 3 g or more but not more than 400 g, manufactured from 6061-T6 or 6060-T6 or 6082-T6 aluminium grade, being an integral part of an air conditioning hose assembly or oil cooling line hose assembly or air brake line hose assembly or water cooling line hose assembly,

with holes (sockets) or splines (pilots) or threads that allow installation in an automotive or other air conditioning system (also understood as installation in the line), with sockets designed for brazing or fastening, with at least 1 through-hole with a diameter of 3 mm or more but not more than 25 mm, for the manufacture of automotive cooling and air conditioning systems 0 %p/st31.12.20270.2445ex7613000020Aluminium container, seamless, for compressed natural gas or compressed hydrogen, wholly embedded in an overwrap of epoxy-carbon fibres composite, of a storage capacity of 172 l (± 10 %) and an unfilled weight of not more than 64 kg0 %p/st31.12.2024 0.3928ex7616999015Honeycomb aluminium blocks for use in the manufacture of aircraft parts0 %p/st31.12.20240.6534ex7616999025 Metallised film: consisting of eight or more layers of aluminium (CAS RN 7429-90-5) of a purity of 99,8 % or more, with an optical density of each aluminium layer of not more than 3.0, with each aluminium layer separated by a resin layer, on a carrier film of PET, and on rolls of up to 50000 metres in length 0 %-31.12.20240.5357 ex76169990 ex84828000 ex88073000 70 10 40 Connecting components for use in the production of helicopter tail rotor shafts0 %p/st31.12.20260.6730ex8101960010 Tungsten wire containing by weight 99 % or more of tungsten with: a maximum cross-sectional dimension of not more than 50 µm a resistance of 40 Ω or more but not more than 300 Ω at length of 1 metre 0 %-31.12.20250.7245ex8101960020 Tungsten wire containing by weight 99,95 % or more of tungsten, and with a maximum cross-sectional dimension of not more than 1,02 mm 0 %-31.12.20270.5694ex8102100010 Molybdenum powder with: a purity by weight of 99 % or more and a particle size of 1,0 µm or more, but not more than 5,0 µm 0 %-31.12.20270.5097ex8104300035 Magnesium powder: of purity by weight of more than 99,5 %, and with a particle size of not more than 0,8 mm 0 %-31.12.20250.3417ex8104900010Ground and polished magnesium sheets, of dimensions not more than 1500 mm × 2000 mm, coated on one side with an epoxy resin insensitive to light0 %-31.12.2024 0.5838ex8105900010 Bars or wires made of cobalt alloy containing, by weight: 35 % (± 2 %) cobalt, 25 % (± 1 %) nickel, 19 % (± 1 %) chromium and 7 % (± 2 %) iron, conforming to the material specifications AMS 5842 0 %-31.12.20240.3416ex8108200010Titanium sponge0 %-31.12.20240.4553ex8108200030Titanium powder of which 90 % by weight or more passes through a sieve with an aperture of 0,224 mm0 %-31.12.20240.3211ex8108300010Waste and scrap of titanium and titanium alloys, except those containing by weight 1 % or more but not more than 2 % of aluminium0 %-31.12.20240.4363ex8108903010Titanium alloy rods complying with standard EN 2002-1, EN 4267 or DIN 650400 %-31.12.20240.7330ex8108903015 Rods and wire of an alloy of titanium with: a uniform solid cross-section in the form of a cylinder, with a diameter of 0,8 mm or more, but not more than 5 mm, an aluminium content by weight of 0,3 % or more, but not more than 0,7 %,

a silicon content by weight of 0,3 % or more, but not more than 0,6 %, a niobium content by weight of 0,1 or more, but not more than 0,3 %, and an iron content by weight of not more than 0,2 % 0 %-31.12.20270.7942ex8108903035Bars and wires of titanium with a titanium content of 98,8 % or more but not more than 99,9 % of a diameter less than 20 mm0 %-31.12.20250.4904ex8108903045Titanium-aluminium-vanadium alloy (TiAl6V4) wire, of a diameter less than 20 mm and complying with AMS standards 4928, 4965 or 49670 %-31.12.2025 0.8105ex8108903055 Wires of an alloy of titanium: with a niobium content by weight of 42 % or more, but not more than 47 %, with a diameter of 2,36 mm or more, but not more than 7,85 mm, in coils of 15 kg or more, but not more than 45 kg, complying with standard AMS 4982 0 %-31.12.20250.7077ex8108903060 Forged cylindrical bars of titanium with: a purity of 99,995 % by weight or more, a diameter of 140 mm or more but not more than 200 mm, a weight of 5 kg or more but not more than 300 kg 0 %p/st31.12.20260.5351ex8108903070 Wire of an titanium alloy containing by weight: 22 % (± 1 %) of vanadium, and 4 % (± 0,5 %) of aluminium or 15 % (± 1 %) of vanadium, 3 % (± 0,5 %) of chromium, 3 % (± 0,5 % of tin and 3 % (± 0,5 %) of aluminium 0 %-31.12.20260.7285ex8108905045 Cold or hot rolled plates, sheets and strips of non-alloyed titanium with: a thickness of 0,4 mm or more, but not more than 100 mm, a length of not more than 14 m, and a width of not more than 4 m 0 %-31.12.20270.5352ex8108905055Plates, sheets, strip and foil of an alloy of titanium0 %-31.12.20260.6524ex8108905080 Plates, sheets, strips and foil of non-alloyed titanium of a width of more than 750 mm, of a thickness of not morethan 3 mm 0 %-31.12.20240.6500ex8108905085 Strip or foil of non-alloyed titanium: containing more than 0,07 % by weight of oxygen (O2), of a thickness of 0,4 mm or more but not more than 2,5 mm conforming to the Vickers hardness HV1 standard of not more than 170 of a kind used in the manufacture of welded tubes for nuclear power plant condensers 0 %-31.12.2024 0.5353 ex81089090 ex90039000 30 20 Parts of spectacle frames and mountings, including temples, blanks of a kind used for the manufacture of spectacle parts and bolts of the kind used for spectacle frames and mountings, of a titanium alloy 0 %p/st31.12.20260.2515 ex81092100 ex81092900 10 10 Non-alloy zirconium sponges or ingots, containing by weight more than 0,01 % of hafnium for use in the manufacture of tubes, bars or ingots enlarged by remelting for the chemical industry0 %-31.12.20240.3415ex8110100010Antimony in the form of ingots0 %-31.12.20240.3413ex8112995010Alloy of niobium (columbium) and titanium, in the form of bars and rods0 %-31.12.20240.5354ex8113002010Cermet blocks containing by weight 60 % or more of aluminium and 5 % or more of boron carbide0 %-31.12.20240.4316ex8113009010Carrier plate of aluminium silicon carbide (AlSiC-9) for electronic circuits0 %-31.12.20270.6805ex8113009020Cuboid spacer made of aluminium silicon carbide (AlSiC) composite used for packaging in IGBT-modules0 %-31.12.20250.6416ex8207191010Inserts for drilling tools with working parts of agglomerated diamonds0 %p/st31.12.20240.5570ex8207301010Set of transfer and/or tandem press tools for cold-forming, pressing, drawing, cutting, punching, bending, calibrating, bordering and throating of metal sheets, for use in the manufacture of frame parts or body parts of motor vehicles0 %p/st31.12.20270.7693ex8301200010

Mechanical or electromechanical steering column lock: with a height of 10,5 cm (± 3 cm), with a width of 6,5 cm (± 3 cm), in a metal housing, whether or not with a holder, for use in the manufacture of goods of Chapter 87 0 %-31.12.2024 0.5024 ex83016000 ex84199085 ex84799070 ex84819000 ex84859090 ex85030099 ex85159080 ex85371098 ex85389099 ex87089910 ex87089997 30 40 30 50 30 43 40 55 70 55 22 Silicone or plastic keyboards, comprising: parts of common metal, and whether or not comprising parts of plastic, epoxy resin reinforced with fiberglass or wood, whether or not printed or surface-treated, with or without electrical conductors, with or without a membrane bonded to the keyboard, with or without mono or multilayer protective film 0 %p/st31.12.20250.8247ex8302100020 Armrest hinge made of magnesium with: a length of 239 mm or more but not more than 270 mm, a width of 150 mm or more but not more than 175 mm, a height of 110 mm or more but not more than 135 mm, mounting holes for a lock mechanism 0 %-31.12.20260.7666ex8302300010 Support bracket for an exhaust system: with a thickness of 0,7 mm or more but not more than 1,3 mm, of stainless steel class 1.4310 and 1.4301 according to norm EN 10088, whether or not with mounting holes, for use in the manufacture of exhaust systems for automobiles 0 %-31.12.20240.8304ex8302300020 Two cold-formed steel supports: with a length of 120 mm or more but not more than 180 mm, with a width of 50 mm or more but not more than 80 mm, with a height of 35 mm or more but not more than 80 mm, with a movable riveted connection, with or without elastomeric bumper, forming a mechanism for indirect movement of the mechanism of the longitudinal positioner of car seats, interacting with the safety latch, attached to the mechanism of the longitudinal positioner by means of a detachable screw connection, riveting, welding or spot welding 0 %-31.12.2026 0.2602ex8309909010 Aluminium can ends: with a diameter of 99,00 mm or more but not more than 136,5 mm (±1mm), whether or not with a ring-pull aperture 0 %p/st31.12.20240.3947ex8401300020Non-irradiated hexagonal fuel modules (elements) for use in nuclear reactors0 %-31.12.20240.6319ex8401400010Stainless steel absorber control rods, filled with neutron absorbing chemical elements0 %p/st31.12.20240.8012ex8406820010 Industrial steam turbine with: an output of 5 MW or more but not more than 40 MW, designed for a pressure of not more than 140 bar and a temperature of not more than 540 °C, equipped with double seat valves on the live steam side which are operated with a hydraulic servo of not more than 12 bar 0 %-31.12.20250.3830 ex84073320 ex84073380 ex84079080 ex84079090 10 10 10 10 Spark-ignition reciprocating or rotary internal combustion piston engines, having a cylinder capacity of not less than 300 cm3 and a power of not less than 6 kW or more but not more than 20,0 kW, for the manufacture of: lawn mowers of subheadings 843311, 843319 and 843320, tractors of subheadings 87019190, 87019290 whose main function is that of a lawn mower,

four stroke mowers with motor of a cylinder capacity of not less than 300 cm3 of subheading 84332010 or snowploughs and snow blowers of subheading 843020 0 %-31.12.20270.8260ex8407341010 Spark-ignition reciprocating or rotary internal combustion piston engines, with: a cylinder capacity of 1200 cm3 or more but not more than 2000 cm3 a power of 95 kW but not more than 135 kW, a weight of not more than 120 kg, for use in the manufacture of motor vehicles of heading 8703 0 %-31.12.2026 0.3828ex8407901010Four-stroke petrol engines of a cylinder capacity of not more than 250 cm3 for use in the manufacture of garden equipment of heading 8432, 8433, 8436 or 85080 %-31.12.20260.8403ex8407901040 A power unit with a two-stroke engine with: an output of 900 W or more, but not more than 1100 W, a cylinder displacement of more than 24 cm3 but not more than 30 cm3, a rotation speed of more than 8400 rpm but not more than 8600 rpm at maximum power, an idling speed of more than 2800 rpm but not more than 3200 rpm, and a fuel tank with a capacity of 0,5 l or more, for use in the manufacture of garden machinery and garden machinery components 0 %-31.12.20270.4996ex8407909020 Compact Liquid Petroleum Gas (LPG) Engine System, with: 6 cylinders, an output of 75 kW or more, but not more than 80 kW, inlet and exhaust valves modified to operate continuously in heavy duty applications, for use in the manufacture of vehicles of heading 8427 0 %-31.12.20250.2598ex8408904120Diesel engines of a power of not more than 15 kW, with 2 or 3 cylinders, for use in the manufacture of vehicle mounted temperature control systems0 %-31.12.20240.2595ex8408904320Diesel engines of a power of not more than 30 kW, with 4 cylinders, for use in the manufacture of vehicle mounted temperature control systems0 %-31.12.20240.5544 ex84089043 ex84089045 ex84089047 40 30 50 4 Cylinder, 4 cycle, liquid cooled, compression-ignition engine having: a capacity of not more than 3850 cm3, and a rated output of 15 kW or more but not more than 85 kW, for use in the manufacture of vehicles of heading 8427 0 %-31.12.2024 0.8300 ex84089065 ex84089067 ex84089081 20 20 20 Compression-ignition internal combustion piston engines: of the inline type, with a cylinder capacity of 7000 cm3 or more but not more than 18100 cm3, with a power of 205 kW or more but not more than 597 kW, with an exhaust after-treatment module, with external width/height/depth dimensions of not more than 1310/ 1300/1040 mm or 2005/1505/1300 mm or 2005/1505/1800 mm, for use in the manufacture of crushing, screening, separation or compost turning machines 0 %-31.12.20260.7670ex8409910025 Air intake module for engine cylinders consisting of: a suction pipe, a pressure sensor, an electric throttle, hoses, brackets, for use in the manufacture of engines of motor vehicles 0 %-31.12.20240.8466ex8409910033 Camshaft carrier for a spark-ignition piston internal combustion engine, made of ADC12 aluminium alloy, with: a weight of 4,0 kg or more but not more than 5,5 kg,

a wall thickness of 2,0 mm or more but not more than 6,0 mm, for use in the manufacture of motor vehicle engines 0 %p/st31.12.20270.8216ex8409910035 Fuel distribution pipe complete consisting of rail pipe, high pressure sensor and injectors for direct gasoline fuel injection with: an operating pressure of not more than 22,5 MPa, solenoid direct injector, analog pressure sensor for not more than 22,5 MPa 0 %-31.12.20260.8469ex8409910038Crankcase for 4-cylinder spark-ignition piston internal combustion engine, made of ADC12 aluminium alloy, for use in the manufacture of motor vehicle engines0 %-31.12.2027 0.7027ex8409910040Fuel injector with solenoid valve for optimized atomization in the combustion chamber for use in the manufacture of spark-ignition internal combustion piston engines of motor vehicles0 %-31.12.20260.7234 ex84099100 ex84099900 45 70 Metal alloy intake and exhaust valve, with a Rockwell hardness HRC 20 or more, for use in the manufacture of spark or compression ignition engines of motor vehicles0 %-31.12.20260.6752 ex84099100 ex84099900 50 55 Exhaust manifold with turbine housing of turbochargers, with a hole to insert a turbine wheel, whereby the hole has a diameter of 28 mm or more, but not more than 181 mm0 %p/st31.12.20240.7667 ex84099100 ex84099900 53 65 The exhaust gas recirculation assembly consisting of: a control unit, an air throttle, an intake pipe, an outlet hose, for use in the manufacture of spark-ignition or compression-ignition combustion engines of motor vehicles 0 %-31.12.20240.7961 ex84099100 ex84819000 55 60 Nozzle body for the regulation of angle and distribution of fuel injection: of a cylindrical shape, made of stainless steel, with 4 or more, but not more than 16 holes, with a flow rate of 100 cm3/minute or more, but not more than 500 cm3/minute 0 %-31.12.20250.7661ex8409910070 Inlet manifold, exclusively for use in the manufacture of the motor vehicles with: a width of 40 mm or more but not more than 70 mm, valves length of 250 mm or more but not more than 350 mm, air volume of 5,2 litres, and an electrical flow control system that provides maximum performance at more than 3200 rpm 0 %-31.12.2024 0.7965ex8409910075 Housing of fuel injection valve for generating an electromagnetic field to actuate the injection valve with: an inlet diameter of 2 mm or more, but not more than 10 mm, an outlet diameter of 2 mm or more, but not more than 10 mm, an electric coil with a resistance of 10 Ω or more, but not more than 15 Ω, which ends in an electrical connection, a plastic covering moulded around a stainless steel tube 0 %-31.12.20250.7967 ex84099100 ex84819000 80 70 Nozzle needle for opening and closing the flow of fuel in the engine, with: 2 holes, 4 grooves, a diameter of 3 mm or more, but not more than 6 mm, a length of 25 mm or more, but not more than 35 mm, made of stainless steel with hard-chrome plating 0 %-31.12.20250.8244ex8409910085 Cylinder head blank for a four cylinder engine with 10 cores, made of aluminium alloy EN AC-45500, with:

no other components, a hardness of 52 HRB or more, casting defects size of not more than 0,4 mm and not more than 10 defects per cm2, a dendrite arm space in combustion chamber of not more than 25 µm, a double deck water jacket design and a weight of 18 kg or more but not more than 19 kg, a length of 506 mm or more but not more than 510 mm, a height of 282 mm or more but not more than 286 mm, a width of 143,7 mm or more but not more than 144,3 mm, in one single consignment of 1000 pieces or more 0 %p/st31.12.20260.5199 ex84099900 ex84799070 10 85 Injectors with solenoid valve for optimised atomisation in the engine combustion chamber0 %p/st31.12.2026 0.7851ex8409990025 Hoses assembly for fuel return from injectors to engine fuel unit consisting of at least: three rubber hoses, whether or not with a protective braided sleeving, three connectors for connecting fuel injectors, five metal clamps, one T-shaped plastic joint, for use in the manufacture of engines of motor vehicles 0 %-31.12.20240.7718ex8409990075 High pressure fuel rail of galvanised ferrite-pearlite steel with: at least one pressure sensor and one valve, a length of 314 mm or more but not more than 322 mm, an operating pressure not more than 225 MPa, an inlet temperature not more than 95°C, ambient temperature of -45°C or more but not more than 145°C, for use in the manufacture of compression ignition engines of motor vehicles 0 %-31.12.20240.6751ex8411990020 Wheel-shaped gas turbine component with blades, of a kind used in turbochargers: of a precision-cast nickel based alloy complying with standard DIN G- NiCr13Al6MoNb or DIN G- NiCr13Al16MoNb or DIN G- NiCo10W10Cr9AlTi or DIN G- NiCr12Al6MoNb or AMS AISI:686, with a heat-resistance of not more than 1100 °C, with a diameter of 28 mm or more, but not more than 180 mm, with a height of 20 mm or more, but not more than 150 mm 0 %p/st31.12.20270.7225ex8411990030Turbine housing of turbochargers, with a hole to insert a turbine wheel, whereby the hole has a diameter of 28 mm or more, but not more than 181 mm0 %p/st31.12.2026 0.5975ex8412390020 Actuator for a single-stage turbocharger, with: a pressure inlet pipe and a control rod with a working stroke of 15 mm or more but not more than 40 mm, a maximum length of the actuator including control rod of not more than 400 mm, a maximum diameter of the can at the widest point of not more than 140 mm, and a maximum height of the can without control rod of not more than 140 mm 0 %p/st31.12.20240.8148ex8412908020 Bedplate made of solution strengthened ductile iron castings (SSDI), for anchoring and aligning the drive train (gearbox, pedestal bearing, rotor shaft) of a wind turbine with: a length of 3,5 m or more but not more than 4,5 m, a width of 2 m or more but not more than 4,2 m, a height of 1 m or more, but not more than 1,3 m, a weight of 11 tons or more but not more than 21,5 tons, mounting bores for yawdrive, a mounting flange for gearbox support, drivetrain mount, different screw sockets 0 %p/st31.12.20270.8079ex8412908030

Gearbox support used as a support and load-carrying component between the gearbox and the bedplate of a wind turbine, made of solution strengthened ductile iron castings (SSDI), with: a diameter of 2 m or more, but not more than 5 m, a weight of 2 tons or more but not more than 7 tons 0 %p/st31.12.20250.7161ex8413302030 Single-cylinder radial-piston high pressure pump for gasoline direct injection with: an operating pressure of 200 bar or more, but not more than 350 bar, a flow control, and a pressure relief valve, for use in the manufacture of engines of motor vehicles 0 %-31.12.2026 0.7969ex8413302040 High-pressure plunger pump for direct diesel injection, with: an operating pressure of not more than 275 MPa, a camshaft, a fluid discharging of 15 cm3 per minute or more, but not more than 1800 cm3 per minute, an electric pressure regulating valve 0 %-31.12.20250.7970ex8413302050 High-pressure plunger pump for direct diesel injection: with an operating pressure of not more than 275 MPa, designed to contact the crankshaft, with an electromagnetic valve 0 %-31.12.20250.8215ex8413302060 High-pressure plunger pump for direct petrol injection: with an operating pressure of not more than 90 MPa, designed to contact the crankshaft, with an electromagnetic valve 0 %-31.12.20260.8332ex8413308020 Electric water pump ensuring the functionality of the water circuit also when the motor is temporarily switched off, for operating DC voltage of 9 V or more but not more than 16 V, with: capacity - pressure 0,075 MPa at 3800 rpm, discharge of 12 l/min, whether or not with connecting cable with connector, and mounting bracket, for use in the manufacture of goods of Chapter 87 0 %-31.12.20270.8185ex8413705120 Electric brushless direct current motor with single-stage, radial flow pump centrifugal single entry impeller mounted on motor’s shaft and volute with integrated heater of nominal power of 1800 W and soldered safety devices, monobloc with the motor, with: a discharge outlet diameter of 20 mm or more, 9 slots stator, 6 pole rotor, rated power of 95 W, volute with straight outlet, rotor chamber without sand filter 0 %-31.12.2026 0.8186ex8413705130 Electric brushless direct current motor with single-stage, radial flow pump centrifugal single entry impeller mounted on motor’s shaft and volute with integrated heater of nominal power of 1800 W and soldered safety devices, monobloc with the motor, with: a discharge outlet diameter of 20 mm or more, 9 slots stator, 6 pole rotor, rated power of 95 W, volute with clamped rubber hose outlet, rotor chamber without sand filter 0 %-31.12.20260.8187ex8413705140 Electric brushless direct current motor with single-stage, radial flow pump centrifugal single entry impeller mounted on motor’s shaft, monobloc with the motor, volute with integrated heater, with: a discharge outlet diameter of 20 mm or more, 9 slots square or chain pole stator, 6 pole rotor, ferritic or rare earth magnets, rated power of 95 W or 80 W, heater of nominal power of 1800 W and soldered or laser welded safety, devices,

volute with or without clamped rubber outlet, rotor chamber with ultrasonic welded sand filter 0 %-31.12.20260.6346ex8413910030 Fuel pump cover: consisting of aluminium alloys, with a diameter of 38 mm or 50 mm, with two concentric, annular grooves formed on its surface, anodized, of a kind used in motor vehicles with petrol engines 0 %p/st31.12.20240.7669ex8414102530 Tandem pump consisting of: an oil pump with displacement of 21,6 cc/rev (± 2 cc/rev) and working pressure 1,5 bar at 1000 revolutions per minute, vacuum pump with displacement of 120 cc/rev (± 12 cc/rev) and performance of -666 mbar in 6 seconds at 750 revolutions per minute for use in the manufacture of engines of motor vehicles 0 %-31.12.2024 0.7691ex8414108930 Electric vacuum pump with: Controller Area Network (CAN bus), whether or not with a rubber hose, a connecting cable with connector, a mounting bracket, for use in the manufacture of goods of Chapter 87 0 %-31.12.20240.4727ex8414308150Hermetic or semi-hermetic variable-speed electric scroll compressors, with a nominal power rating of 0,5 kW or more but not more than 10 kW, with a displacement volume of not more than 35 cm3, of the type used in refrigeration equipment0 %-31.12.20240.6160 ex84143081 ex84148073 60 30 Hermetic rotary compressors for either hydrofluorocarbon (HFC) or hydrocarbon refrigerants: driven by on-off single phase alternate current (AC) or brushless direct current (BLDC) variable speed motors, with a nominal power rating of not more than 1,5 kW, a rated voltage of 100 V or more but not more than 240 V, with a height of not more than 300 mm, an external diameter of not more than 150 mm, with a unit weight of not more than 15 kg, for use in the manufacture of heat pumps for household appliances, including clothes dryers 0 %-31.12.20240.2593ex8414308920Vehicle air conditioning system part, consisting of an open shaft reciprocating compressor of a power of more than 0,4 kW but not more than 10 kW0 %-31.12.20240.7694ex8414308930Open shaft, scroll type compressor with clutch assembly, of a power of more than 0,4 kW, for air conditioning in vehicles, for use in the manufacture of motor vehicles of Chapter 870 %-31.12.2024 0.7595ex8414593520 Radial fan, with: a dimension of 25mm (height) x 85mm (width) x 85mm (depth), a weight of 120 g, a rated voltage of 13,6 VDC (direct current voltage), an operating voltage of 9 VDC or more but not more than 16 VDC (direct current voltage), a rated current of 1,1 A (TYP), a rated power of 15 W, a rotation speed of 500 RPM (revolutions per minute) or more but not more than 4800 RPM (revolutions per minute) (free flow), an air flow of not more than 17,5 litre/s, an air pressure of not more than16 mm H2O ≈ 157 Pa, an overall sound pressure of not more than 58 dB(A) at 4800 RPM (revolutions per minute), and with a FIN (Fan Interconnect Network) interface for communication with the heating and air-conditioning control unit used in car seat ventilation systems 0 %-31.12.20240.8207ex8414593530

Electric blower for cooling the high-voltage battery of a hybrid passenger car with: a control unit, MOSFET inverter, a voltage of 9 V or more but not more than 16 V, ambient temperature of – 40 °C or more, but not more than 80 °C, for use in the manufacture of hybrid passenger cars 0 %-31.12.20260.7317ex8414802220 Air membrane compressor with: a flow of 4,5 l/min or more, but not more than 12 l/min, power input of not more than 14 W, and a gauge pressure capacity not exceeding 400 hPa (0,4 bar), of a kind used in the production of motor vehicle seats 0 %-31.12.2027 0.8133ex8414807350 Hermetic heat pump compressor, for R134A or R450A as refrigerant: not charged with refrigerant, pre-charged with the lubricant oil, with the Single Phase Induction Motor PSC (Permanent Split Capacitor), having bottom side suction connection and top side discharge connection, with displacement 8,05 cm3 or higher, but not higher than 8,25 cm3, running at 2800 rpm or faster, but not faster than 3100 rpm, and with a cooling capacity of 920 W or higher, but not higher than 990 W in ASHRAE conditions 0 %-31.12.20250.8483ex8414900015 Fan assembly made of aluminium and magnesium alloy: with an outer diameter of 54 mm or more but not more than 130 mm, with a height of 8 mm or more but not more than 30 mm, with two discs connected by blades of involute shape, with or without dowel, and with or without washer, for use in the manufacture of electromotors 0 %-31.12.20270.2507ex8414900020Aluminium pistons, for incorporation into compressors of air conditioning machines of motor vehicles0 %p/st31.12.20240.8494ex8414900025 Scroll type compressor housing of an aluminium alloy of a kind with: a heat resistance of 200 °C or more but not more than 250 °C, one or more fixing points suitable for mounting an actuator, for use in the manufacture of turbochargers 0 %-31.12.20270.3386ex8414900030Pressure-regulating system, for incorporation into compressors of air conditioning machines of motor vehicles0 %p/st31.12.20240.4027ex8414900040Drive part, for compressors of air conditioning machines of motor vehicles0 %p/st31.12.2024 0.8465ex8415900015 Electrically welded manifolds for the condenser in automotive air conditioning systems: consisting of a tube produced by stamping an aluminium strip and joining the edges by electric arc welding, containing internal baffles responsible for the proper flow of coolant, with a length of 190 mm or more, but not more than 460 mm, with a diameter of 9 mm or more, but not more than 42 mm, with a weight of 0,01 kg or more, but not more than 0,45 kg, whether or not having aluminium connection blocks, used in the production of air conditioning systems in vehicles of Chapter 87 0 %p/st31.12.20270.6842ex8415900060 Flame-soldered aluminium block, for connecting tube with condenser in car air-conditioning systems, with: extruded, bent connector lines of aluminium with an external diameter of 5 mm or more, but not more than 25 mm, a weight of 0,02 kg or more but not more than 0,25 kg

0 %p/st31.12.20250.6860ex8415900065 Aluminium arc-welded removable receiver dryer, with polyamide and ceramic elements with: a length of 143 mm or more but not more than 292 mm, a diameter of 31 mm or more but not more than 99 mm, with a weight of not less than 0,12 kg and not more than 0,9 kg, a spangle length of not more than 0,2 mm and a thickness of not more than 0,06 mm, and a solid particle diameter of not more than 0,06 mm, for use in the manufacture of car air-conditioning systems 0 %p/st31.12.20240.7996ex8418999020 Aluminium connecting block for connecting to a condenser manifold in welding process: hardened to T6 or T5 temper, with a weight of not more than 150 g, with a length of 20 mm or more but not more than 150 mm, with a fixing rail in one piece 0 %p/st31.12.2025 0.8004ex8418999030 Receiver dryer profile for connecting to a condenser manifold in welding process with: a braze flatness of not more than 0,2 mm, a weight of 100 g or more but not more than 600 g, a fixing rail in one piece 0 %p/st31.12.20250.6231ex8421210020 Water pre-treatment system comprising one or more of the following elements, whether or not incorporating modules for sterilization and sanitization of these elements: ultrafiltration system carbon filtration system water softener system for use in a biopharmaceutical laboratory 0 %p/st31.12.20240.3375ex8421999091Parts of equipment, for the purification of water by reverse osmosis, consisting of a bundle of hollow fibres of artificial plastic material with permeable walls, embedded in a block of artificial plastic material at one end and passing through a block of artificial plastic material at the other end, whether or not housed in a cylinder0 %p/st31.12.20240.6193ex8431200040Aluminium core, plastic tank radiator, with integral steel support structure and an open core square wave design of 9 fins per 2,54 cm of core length for use in the manufacture of vehicles of heading 84270 %p/st31.12.20240.6821ex8436990010 Part containing: a single-phase AC motor, an epicyclic gearing, a cutter blade, and whether or not containing: a capacitor, a part fitted with a threaded bolt, for use in the manufacture of garden shredders 0 %p/st31.12.20250.3374ex8439990010Suction-roll shells, produced by centrifugal casting, not drilled, in the form of alloy-steel tubes, of a length of 3000 mm or more and an external diameter of 550 mm or more0 %p/st31.12.2024 0.2599ex8477809910Machines for casting or for surface modification of plastic membranes of heading 39210 %p/st31.12.20240.8123ex8479899728 Integrated electric brake unit for immediate generation of the hydraulic pressure during braking, full electronic brake control and enabling regenerative braking of motor vehicles with: electronic brake assistants, hydraulic unit driven by brushless electric motor, brake fluid reservoir, for use in the manufacture of plug-in hybrid passenger cars 0 %-31.12.20250.7517ex8479899735 Mechanical unit ensuring the movement of the camshaft with: 6 or 8 oil chambers,

a phasing range of at least 18° but not more than 62°, a steel and/or steel alloy sprocket, a steel and/or steel alloy and/or aluminium alloy rotor 0 %-31.12.20240.8206 ex84798997 ex85013100 38 68 Camshaft actuator for controlling the timing of valve opening by using electromotor in a continuous variable valve timing system of an internal combustion piston engine, of: a length of 110 mm or more but not more than 140 mm, a width of 90 mm or more but not more than 130 mm, a height of 80 mm or more but not more than 110 mm for use in the manufacture of engines of motor vehicles 0 %-31.12.20260.7979ex8479899755Integrated automated turnkey machinery line for manufacturing jelly rolls of cylindrical lithium ion battery cells by winding, tab assembly and cutting of cathode, separator and anode0,8 %-31.12.20240.6230ex8479899760 Bioreactor for biopharmaceutical cell culture having interior surfaces of austenitic stainless steel, and with a process capacity up to 15000 litres, whether or not combined with a clean-in-process system and/or a dedicated paired media hold vessel 0 %p/st31.12.2026 0.7982ex8479899765Integrated automated turnkey machinery line for the assembly of battery cells to cylindrical lithium ion batteries with a speed of 300 parts per minute and production line0,8 %-31.12.20240.6573ex8479899770Machine to accurately align and attach lenses into a camera assembly in five axis alignment capability and fix them in position with a two part cure epoxy0 %p/st31.12.20240.7964ex8479907040 Housing of the rotor part of the mechanical unit ensuring the adjustment of movement of the camshaft compared to the crankshaft: of a circular shape, made of steel alloy with sintering process, with not more than 8 oil chambers, with a Rockwell hardness of 55 or more, with a density of 6,5 g/cm3, or more, but not more than 6,7 g/cm3 0 %-31.12.20250.7962ex8479907050 Rotor part of the mechanical unit ensuring the movement of the camshaft compared to the crankshaft: with 4 blades that end in grooves, made of steel alloy with sintering process 0 %-31.12.20250.7375 ex84811019 ex84811099 30 20 Electromagnetic pressure reducing valve with a plunger, with an operating pressure of not more than 325 MPa, with a plastic connector with 2 silver or tin, or silver-plated, or tin-plated, or silver and tin plated pins 0 %-31.12.20240.7424ex8481109940 Pressure reducing valves in a brass case with: a length of not more than 30 mm (± 1 mm), a width of not more than 18 mm (± 1 mm), of a kind used for incorporation in fuel delivery modules of motor vehicles 0 %-31.12.20270.7968 ex84813091 ex84813099 30 50 Mechanical check (non-return) valve for opening and closing of the flow of fuel: with an operating pressure of not more than 250 MPa, with a flow rate of 45 cm3/minute or more, but not more than 55 cm3/minute, with 4 input holes, each of them with a diameter of 1,2 mm or more, but not more than 1,6 mm, made of steel 0 %-31.12.2025 0.4668ex8481309191 Steel check (non-return) valves with:

an opening pressure of not more than 800 kPa, an external diameter not more than 37 mm 0 %p/st31.12.20240.7850ex8481309930 Brake booster check valve assembly containing at least: three vulcanized rubber hoses, one membrane valve, two metal clamps, one metal holder, whether or not connecting metal pipe, for use in the manufacture of motor vehicles 0 %-31.12.20240.3363ex8481805910Air control valve, consisting of a stepping motor and a valve pintle, for the regulation of idle air flow in fuel injection engines0 %p/st31.12.20240.7155ex8481805920Pressure regulating valve for incorporation into compressors of motor vehicle air condition units0 %p/st31.12.20260.7380ex8481805930 Two-way flow control valve with housing, with: at least 5, but not more than 16 outlet holes with at least 0,05 mm, but not more than 0,5 mm diameter, at least 330 cm3/minute, but not more than 5000 cm3/minute flow rate, at least 19, but not more than 300 MPa operating pressure 0 %-31.12.20240.7377ex8481805940 Flow-control valve: made of steel, with an outlet hole with a diameter of 0,05 mm or more, but not more than 0,5 mm, with an inlet hole with a diameter of 0,1 mm or more, but not more than 1,3 mm, with chromium nitride coating, with a surface roughness of Rp 0,4 0 %-31.12.20270.7381ex8481805950 Electromagnetic valve for quantity control with: a plunger, a solenoid with a of coil resistance of at least 1,85 Ohm, but not more than 8,2 Ohm 0 %-31.12.2027 0.7382ex8481805960 Electromagnetic valve for quantity control with a solenoid with a coil resistance of at least 0,19 Ohm, but not more than 0,66 Ohm, and with an inductance of not more than 1 mH 0 %-31.12.20270.7960 ex84818059 ex84819000 70 80 Flow-control valve made of steel, with an outlet hole with a diameter of at least 0,05 mm, but not more than 0,5 mm, with an inlet hole with a diameter of at least 0,1 mm, but not more than 1,3 mm 0 %-31.12.20250.5575ex8481806960 Four-way reversing valve for refrigerants, consisting of: a solenoid pilot valve a brass valve body including valve slider and copper connections with a working pressure up to 4,5 MPa 0 %p/st31.12.20270.7519 ex84818073 ex84818099 20 70 Pressure- and flow-control valve controlled by external electromagnet: made of steel and/or steel alloy(s), without integrated circuit, of not more than 1000 kPa operating pressure, with a flow quantity of not more than 5 l/min, without an electromagnet 0 %-31.12.20240.7637 ex84818079 ex84818099 30 30 Service Valve which suits for R410A or R32 gas while connecting indoor and outdoor units with: a withstanding pressure of the valve body of 6,3 MPa, a leakage ratio of less than 1,6 g/a, an impurity ratio of less than 1,2 mg/PCS, an airtight pressure of the valve body of 4,2 MPa, for use in the manufacture of air conditioners 0 %-31.12.20240.7518ex8481900040 Valve armature: for the opening and closing of the flow of fuel, consisting of a shaft and a blade, with at least 3 but not more than 8 holes on the blade, made of metal and/or metal alloy(s)

0 %-31.12.2024 0.6391 ex84821010 ex84821090 ex84825000 10 10 10 Ball and cylindrical bearings: with an outside diameter of 28 mm or more but not more than 140 mm, with an operational thermal stress of more than 150°C at a working pressure of not more than 14 MPa, for the manufacture of machinery for the protection and control of nuclear reactors in nuclear power plants 0 %p/st31.12.20240.7735ex8482101015 Ball bearings with: an internal diameter of 4 mm or more but not more than 9 mm, an external diameter of not more than 26 mm, a width of not more than 8 mm, for use in the manufacture of electromotors with a range of 40000 rpm or more but not more than 80000 rpm 0 %-31.12.20240.7707 ex84821010 ex84821090 25 40 Double row ball bearings / ball bearing cartridges: with an internal diameter of 3 mm or more, but not more than 9 mm, with an external diameter of 17 mm or more, but not more than 36 mm, with a width of 6 mm or more, but not more than 69 mm, manufactured according to ISO standard 492 - Class 5 or DIN 620 - P5 or ANSI Standard 20 - ABEC 5, with ceramic balls, for use in turbo compressors (turbochargers) 0 %-31.12.20240.8098ex8482500020 Axial roller bearing made of steel: the retainer is made of cold-rolled steel with a carbon content of up to 0,25 percent, complying with standard ASTM A109-98, the rollers are made of anti-friction steel according to ASTM 295-94, with an external diameter of 63 mm or more but not more than 66 mm, with an internal diameter of 44 mm or more but not more than 46 mm, with a weight of 23 g or more but not more than 27 g, with 36 rollers or more but not more than 38 rollers 0 %p/st31.12.2025 0.8588ex8483109530 Steel alloy splined shaft (torque shaft) with straight teeth and involute profile, with: external toothing in a diametral pitch standard, 17 teeth or more, but not more than 50 teeth, a diameter of 35 mm or more, but not more than 145 mm, a length of 200 mm or more, but not more than 1345 mm, a hardness of 35 HRC or more, but not more than 45 HRC 0 %-31.12.20280.5744 ex84833032 ex84833038 30 60 Bearing housing of a kind used in turbochargers: of precision-cast grey cast iron complying with standard DIN EN 1561 or precision-cast ductile cast iron complying with DIN EN 1560, with oil chambers, without bearings, with a diameter of 50 mm or more, but not more than 250 mm, with a height of 40 mm or more, but not more than 150 mm, whether or not with water chambers and connectors 0 %p/st31.12.20270.8303ex8483402520 Worm gearbox: in an aluminium alloy housing, with a plastic or steel worm, with mounting holes, with a 90 degree reversible drive direction, with a 4:19 transmission ratio, equipped with a lead screw with a length of 310 mm or more but not more than 380 mm, with a guide nut incorporated into the assembly bracket, with or without a lead screw support, for indirect connection to the drive motor of a car seat guide system 0 %-31.12.20260.5202ex8483402950 Gear set of cycloid gear type with: a rated torque of 50 Nm or more but not more than 9000 Nm,

standard ratios of 1:50 or more but not more than 1:475, lost motion of not more than one arc minute, an efficiency of more than 80 % of a kind used in robot arms 0 %p/st31.12.2026 0.5977ex8483402960 Epicyclic gearing, of a kind used in driving hand-held power tools with: a rated torque of 25 Nm or more, but not more than 70 Nm, standard gear ratios of 1:12.7 or more, but not more than 1:64.3 0 %p/st31.12.20240.8585ex8483402970 Cast steel planetary cage, with: external or internal toothing in a diametral pitch standard, 27 teeth or more, but not more than 70 teeth, a diameter of 300 mm or more, but not more than 725 mm, a length of 225 mm or more, but not more than 800 mm, 3 or 4 planetary gears, a hardness of 40 HRC or more, but not more than 45 HRC 0 %-31.12.20280.2503ex8483405120Gear box, having a differential with wheel axle, for use in the manufacture of self-propelled lawnmowers with a seat of subheading 843311510 %p/st31.12.20240.7920ex8483405930 Hydrostatic speed changer: with a hydro pump and a differential with wheel axle, whether or not with a fan impeller and/or a pulley, for use in the manufacture of lawn mowers of subheadings 843311 and 843319 or other mowers of subheading 843320 0 %p/st31.12.20240.4997ex8483409080 Transmission gearbox, with: not more than 3 gears, an automatic deceleration system, and a power reversal system, for use in the manufacture of goods of heading 8427 0 %p/st31.12.20250.8100ex8483508020 Pulley blocks of non-cast steel: made of structural carbon steel complying with standard JIS G4051, with an external diameter of 114 mm or more but not more than 118 mm, with an internal diameter of 33 mm or more but not more than 37 mm, with a width of 29 mm or more but not more than 33 mm, with a weight of 0,6 kg or more but not more than 0,9 kg, with 6 trapezoidal grooves 0 %p/st31.12.2025 0.8540ex8483508030 Mechanical tensioner for maintaining the tension of the drive belts of a passenger car engine: with two pulleys made of polyamide, each of them with a diameter of 50 mm or more but not more than 70 mm, with a spring made of a steel alloy containing chromium and silicon, with two arms made of aluminum, with a holder made of aluminum, for use in the manufacture of motor vehicle engines 0 %-31.12.20280.8209ex8483908920 Sprocket for continuous variable valve timing to optimize the process of filling the cylinders of an internal combustion engine with: case, rotor, at least 4 screws, spring, of an external diameter of 80 mm or more but not exceeding 95 mm, of a thickness of 25 mm or more but not more than 35 mm, for use in the manufacture of engines of motor vehicles 0 %-31.12.20260.8584ex8483908930 Forged steel sprockets with external toothing, whether or not with internal splines in a diametral pitch standard, with: a diameter of 400 mm or more, but not more than 630 mm, 7 teeth or more, but not more than 15 teeth, a tooth core hardness of 28 HRC or more, but not more than 45 HRC, a tooth surface hardness of 50 HRC or more, but not more than 60 HRC,

whether or not, a spline hardness of 30 HRC or more, but not more than 45 HRC, an effective carburized case depth of 4 mm or more, but not more than 5 mm 0 %-31.12.2028 0.8541ex8483908940 Steel alloy gear wheels with straight teeth and involute profile, with: external and/or internal toothing in a diametral pitch standard, a diameter of 35 mm or more, but not more than 600 mm, 13 teeth or more, but not more than 80 teeth, a tooth core hardness of 28 HRC or more, but not more than 45 HRC, a tooth surface hardness of 50 HRC or more, but not more than 65 HRC, an effective carburized case depth of 1,00 mm or more, but not more than 3,1 mm, a spline hardness of 27 HRC or more, but not more than 62 HRC, whether or not in combination with a shaft with a spline hardness of 27 HRC or more, but not more than 62 HRC 0 %-31.12.20280.7156ex8484200010Mechanical shaft seal for incorporation into rotary compressors for use in the manufacture of motor vehicle air condition units0 %p/st31.12.20260.7604ex8484200020Mechanical face sealing device made of two movable rings (one ceramic mating, with a thermal conductivity lower than 80W/mK and the other carbon sliding), one spring and a nitrile sealant on the external side0 %-31.12.20240.6854ex8501101020 Synchronous motor for a dishwasher with a water flow control mechanism with a length without axle of 24 mm (± 0,3), a diameter of 49,3 mm (± 0,3), a rated voltage of 220 V AC or more but not more than 240 V AC, a rated frequency of 50 Hz or more but not more than 60 Hz, an input power of not more than 4 W, a rotation speed of 4rpm or more but not more than 4,8rpm, an output torque of not less than 10kgf/cm 0 %-31.12.2027 0.7601ex8501101030 Motors for air pumps, with: operating voltage of 9 VDC or more but not more than 24 VDC, operating temperature range of -40°C or more but not more than 80°C, an output not exceeding 18 W, for use in the manufacture of pneumatic support and ventilation systems for car seats 0 %-31.12.20240.7857ex8501101040 Synchronous hybrid stepper motor with: an output not exceeding 18 W, two phases, a rated current of not more than 2,5 A/phase, a rated voltage of not more than 20 V, with or without a threaded shaft, for use in the manufacture of 3D printers 0 %-31.12.20240.8390 ex85011010 ex85011099 50 30 Linear actuator for automotive electric seat adjustment applications: consisting of a permanently excited DC motor with an integrated gear mechanism and leadscrew, whether brushed or brushless, whether or not with electronic control unit, whether or not with Hall Effect Sensor, with a nominal voltage of 8 V or higher but not higher than 16 V, with a rated output mechanical power not exceeding 20 W, and with a specified temperature range from -40 °C to 160 °C, for use in the manufacture of automotive components for car seats 0 %-31.12.20270.8389 ex85011010 ex85011099 60 40 Rotary actuator for automotive electric seat adjustment applications: consisting of a permanently excited DC motor with an integrated gear mechanism,

whether brushed or brushless, whether or not with electronic control unit, whether or not with Hall Effect Sensor, with a nominal voltage of 8 V or more but not more than 16 V, with a rated output mechanical power not exceeding 35 W, and with a specified temperature range from -40 °C to 160 °C, for use in the manufacture of automotive components for car seats 0 %-31.12.2027 0.8539ex8501101070 Electric controller for blinds of cooler, with an operating DC voltage of 9 V or more but not more than 16 V and a maximum power of less than 18 W, containing at least: a printed circuit board, an electric stepper motor, a connector, a plastic cover, for use in the manufacture of goods of Chapter 87 0 %-31.12.20280.8394ex8501109920 Worm axis motor for automotive electric seat adjustment applications: consisting of a permanently excited DC motor with a worm wheel, whether brushed or brushless, whether or not with electronic control unit, whether or not with Hall Effect Sensor, with a nominal voltage of 8 V or more but not more than 16 V, with a rated output mechanical power not exceeding 35 W, and with a specified temperature range from -40 °C to 160 °C, for use in the manufacture of automotive components for car seats 0 %-31.12.20270.8396ex8501109950 Electric (DC) motor powering height adjusting with: a rated output mechanical power not exceeding 35 W, frame integration with a length of 156 mm, a height of 59 mm, a thickness of 36 mm and a weight of 500 g, a stall torque of 45 Nm and ultimate torque of 200 Nm, a maximum current of 15 A, no load speed of 7 RPM or more but not more than 10 RPM, a rotation speed of 4000 RPM or more but not more than 5600 RPM, a maximum noise level of 42 dB(A), a maximum angular backlash up to 3 degrees, and a 8 tooth pinion module, for use in the manufacture of automotive components for car seats 0 %-31.12.2027 0.7197ex8501109956 DC Motor: with a speed rotation of not more than 7000 rpm without load, with a nominal voltage of not more than 18 V, with a maximum power of 24 W, for a specific temperature range from -40°C to 160°C, with or without a gear connection, with or without a mechanical attachment interface, with 2 electrical connections, with a maximum torque of 100 Nm 0 %-31.12.20260.7198ex8501109958 DC Motor : with a speed rotation of not more than 6500 rpm (without load), with a nominal voltage of 12 V (± 4 V), with a maximal power below than 20 W, with a specified temperature range from -40°C to 160°C, with a worm gear drive, with a mechanical attachment interface, with 2 electrical connections, with a maximum torque of 75 Nm 0 %-31.12.20260.5846ex8501109960 DC motor: with a rotor speed of 3500 rpm or more but not more than 5000 rpm loaded and not more than 6500 rpm when not loaded with a power supply voltage of 100 V or more but not more than 240 V for use in the manufacture of electric fryers 0 %-31.12.20270.6858ex8501109964 DC motor to control angular position of the flap to adjust gas flow in the Air Throttle and EGR valve:

with Ingress Protection (IP) standard of IP69, with a rotor speed of not more than 6500 rpm when not loaded, with a rated voltage of 12,0 V (± 0,1), of a specified temperature range of – 40 °C or more but not more than + 165 °C, with or without a connecting pinion, with or without an engine connector, with or without a flange, with a diameter of not more than 40 mm (not including the flange), with an overall height of not more than 90 mm (from the base to the pinion) 0 %-31.12.2026 0.6880ex8501109965 Electric turbocharger actuator, with: a DC motor, an integrated gear mechanism, a (pulling)force of 200 N or more at a minimum of 140°C elevated ambient temperature, a (pulling) force of 250 N or more in each position of its stroke, an effective stroke of 15 mm or more but not more than 25 mm, with or without an on-board diagnostics interface 0 %-31.12.20250.6115ex8501109970 DC stepping motor, with: a two-phase winding, a rated voltage of 9 V or more, but not more than 16,0 V, of a specified temperature range of - 40 °C or more but not more than + 105 °C, with or without connection pinion, with or without motor drive connector 0 %-31.12.20240.6627ex8501109975 Permanently excited DC motor with a multiple-phase winding, an external diameter of 24 mm or more but not more than 38 mm, a rated speed of not more than 12000 rpm, a power supply voltage of 8 V or more but not more than 27 V, with or without a pulley, with or without a gear wheel 0 %-31.12.20250.2838ex8501109979DC motor with brushes and an internal rotor with a three-phase winding, whether or not equipped with a worm or a pinion, of a specified temperature range covering at least - 20°C to + 70°C0 %-31.12.20240.4555ex8501109980 DC stepping motor, with: an angle of step of 7,5° (± 0,5°), a pull-out torque at 25 °C of 25 mNm or more, a pull-out pulse rate of 1500 pps or more, a two-phase winding, and a rated voltage of 10,5 V or more, but not more than 16,0 V 0 %-31.12.2024 0.7250ex8501200040 Universal AC/DC motor with: a rated output of 50 W but not higher than 1,2 kW, a supply voltage of 230 V, whether or not with engine brake, whether or not assembled to a reduction gear with output shaft, which is contained in a housing, whether or not fitted with a motor control/motor switch connected by cable, and whether or not with fan, for use as electric drive of lawnmower blades or domestic appliances 0 %-31.12.20240.8345ex8501200050 Universal AC/DC motor, rotating: with a nominal supply voltage of 230 V, with a power of more than 37,5 W but not more than 2000 W, with a stator cross-section of 93 mm or more but not more than 103 mm and a thickness of 15 mm or more but not more than 45 mm, and with or without a worm gear, gears or a gearbox, for the production of a torque to a transmission shaft for small domestic appliances 0 %-31.12.20270.8349ex8501200060 Universal AC/DC motor, rotating: with a nominal supply voltage of 230 V, with a power of more than 37,5 W but not more than 1200 W, with a stator cross-section of 65 mm or more but not more than 75 mm and a thickness of 15 mm or more but not more than 45 mm, and

with or without a worm gear, gears or a gearbox, for the production of a torque to a transmission shaft for small domestic appliances 0 %-31.12.20270.8367ex8501200070 Universal AC/DC motor, rotating: with a nominal supply voltage of 230 V, with a power of more than 37,5 W but not more than 700 W, with a stator cross-section of 49 mm or more but not more than 59 mm and a thickness of 15 mm or more but not more than 45mm, and with or without a worm gear, gears or a gearbox, for the production of a torque to a transmission shaft for small domestic appliances 0 %-31.12.2027 0.5954ex8501310045 DC motors, brushless, with: an external diameter of 90 mm or more, but not more than 110 mm, a rated speed of not more than 3680 rpm, an output of 600 W or more but not more than 740 W at 2300 rpm and at 80 °C, a supply voltage of 12 V, a torque of not more than 5,67 Nm, a rotor position sensor, an electronic star-point relay, and for use with an electric power steering control module 0 %-31.12.20240.8395ex8501310047 Motor for automotive electric seat adjustment applications: with a shaft output on both motor sides, consisting of a permanently excited DC motor, whether brushed or brushless, whether or not with electronic control unit, whether or not with Hall Effect Sensor, with a nominal voltage of 8 V or more but not more than 16 V, with a rated output mechanical power not exceeding 120 W, and with a specified temperature range from -40 °C to 160 °C, for use in the manufacture of automotive components for car seats 0 %-31.12.20270.5577ex8501310050 DC motors, brushless, with: an external diameter of 80 mm or more, but not more than 200 mm, a supply voltage of 9 V or more, but not more than 16 V, an output at 20 °C of 300 W or more, but not more than 750 W, a torque at 20 °C of 2,00 Nm or more, but not more than 7,00 Nm, a rated speed at 20 °C of 600 rpm or more, but not more than 3100 rpm, with or without a pulley, with or without an electronic power steering sensor/controller 0 %-31.12.2027 0.5978 ex85013100 ex85013200 55 40 DC motor with or without commutator, with an external diameter of 24,2 mm or more, but not more than 140 mm, a rated speed of 3300 rpm or more, but not more than 26200 rpm, a rated supply voltage of 3,6 V or more, but not more than 230 V, an output power of more than 37,5 W, but not more than 2400 W, a free load current of not more than 20,1 A, a maximum efficiency of 50 % or more, for driving hand-held power tools or lawn mowers 0 %-31.12.20240.4731ex8501310058 Permanently excited DC motor with: an external diameter of 30 mm or more but not more than 90 mm, including mounting flange, a rated speed of not more than 15000 rpm, an output of 45 W or more but not more than 400 W, and a supply voltage of 9 V or more but not more than 50 V, whether or not a multiple-phase winding, whether or not with a drive disc, whether or not with a crankcase, whether or not with a fan, whether or not with a cap assembly, whether or not with a sun gear, whether or not with a speed and rotational direction encoder,

whether or not with or without a speed or rotational direction sensor of resolver type or Hall effect type, whether or not with a mounting flange for use in the manufacture of air suspension seats in tractors, earthmoving machines and forklifts or for use in the manufacture of actuators for height-adjustable furniture 0 %-31.12.2024 0.6809 ex85013100 ex85013200 63 65 Ready for installation in vehicles or equipment of headings 8432 and 8433, brushless and permanently excited direct current motor with: a specified speed of not more than 4100 rpm, a minimum output of 400 W, but not more than 1,3 kW (at 12 V), or with a minimum output of 750 W but not more than 1,55 kW (at 36 V), a flange diameter of 85 mm or more but not more than 200 mm, a maximum length of 335 mm, measured from the beginning of the shaft to the outer ending, a housing length of not more than 265 mm, measured from the flange to the outer ending, a maximum of two-piece (basic housing including electric components and flange with minimum 2 and maximum 11 bore holes) aluminium diecast or sheet steel housing whether or not with a sealing compound (groove with an O-ring and grease), a stator with single T-tooth design and single coil windings in 9/6 or 12/8 topology, and surface magnets, whether or not with electronic power steering controller, whether or not with pulley, whether or not with rotor position sensor 0 %-31.12.20250.4855 ex85013300 ex85014080 ex85015350 30 50 10 Electric drive for motor vehicles, with an output of not more than 315 kW: with an AC or DC motor with or without transmission, with or without power electronics 0 %-31.12.20260.8188ex8501402035 Electric AC motor, single-phase, with: a rated power of 120 W or more but not more than 150 W, an input power of 280 W or more but not more than 350 W, an external diameter without bracket connector and pulley of 145 mm or more but not more than 160 mm, a rated speed of 2680 rpm or more but not more than 3000 rpm, a weight of 4,2 kg or more but not more than 4,6 kg, pulleys, a spindle and a tachometer, for use in the manufacture of home appliance products 0 %-31.12.2026 0.8189ex8501402045 Electric AC motor, single-phase, with: a rated power of 275 W or more, but not more than 325 W, an input power of 600 W or more but not more than 700 W, an external diameter without bracket and connector of 150 mm or more but not more than 170 mm, a rated speed of 15000 rpm or more but not more than 20000 rpm, a weight of 4,2 kg or more, a pulley and a tachometer, for use in the manufacture of home appliance products 0 %-31.12.20260.8191ex8501402050 Electric AC motor, single-phase, with: a rated power of 300 W or more but not more than 370 W, an input power of 600 W or more but not more than 700 W, an external diameter without bracket and connector of 150 mm or more but not more than 170 mm, a rated speed of 15000 rpm or more but not more than 19000 rpm, a weight of 4,8 kg or more, a pulley, for use in the manufacture of home appliance products

0 %-31.12.20260.8192ex8501402055 Electric AC motor, single-phase, with: a rated power of 275 W or more, but not more than 325 W, an input power of 600 W or more but not more than 700 W, an external diameter without bracket and connector of 160 mm or more but not more than 180 mm, a rated speed of 15000 rpm or more but not more than 19000 rpm, a weight of not more than 4,4 kg, a pulley, for use in the manufacture of home appliance products 0 %-31.12.2026 0.8193ex8501402060 Electric AC motor, single-phase, with: a rated power of 275 W or more but not more than 325 W, an output power of 550 W or more but not more than 600 W, an input power of 800 W or more but not more than 1000 W, an external diameter of more than 150 mm but not more than 170 mm without the bracket, a rated speed of more than 16000 rpm but not more than 18000 rpm, a weight of 3,4 kg or more but not more than 3,7 kg, a pulley, for use in the manufacture of home appliance products 0 %-31.12.20260.5329 ex85015100 ex85015220 30 50 AC synchronous servo motor with resolver and brake for a maximum speed of not more than 6000 rpm, with: an output of 340 W or more but not more than 7,4 kW, a flange of dimensions of not more than 180 mm × 180 mm, and a length from flange to extreme end of resolver of not more than 271 mm 0 %-31.12.20260.8190ex8501510040 Electric AC motor, three-phase, with: a rated power of 280 W or more but not more than 320 W, an output power of 480 W or more but not more than 540 W, an input power of 800 W or more but not more than 900 W, an external diameter of 150 mm or more but not more than 170 mm, a rated speed of 15000 rpm or more but not more than 20000 rpm, a weight of 6 kg or more but not more than 6,4 kg, a pulley and a tachometer, for use in the manufacture of home appliance products 0 %-31.12.20260.8404ex8501510050 Three phase AC synchronous brushless permanent magnet motor with: an output of 500 W or more but not more than 700 W, an external diameter of 129,7 mm or more but not more than 180,3 mm, a rated speed of 16000 rpm or more but not more than 17000 rpm, a weight of 2,5 kg or more but not more than 3,1 kg, and with a pulley, for use in the manufacture of home appliance products 0 %-31.12.2027 0.8590 ex85015100 ex85015220 60 60 Automotive-ready brushless permanently excited magnet synchronous AC-motor with a specified speed of not more than 7000 rpm, a power rating of 400 W or more but not more than 1,8 kW (at 12 V), a flange diameter of 80 mm or more, but not more than 200 mm, a maximum length of not more than 220 mm, measured from the beginning of the shaft to its outer end, a housing length of not more than 180 mm, measured from the flange to the outer end, a steel sheet or die-cast aluminium basic housing consisting of not more than two parts, including electrical components and a flange with two or more but not more than 11 holes, whether or not with a sealing connection (groove with O-ring and protective grease or liquid seal interface), a stator with single T-tooth design and single coil winding with 12/10 or 12/8 topology and surface magnets

0 %-31.12.20280.6511ex8501535020 AC traction motor of the Interior Permanent Magnet Synchronous Motor (IPMSM) type with: a torque output of 200 Nm or more, but not more than 400 Nm, a power output of 50 kW or more, but not more than 200 kW , a rotation speed of no more than 15000 rpm, for use in the manufacture of electric vehicles 0 %-31.12.20240.8129ex8501535030 Permanent magnet synchronous traction motor, with: a continuous power of 110 kW or more but not more than 180 kW, a liquid cooled system, a total length of 500 mm or more but not more than 650 mm, a total width of 600 mm or more but not more than 700 mm, a total height of 550 mm or more but not more than 650 mm, weighing of not more than 350 kg, 3 suspension points 0 %-31.12.2025 0.8285ex8501535040 Permanent magnet traction AC motor, with: a continuous power of 110 kW or more but not more than 150 kW, a liquid cooled system, a total length of 460 mm or more but not more than 590 mm, a total width of 450 mm or more but not more than 580 mm, a total height of 490 mm or more but not more than 590 mm, a weight of not more than 310 kg, 4 mounting points 0 %-31.12.20260.8458ex8501535050 Asynchronous traction motor, with: a continuous power of 140 kW or more but not more than 180 kW, a liquid cooled system, a total length of 580 mm or more but not more than 730 mm, a total width of 550 mm or more but not more than 670 mm, a total height of 510 mm or more but not more than 630 mm, with a weight of not more than 390 kg, with or without reduction gear, with or without starter generator, 2 mounting points, for use in the manufacture of the electric drive of hybrid buses 0 %-31.12.20270.8130ex8501620040 AC, 3-phase generator, with: a continuous power of 147 kVA or more but not more than 222 kVA, a continuous torque of 650 Nm or more but not more than 900 Nm, a maximum working speed of 2700 revolutions per minute (rpm), a liquid cooled system, a length of 100 mm or more but not more than 200 mm, a width of 550 mm or more but not more than 650 mm, a height of 550 mm or more but not more than 650 mm, weighing of not more than 150 kg 0 %-31.12.20250.2837 ex85030091 ex85030099 31 32 Rotor, at the inner side provided with one or two magnetic rings (uniform or sectional) whether or not incorporated in a steel ring or bearing mounted in steel housing0 %p/st31.12.2024 0.2836ex8503009931Stamped collector of an electric motor, having an external diameter of not more than 16 mm0 %p/st31.12.20240.4599ex8503009933Stator for brushless motor of electrical power steering with a roundness tolerance of 50 µm0 %p/st31.12.20260.4601ex8503009934Rotor for brushless motor of electrical power steering with a roundness tolerance of 50 µm0 %p/st31.12.20240.7496ex8503009937 Rotor for an electric motor, with the rotor cylindrical body made of agglomerated ferrite and plastics and the shaft made of metal with: diameter of the rotor body of 17 mm or more but not more than 37 mm, length of the rotor body of 12 mm or more but not more than 36 mm,

shaft length of 52 mm or more but not more than 82 mm 0 %-31.12.20240.6161ex8503009955 Stator for brushless motor, with: an internal diameter of 206,6 mm (± 0,5), an external diameter of 265,0 mm (± 0,2), and a width of 37,2 mm or more but not more than 47,8 mm, of a kind used in the manufacture of washing machine, washer-dryer or dryer equipped with direct drive drums 0 %p/st31.12.20250.6379ex8503009960Engine cover for electronic belt drive steering system of galvanized steel with a thickness of not more than 2,5 mm (± 0,25 mm)0 %p/st31.12.20240.7760ex8503009965 Rotor body of stacked electrical sheet having: a diameter of 18 mm or more but not more than 35 mm, and a length of 20 mm or more but not more than 65 mm 0 %-31.12.20240.7761ex8503009975 Stator body of stacked electrical sheet having: an inner diameter of 18 mm or more but not more than 35 mm, an outer diameter of 35 mm or more but not more than 65 mm, and a length of 20 mm or more but not more than 65 mm, whether or not incorporated in a housing 0 %-31.12.2024 0.7758ex8503009980 Steel motor housing having: an inner diameter of 35 mm or more but not more than 65 mm, an outer diameter of 35 mm or more but not more than 70 mm, and a length of 35 mm or more but not more than 150 mm 0 %-31.12.20240.7549ex8504318015 Electrical Transformer with a capacity of 192 Watts or 216 Watts dimensions of not more than 27,1 x 26,6 x 18 mm an operating temperature range of – 40 °C or more, but not more than + 125 °C three or four inductively coupled copper wire windings and 9 connection pins at the bottom 0 %-31.12.20240.7548ex8504318025 Electrical Transformer with a capacity of 432 Watts dimensions of not more than 24 mm x 21 mm x19 mm an operating temperature range of – 20 °C or more, but not more than + 85 °C two windings and 5 connection pins at the bottom 0 %-31.12.20240.4450ex8504318030Switching transformers, having a power handling capacity of not more than 1 kVA for use in the manufacture of static converters0 %-31.12.20240.7547ex8504318035 Electrical Transformer with a capacity of 433 Watts dimensions of not more than 37,3 x 38,2 x 28,5 mm an operating temperature range of – 40 °C or more, but not more than + 125 °C four inductively coupled copper wire windings and 13 connection pins at the bottom 0 %-31.12.20240.7551ex8504318045 Electrical Transformer with: a capacity of 0,2 Watts, dimensions of not more than 15 mm x 15,5 mm x 14 mm, an operating temperature range of – 10 °C or more, but not more than + 125 °C, two inductively coupled copper wire windings, 5 connection pins at the bottom, and a copper shielding 0 %-31.12.2024 0.7000ex8504318050Transformers for use in the manufacture of electronic drivers, control devices and LED light sources for lighting industry0 %-31.12.20260.7764ex8504318055 Electrical transformer with: a capacity of 0,22 kVA or more, but not more than 0,24 kVA, an operating temperature range of + 10°C or more, but not more than + 125°C, four or five inductively coupled copper wire windings,

11 or 12 connection pins at the bottom, and dimensions of not more than 32 mm x 37,8 mm x 25,8 mm 0 %-31.12.20240.7029ex8505111047 Articles in the form of a triangle, square, rectangle, or trapezoid, whether or not arched, with rounded corners or oblique sides, intended to become permanent magnets after magnetisation, containing neodymium, iron and boron, with the following dimensions: a length of 9 mm or more but not more than 105 mm, a width of 5 mm or more but not more than 105 mm, and a height of 2 mm or more but not more than 55 mm 0 %-31.12.20260.5584ex8505111050 Bars specifically shaped, intended to become permanent magnets after magnetisation, containing neodymium, iron and boron, with dimensions: a length of 15 mm or more but not more than 52 mm, a width of 5 mm or more but not more than 42 mm, of a kind to be used in the manufacture of electric servomotors for industrial automation 0 %p/st31.12.20270.7567ex8505111053 Permanent magnets of a neodymium alloy cylindrical shaped with notch with internal threaded bore on one side, with a length of 97,5 mm or more, but not more than 225 mm a diameter of 19 mm or more, but not more than 25 mm 0 %-31.12.20240.5585ex8505111063 Rings, tubes, bushings or collars made from an alloy of neodymium, iron and boron, with an external diameter of not more than 45 mm, a height of not more than 45 mm, of a kind used in the manufacture of permanent magnets after magnetisation 0 %p/st31.12.2027 0.3740ex8505111065 Permanent magnets consisting of an alloy of neodymium, iron and boron, either in the shape of a rectangle, whether or not rounded, with a rectangular or a trapezoidal section having a length of not more than 140 mm, a width of not more than 90 mm and a thickness of not more than 55 mm, or in the shape of curved rectangle (tile type) having a length of not more than 75 mm, a width of not more than 40 mm, a thickness of not more than 7 mm and a radius of curvature of more than 86 mm but not more than 241 mm or in the shape of a disc with a diameter of not more than 90 mm, whether or not containing a hole in the centre 0 %p/st31.12.20240.7788ex8505111068 Blocks made of neodymium, iron and boron or an alloy of samarium and cobalt, whether or not covered with zinc, intended to become permanent magnets after magnetisation with: a length of 13,8 mm or more but not more than 45,2 mm, a width of 7,8 mm or more but not more than 25,2 mm, a height of 1,3 mm or more but not more than 4,7 mm 0 %-31.12.20240.5948ex8505111070 Disc consisting of an alloy of neodymium, iron and boron, covered with nickel or zinc, that after magnetisation is intended to become a permanent magnet whether or not containing a hole in the centre, with a diameter of not more than 90 mm, of a kind used in car loudspeakers 0 %-31.12.20240.6857 ex85051110 ex85051190 ex85051990 73 73 35 Articles in shape of flat bars, arched bars or quarter sleeves, made of ferrite, or cobalt, or samarium or other rare-earth metals, or their alloy, whether or not overmolded with polymers, intended to become permanent magnets after magnetisation with:

a length of 5 mm or more, but not more than 60 mm, a width of 5 mm or more, but not more than 40 mm, a thickness of 3 mm or more, but not more than 15 mm 0 %p/st31.12.2024 0.6347 ex85051110 ex85051190 75 75 A quarter sleeve intended to become permanent magnet after magnetization, consisting of at least neodymium, iron and boron, with a width of 9,1 mm or more but not more than 10,5 mm, with a length of 20 mm or more but not more than 30,1 mm, of a kind used on rotors for the manufacture of fuel pumps 0 %p/st31.12.20240.8508ex8505111078 Two permanent magnets made of a praseodymium-neodymium alloy, in a rectangular steel holder with an outer casing of rubber with outer dimensions: a length of 200 mm or more but not more than 205 mm, a width of 58 mm or more but not more than 62 mm, a height of 25 mm or more but not more than 30 mm, with a stud mounted in the middle 0 %-31.12.20270.7789ex8505191020 Arc segments of permanent magnets of agglomerated ferrite, with: a length of 16,8 mm or more, but not more than 110,2 mm, a width of 14,8 mm or more, but not more than 75,2 mm, a thickness of 4,8 mm or more, but not more than 13,2 mm, for use in the manufacture of electromotor rotors 0 %-31.12.20240.5937ex8505199030Articles of agglomerated ferrite in the shape of a disc with a diameter of not more than 120 mm, containing a hole in the centre intended to become permanent magnets after magnetisation with a remanence between 245 mT and 470 mT0 %-31.12.20240.7299ex8505199050 Article of agglomerated ferrite in the shape of a rectangular prism to become a permanent magnet after magnetisation whether or not with bevelled edges of a length of 27 mm or more but not more than 32 mm (± 0,15 mm), of a width of 8,5 mm or more but not more than 9,5 mm (+ 0,05 mm / -0,09 mm), of a thickness of 5,5 mm or more but not more than 5,8 mm (+ 0/-0,2 mm), and of a weight of 6,1 g or more but not more than 8,3 g 0 %p/st31.12.2027 0.7511ex8505199060 Articles of agglomerated ferrite in the shape of a half-sleeve or a quarter-sleeve, or with rounded corners, to intended to become permanent magnet after magnetisation with the following dimentions: a length of 10 mm or more but not more than 100 mm (± 1 mm), a width of 10 mm or more but not more than 100 mm (± 1 mm), a thickness of 2 mm or more but not more than 15 mm (± 0,15 mm) 0 %-31.12.20240.4029ex8505200030Electromagnetic clutch, for use in the manufacture of compressors of air conditioning machines of motor vehicles0 %p/st31.12.20240.8095ex8505909020 Electromagnetic clutch coil in a cylindrical metal housing: the metal housing is made of hot-rolled steel complying with standard JIS G 3131 - SPHE, the coil is made of copper wire, with a weight of 0,4 kg or more but not more than 0,7 kg, with a width of 22 mm or more but not more than 25 mm, with a plate reinforced to the coil (coil backplate) with an internal diameter of 44 mm or more but not more than 46 mm, with an external diameter of 88 mm or more but not more than 96 mm, without plunger,

with one connector 0 %p/st31.12.20250.6855ex8506501010 Lithium cylindrical primary cells with: a diameter of 14,0 mm or more but not more than 26,0 mm, a length of 2,2 mm or more but not more than 51 mm, a voltage of 1,5 V or more, but not more than 3,6 V, a capacity of 0,15 Ah or more, but not more than 5,00 Ah for use in the manufacture of telemetry and medical devices, electronic meters or remote controls 0 %-31.12.20240.2490ex8506509010Lithium iodine single cell battery the dimensions of which do not exceed 9 mm × 23 mm × 45 mm and a voltage of not more than 2,8 V0 %-31.12.20240.2488ex8506509030Lithium-iodine or lithium-silver vanadium oxide single cell battery of dimensions of not more than 28 mm × 45 mm × 15 mm and a capacity of not less than 1,05 Ah0 %-31.12.2024 0.5180ex8506900010Cathode, in rolls, for air zinc button cell batteries (hearing aid batteries)0 %-31.12.20240.6685ex8507600015 Cylindrical lithium-ion-accumulators or modules with: a nominal capacity of 8,8 Ah or more, but not more than 18 Ah, a nominal voltage of 36 V or more, but not more than 48 V, a power of 300 Wh or more, but not more than 648 Wh, for use in the manufacture of electric bicycles 1,3 %-31.12.20240.7663ex8507600018 Lithium-ion polymer accumulator equipped with a battery management system and can-bus interface with: a length of not more than 1600 mm, a width of not more than 448 mm, a height of not more than 395 mm, a nominal voltage of 280 V or more but not more than 400 V, a nominal capacity of 9,7 Ah or more but not more than 10,35 Ah, a charging voltage of 110 V or more but not more than 230 V, and containing 6 modules with 90 cells or more but not more than 96 cells enclosed in a steel casing, for use in the manufacture of vehicle capable of being charged by plugging to external source of electric power of heading 8703 1,3 %-31.12.20240.8566ex8507600021 Cylindrical rechargeable lithium-ion polymer accumulator module with: a cable, a connector, 1 or 2 cells, a charge control module or NTC temperature sensor, a fuse, a weight of 37,3 g or more but not more than 91,5 g, a nominal voltage of 3,2 V, a battery capacity of 1100 mAh or more but not more than 2200 mAh, for the manufacture of automatic emergency call devices for passenger cars 1,3 %-31.12.2024 0.8593ex8507600024 Rechargeable lithium-ion battery, based on lithium-iron-phosphate technology, with: a fuse, a cell-to-pack design, a length of 985 mm or more but not more than 1015 mm, a width of 1050 mm or more but not more than 1070 mm a height of 145 mm or more but not more than 160 mm, a weight of 220 kg or more but not more than 250 kg, a capacity of 200 Ah or more, a specific energy density of 130 Wh/kg or more, for use in the manufacture of vehicles of subheading 870240 1,3 %-31.12.20240.8368ex8507600029 A lithium-ion-rechargeable battery pack in a specific housing suitable for operating in digital cameras, having: a length of 70 mm or more but not more than 120 mm, a width of 60 mm or more but not more than 80 mm,

a height of 15 mm or more but not more than 45 mm, a weight of 0,040 kg or more but not more than 0,085 kg, and a capacity of not more than 1860 mAh 1,3 %-31.12.20240.2907ex8507600030Cylindrical lithium-ion accumulator or module, with a length of 63 mm or more and a diameter of 17,2 mm or more, having a nominal capacity of 1200 mAh or more, for use in the manufacture of rechargeable batteries1,3 %-31.12.20240.6703ex8507600033 Lithium-ion accumulator, with: a length of 150 mm or more, but not more than 1310 mm, a width of 100 mm or more, but not more than 1000 mm, a height of 200 mm or more, but not more than 1500 mm, a weight of 75 kg or more, but not more than 200 kg, a nominal capacity not less than 58 Ah and not more than 500 Ah, a nominal output voltage of 230V AC (line to neutral) or a nominal voltage of 50V (± 10 %) 1,3 %-31.12.2024 0.6702ex8507600037 Lithium-ion accumulator, with: a length of 1200 mm or more, but not more than 2000 mm, a width of 800 mm or more, but not more than 1300 mm, a height of 2000 mm or more, but not more than 2800 mm, a weight of 1800 kg or more, but not more than 3000 kg, a nominal capacity of 2800 Ah or more but not more than 7200 Ah 1,3 %-31.12.20240.8115ex8507600048 Integrated battery system in a metal case with holders, consisting of: a lithium-ion battery with a voltage of 36 V or more but not more than 50,4 V and a nominal energy of 0,6 kWh, Battery Management System, a power relay, a cooling system, four connectors, for use in the manufacture of Mild-hybrid (mHEV) motor vehicles 1,3 %-31.12.20240.5548ex8507600050 Modules for the assembly of batteries of ion lithium electric accumulators with: a length of 298 mm or more, but not more than 500 mm, a width of 33,5 mm or more, but not more than 209 mm, a height of 75 mm or more, but not more than 228 mm, a weight of 3,6 kg or more, but not more than 17 kg, and a power of 458 Wh or more, but not more than 2900 Wh 1,3 %-31.12.20240.7641ex8507600058 Prismatic lithium-ion electric accumulator with: a width of 120,0 mm or more but not more than 305,0 mm, a thickness of 12,0 mm or more but not more than 67,0 mm, a height of 72,0 mm or more but not more than 126,0 mm, a nominal voltage of 3,6 V or more but not more than 3,75 V, and a nominal capacity of 6,9 Ah or more not more than 265 Ah, for use in the manufacture of rechargeable electric vehicle batteries 1,3 %-31.12.2024 0.5342ex8507600065 Cylindrical lithium ion cell with a nominal diameter of 9,8 mm or more, but not more than 14,5 mm, a nominal voltage of 3,0 VDC or more, but not more than 4,0 VDC, and a nominal capacity of 200 mAh or more, but not more than 1200 mAh 1,3 %-31.12.20240.7888ex8507600068 Lithium-ion accumulator in a metal housing, with a length of 65 mm or more, but not more than 225 mm, a width of 10 mm or more, but not more than 75 mm, a height of 60 mm or more, but not more than 285 mm, a nominal voltage of 2,1 V or more, but not more than 3,8 V, and a nominal capacity of 2,5 Ah or more, but not more than 325 Ah

1,3 %-31.12.20240.8259ex8507600073 Lithium-ion Electric accumulators consisting of 3 modules containing 102 cells in total, with: a nominal capacity of 51 Ah per cell, a nominal voltage of 285 V or more but not more than 426V, a weight of 33 kg or more but not more than 36 kg per module, a length of 1400 mm or more but not more than 1600 mm, a height of 340 mm or more but not more than 395 mm, a width of 220 mm or more but not more than 420 mm, for use in the manufacture of vehicles of subheadings 870360 and 870380 1,3 %-31.12.20240.6753ex8507600077 Lithium-ion rechargeable batteries, with: a length of 700 mm or more, but not more than 2820 mm, a width of 935 mm or more, but not more than 1660 mm, a height of 85 mm or more, but not more than 700 mm, a weight of 250 kg or more, but not more than 700 kg, a power of not more than 175 kWh, a nominal voltage of 350 V or more, but not more than 430 V 1,3 %-31.12.2024 0.8275ex8507600083 Modules for the assembly of ion lithium electric accumulators with: a length of 570 mm or more, but not more than 610 mm, a width of 210 mm or more, but not more than 240 mm, a height of 100 mm or more, but not more than 120 mm, a weight of 28 kg or more, but not more than 35 kg, and a capacity of not more than 2500 Ah and a nominal energy of less than 7,5 kW, for use in the manufacture of vehicles of subheadings 870360, 870370, 870380 and 870460 1,3 %-31.12.20240.8286ex8507600088 A rechargeable lithium-ion battery, with: a fuse, a cell-to-pack design, a length of 1050 mm or more but not more than 1070 mm, a width of 624 mm or more but not more than 636 mm, a height of 235 mm or more but not more than 245 mm, a mass of 214,4 kg or more but not more than 227,6 kg, a capacity of 228 Ah, an upper outer casing of a composite material, an IP68 protection rating, an energy density of 220Wh/l or more, a specific energy of 159 Wh/kg or more, without contactors, for the manufacture of batteries for electric buses 1,3 %-31.12.20240.8419ex8507908020 Top cap made of ferrous alloy or stainless steel: whether or not including parts made of aluminum and aluminum alloy, with sealing elements or other elements made of polymer material, with a current interrupt device and an evacuation valve, with an outer diameter of 17 mm or more, but not more than 18 mm, for use in the manufacture of lithium-ion batteries 1,3 %-31.12.2024 0.5014 ex85087000 ex85371098 20 98 Electronic circuit cards that: are connected by wire or radio frequency to each other and the motor controller card, and regulate the functioning (switching on or off and suction capacity) of vacuum cleaners according to a stored program, whether or not fitted with indicators that display the functioning of the vacuum cleaner (suction capacity and/or dust bag full and/or filter full) 0 %p/st31.12.20250.6304ex8511300030 Igniter integrated coil assembly with: an igniter, a coil on plug assembly with an integrated mounting bracket, a housing, a length of 90 mm or more but not more than 200 mm (± 5 mm),

an operating temperature of -40 °C or more but not more than 130 °C, a voltage of 10,5 V or more, but not more than 16 V 0 %p/st31.12.20240.7024ex8511300055 Ignition coil: with a length of 50 mm or more, but not more than 200 mm, with an operating temperature of – 40 °C or more, but not more than 140 °C, and with a voltage of 9 V or more, but not more than 16 V, with or without connection cable, for use in the manufacture of engines of motor vehicles 0 %-31.12.20260.6856ex8512200030 Lighting module, containing at least: two LEDs, glass or plastic lenses, focusing/scattering the light emitted by the LEDs, reflectors redirecting the light emitted by the LEDs, in an aluminium housing with a radiator, mounted at a bracket with an actuator 0 %p/st31.12.2025 0.6503ex8512200040 Fog lamp with a galvanised inner surface, containing: a plastic holder with three or more brackets, one or more 12 V bulbs, a connector, a plastic cover, whether or not with a connection cable for use in the manufacture of goods of Chapter 87 0 %p/st31.12.20240.6562ex8512200060 Information screen displaying: at least time, date and status of safety features in a vehicle, or safety information on driving in the lane, blind spot, distance from the vehicle in front, current speed, speed limit, with an operating voltage of 12 V or more but not more than 14,4 V, of a kind used in the manufacturing of goods of Chapter 87 0 %p/st31.12.20240.8409ex8512200070 Electrical component with light guide integrated with LED, for motor vehicles with: two parallel ribs in the front area with a distance between them of 1,4 mm or more but not more than 1,8 mm, four holes with the dimension of 7,3 mm or more but not more than 7,9 mm in the short direction of the guide, and a 3 pin connector, for use in the manufacture of automotive components 0 %-31.12.20270.8410ex8512200080 Grab handle light with integrated LED, for motor vehicles: a distance between integrated spring clip and surface of 0,85 mm or more but not more than 1,85 mm, a length of the housing to two front vertical ribs of 26,45 mm or more but not more than 26,75 mm, and four horizontal ribs where the distance on the lower area over the base radia between the two is 18,5 mm or more but not more than 18,7 mm, for use in the manufacture of automotive components 0 %-31.12.2027 0.6504ex8512309010 Horn assembly operating on piezomechanical principle for generating a specific sound signal, with a voltage of 12 V, comprising: coil, magnet, metal membrane, connector, holder of a kind used in the manufacture of goods of Chapter 87 0 %p/st31.12.20240.6863ex8512309020 Warning buzzer for parking sensor system in a plastic casing operating on the piezo-mechanic principle, containing: a printed circuit board, a connector, whether or not a metal holder, for use in the manufacture of goods of chapter 87 0 %p/st31.12.20240.7361ex8512309030 Sound alarm device for protection against burglary into the vehicle: with an operating temperature of – 45 °C or more, but not more than + 95 °C,

with a voltage of 9 V or more but not more than 16 V, in a plastic housing, whether or not with a metal holder for use in the manufacture of motor vehicles 0 %-31.12.20240.8453ex8512309040 Device for simulating engine sound at reduced speed of a hybrid or electric vehicle: containing at least printed circuit board and loudspeaker, in a plastic housing with a holder, for use in the manufacture of goods of Chapter 87 0 %-31.12.20270.5983 ex85124000 ex85168020 10 20 Car door mirror heating foil: with two electrical contacts, with an adhesive layer on both sides (on the side of the plastic holder of the mirror and on the side of the mirror glass), with a protective paper film on both sides 0 %-31.12.2024 0.6522 ex85142080 ex85165000 ex85166080 10 10 10 Cavity assembly comprising at least: a transformer with an input of not more than 240 V and an output of not more than 3000 W an AC or DC fan motor with an output of not more than 42 W a housing made of stainless steel with or without a magnetron of a microwave output power of not more than 900 W for use in the manufacture of built-in products of subheadings 85142080, 85165000 and 85166080 0 %p/st31.12.20240.8391ex8516108010 Tubular Heating Element with mounting flange for washing machines, with: a nominal output power of 1700 W at 230 V AC supply voltage, a weight of 230 g or more but not more than 250 g, a thickness of the external flange of 2 mm or more, isolation bushes of steatite or ceramic, and no flat zones in the design, for use in the manufacture of home appliance products and their components 0 %p/st31.12.20270.4732ex8516900060 Ventilation sub-assembly of an electric deep-fat fryer: fitted with a motor having a power rating of 8 W at 4600 rpm, governed by an electronic circuit, operating at ambient temperatures above 110 °C, fitted with a thermoregulator 0 %p/st31.12.20240.5845ex8516900070 Inner pot: containing side and central openings, of annealed aluminium, with a ceramic coating, heat resistant to more than 200° C for use in the manufacture of an electric fryer 0 %p/st31.12.20270.6521ex8516900080Door assembly incorporating a capacitive sealing element and wavelength choke for use in the manufacture of built-in products of subheadings 85142080, 85165000 and 851660800 %p/st31.12.2024 0.6316ex8528590020 Liquid crystal display colour video monitor assembly mounted on a frame, excluding those combined with other apparatus, comprising touch screen facilities, a printed circuit board with drive circuitry and power supply, used for permanent incorporation or permanent mounting into entertainment systems for vehicles 0 %-31.12.20240.7048ex8536411020Photoelectric (so called photovoltaic) relay consisting of a GaAlAs light-emitting diode, a galvanically isolated input circuit with a photovoltaic generator and a power MOSFET output switch in a casing with connections for a voltage of 60 volts or less and a current of 2 amps or less0 %-31.12.20260.6180ex8536419040 Power relay with: electromechanical and/or electromagnetical switching function,

a load current of 3 A or more but not more than 16 A, a coil voltage of 5 V or more but not more than 24 V, and a distance between the connector pins of the load circuit not more than 15,6 mm 0 %p/st31.12.20240.7052ex8536490040Photoelectric (so called photovoltaic) relay consisting of two GaAlAs light-emitting diodes, two galvanically isolated input circuits with photovoltaic generator(s) and four power MOSFET output switches in a casing with connections for a voltage of more than 60 volts0 %-31.12.20260.7796ex8536490060 Relay in the shape of a cube with: a coil operating voltage of 12 VDC (Voltage Direct Current) or more, but not more than 24 VDC (Voltage Direct Current), a contact current carrying capacity of 5A or more, but not more than 15A, a contact voltage of 80 VAC (Voltage Alternating Current) or more, but not more than 270 VAC (Voltage Alternating Current), outer dimensions of 19 mm (± 0,4 mm) x 15,2 mm (± 0,4 mm) x 15,5 mm (± 0,4 mm), for use in the production of control board of household appliances 0 %-31.12.2024 0.4614ex8536699082 Modular socket or plug for local area networks, whether or not combined with other sockets, integrating at least: a pulse transformer, including a wide-band ferrite core, a common mode coil, a resistor, a capacitor, for use in the manufacture of products falling within headings 8521 or 8528 0 %p/st31.12.20240.4616ex8536699083 AC socket with a noise filter, composed of: AC socket (for power cord connection) of 230 V, integrated noise filter composed of capacitors and inductors, cable connector for connecting an AC socket with the PDP (Plasma display panel) power supply unit, whether or not equipped with a metal support, which joins the AC socket to the PDP TV set 0 %p/st31.12.20240.5028ex8536699084Universal serial bus (USB) socket or plug in a single or multiple form for connecting with other USB devices, for use in the manufacture of goods falling within headings 8521 or 85280 %p/st31.12.20250.5318ex8536699085Socket or plug, built into a plastic or metal housing, with no more than 96 pins, for use in the manufacture of products falling within headings 8521 or 85280 %p/st31.12.20260.5316ex8536699086High-Definition Multimedia Interface (HDMI) type socket or plug, built into a plastic or metal housing, with 19 pins or 20 pins in 2 rows, for use in the manufacture of products falling within headings 8521 or 85280 %p/st31.12.20260.5181ex8536700010Optical socket, plug or connector, for use in the manufacture of goods falling within headings 8521 or 85280 %p/st31.12.20260.7873ex8537109120 Electronic assembly containing: a microprocessor, a programmable memory and other electronic components mounted on a printed circuit, with or without light-emitting diode (LED) or liquid crystal display (LCD) indicators, for use in the manufacture of products of subheadings 841821, 841829, 842112, 842211, 845011, 845012, 845019, 845121, 845129 and 851660 0 %-31.12.2024 0.8405ex8537109125 A control unit being a printed circuit board with at least:

a microprocessor, a programmable memory, a single connector, a PPE housing, a supply of voltage of 220 V or more but not more than 240 V, a length of 200 mm or more but not more than 210 mm, a width of 70 mm or more but not more than 100 mm, and a height of 20 mm or more but not more than 30 mm, for use in the manufacture of dishwashers 0 %-31.12.20270.8392ex8537109135 A control unit being a printed circuit board with at least: a microprocessor, a programmable memory, two or more connectors, but not more than twelve, with or without LCD display, with or without WiFi module, and with or without an integrated speaker, for use in the manufacture of built-in ovens 0 %-31.12.20270.8460ex8537109143 Electronic suspension control unit with: a printed circuit board in plastic housing, LIN and CAN buses, a programmable memory, a signal processor, an operating direct current voltage of 9 V or more but not more than 16 V, at least one connector, whether or not with metal mounting bracket, for use in the manufacture of goods of Chapter 87 0 %-31.12.20270.8085ex8537109145 Main hybrid system controller, diagnosing and controlling the elements of the hybrid propulsion system, with: a programmable memory, a microprocessor, at least one composite connector, a voltage of 24 V, with a length of 350 mm or more but not more than 400 mm, with a width of 200 mm or more but not more than 250 mm, with a height of 80 mm or more but not more than 120 mm, in a metal housing 0 %-31.12.2025 0.6864ex8537109150 Fuse control module in a plastic housing with mounting brackets comprising: sockets with or without fuses, connecting ports, a printed circuit board with embedded microprocessor, micro switch and relay, of a kind used in the manufacture of goods of chapter 87 0 %p/st31.12.20250.7627ex8537109157 Programmable memory control board with: 4 or more stepper motor drivers, 4 or more outputs with MOSFET transistors, a main processor, 3 or more inputs for temperature sensors, for a voltage of 10 V or more but not more than 30 V, for use in the manufacture of 3D printers 0 %-31.12.20240.7609ex8537109159 Electronic control units for controlling inter axle torque transferring in all-wheel drive vehicles including: a printed circuit board with programmable memory controller, one single connector, and working at 12 V 0 %-31.12.20240.6163 ex85371091 ex85371098 60 45 Electronic control units, manufactured according to class 2 of IPC-A-610E standard, with at least: an AC power input of 208 V or more but not more than 400 V, a logic power input of 24 V DC, an automatic circuit breaker, a main power switch, internal or external electrical connectors and cables, in a housing with dimension of 281 mm x 180 mm x 75 mm or more, but not more than 630 mm x 420 mm x 230 mm, of a kind used for manufacturing recycling or sorting machines 0 %p/st31.12.2024 0.7610ex8537109163 Electronic control units able to control automatic continuous variable transmission for passenger vehicles including: a printed circuit board with programmable memory controller,

a metallic housing, one single connector, working at 12V 0 %-31.12.20240.7660ex8537109167 Electronic Engine Control Unit (ECU) with: a printed circuit board (PCB), 12 Volts voltage, reprogrammable, a micro-processor that can control, evaluate and manage support service functions in cars (injection and ignition advance values of fuel, fuel and air flow rate), for use in the manufacture of goods of Chapter 87 0 %-31.12.20240.7251ex8537109170 Programmable motor memory controller for a voltage not exceeding 1000 V, comprising at least: a printed circuit with active and passive components, an aluminium housing, and multiple connectors 0 %p/st31.12.20270.6140ex8537109830 Motor bridge ICs without programmable memory consisting of: one or more integrated circuits, not interconnected, on separate lead frames, also with discrete Metal Oxide Field Effect Transistors (MOSFET) for controlling DC motors in cars mounted in a plastic housing 0 %p/st31.12.20240.7194ex8537109833 Lever for control module under the steering wheel: with several single or multi-positional electrical switches (push-button, rotary or other), equipped with printed circuit boards and/or electrical cables, for a voltage of 9 V or more but not more than 16 V, of a kind used in the manufacture of motor vehicles of Chapter 87 0 %p/st31.12.2026 0.6889ex8537109835 Electronic control unit without memory, for a voltage of 12 V, for information exchange systems in vehicles (for connection of audio, telephony, navigation, camera and wireless car service) containing: 2 rotary knobs 27 or more pushbuttons LED lights 2 integrated circuits for receiving and sending of control signals via the LIN-bus 0 %p/st31.12.20250.8401ex8537109838 Control panel with switches for mirror, windows and other functions in vehicles, with: a total length of 144 mm or more but not more than 150 mm, a distance between intended screwing interface center points of 31 mm or more but not more than 31,50 mm, and electric components inside the panel with integrated LEDs, for use in the manufacture of automotive components 0 %-31.12.20270.6508ex8537109840 Electronic control unit for monitoring car vehicle tyre pressure comprising plastic box with printed circuit board inside and with or without metal holder, of: a length of 50 mm or more, but not more than 120 mm, a width of 20 mm or more but not more than 40 mm, a height of 30 mm or more, but not more than 120 mm, of a kind used in the manufacture of goods of Chapter 87 0 %p/st31.12.20240.8408ex8537109843 Switch for motor vehicle seat regulation with a memory function, with: three single switches, a five-pin connector, for a voltage of 9 VDC or more but not more than 16 VDC, and electric components inside the panel with integrated LED, for use in the manufacture of automotive components 0 %-31.12.2027 0.8400ex8537109848 Memory switch control panel for seat and lock switch for vehicles with: a width of 70,2 mm or more but not more than 70,5 mm, parallel ribs with a distance between them of 2,6 mm or more but not more than 2,8 mm on the rear side,

a 5 pin connector, and electric components inside the panel with integrated LED, for use in the manufacture of automotive components 0 %-31.12.20270.6507ex8537109850 Electronic control unit BCM (Body Control Module) or IBM (Integrated Body Control Module) or similar: comprising at least a plastic box with printed circuit board, with operating direct voltage of 9 V or more, but not more than 16 V, whether or not with metal holder, able to control, evaluate and manage functions of assisting services in an automobile, at least wiper timing, window heating, interior lighting, seat belt reminder, of a kind used in the manufacture of goods of Chapter 87 0 %p/st31.12.20240.8407ex8537109853 A control unit being a printed circuit board with at least: a microprocessor, two or more connectors but not more than four, modified resins, a length of 180 mm or more but not more than 250 mm, a width of 130 mm or more but not more than 200 mm, and a height of 40 mm or more but not more than 60 mm, for use in the manufacture of washing machines 0 %-31.12.20270.8393ex8537109857 A control unit being a printed circuit board with at least: a microprocessor, eight connectors or more but not more than eleven, a supply voltage of 215 V or more but not more than 245 V, a housing of PA6-MR30, with or without a transformer, with or without a high power relay, with or without insulated-gate bipolar transistor, a length of 280 mm or more but not more than 345 mm, a width of 400 mm or more but not more than 470 mm, a height of 28 mm or more but not more than 45 mm, for use in the manufacture of induction stoves 0 %-31.12.2027 0.6520ex8537109860 Electronic assembly consisting of: a microprocessor, light-emitting diode (LED) or liquid crystal display (LCD) indicators, electronic components mounted on a printed circuit, for use in the manufacture of built-in products of subheadings 85142080, 85165000 and 85166080 0 %p/st31.12.20240.8406ex8537109863 A control unit being a printed circuit board with at least: a microprocessor, two connectors, a supply voltage of 215 V or more but not more than 245 V, no housing, a length of 100 mm or more but not more than 120 mm, a width of 40 mm or more but not more than 50 mm, and a height of 20 mm or more but not more than 30 mm, for use in the manufacture of refrigerators 0 %-31.12.20270.7171ex8537109875 Control unit for keyless access to vehicle and vehicle starting, with electrical switching apparatus, in a plastic housing, for a voltage of 12 V, whether or not with: an antenna, a connector, a metal holder, for use in the manufacture of goods of Chapter 87 0 %p/st31.12.20240.8132ex8537109880 Propulsion Control System with at least: a DC/AC inverter, a power of 190 kW or more but not more than 220 kW, a high voltage circuits with AC and DC interfaces for connecting a traction motor, generator and energy storage system, an integral control of all drive motor and generator traction system functions, a CAN communications interface with System Control Unit,

a liquid cooled system, a length of 300 mm or more but not more than 950 mm, a width of 350 mm or more but not more than 600 mm, a height of 200 mm or more but not more than 350 mm, a weight of 40 kg or more but not more than 90 kg 0 %p/st31.12.2025 0.8124ex8537109888 Control panel for car radio and/or navigation control and/or climate unit and heater unit control with: electronic passive components, at least two switches, LEDs, at least one connector, whether or not warning triangle switch, for a voltage not exceeding 16 V, for use in the manufacture of goods of Chapter 87 0 %-31.12.20250.3663ex8537109893Electronic control units for a voltage of 12 V, for use in the manufacture of vehicle mounted temperature control systems0 %p/st31.12.20240.6866 ex85389091 ex85389099 20 50 Interior antenna for a car door locking system, comprising: an antenna module in a plastic housing, whether or not a connection cable with a plug, whether or not a connector, at least one mounting bracket, whether or not PCB including integrated circuits, diodes and transistors, for use in the manufacture of goods of Chapter 87 0 %p/st31.12.20250.6397 ex85389099 ex85472000 30 10 Polycarbonate or acrylonitrile butadiene styrene covers and cases for steering pad switches whether or not coated on the outside with a scratch resistant paint0 %p/st31.12.20240.6399ex8538909940Polycarbonate control interface buttons for steering pad switches coated on the outside with scratch resistant paint, in immediate packages of 500 pieces or more0 %p/st31.12.20240.7195ex8538909960Front control panel, in the form of a plastic box, with light guides, rotary switches, pressure switches and buttons switches, or other type of switches, without any electrical component, of a kind used in the dashboard of motor vehicles of Chapter 870 %p/st31.12.20260.2580ex8540208091Photomultiplier0 %-31.12.2026 0.3959ex8540710020 Continuous wave magnetron with: a fixed frequency of 2460 MHz, a packaged magnet, a probe output, an output power of 960 or more but not more than 1500 W 0 %-31.12.20240.3445ex8540890091Displays in the form of a tube consisting of a glass housing mounted on a board the dimensions of which do not exceed 300 mm × 350 mm excluding leads. The tube contains one or more rows of characters or lines arranged in rows, each character or line consisting of fluorescent or phosphorescent elements. These elements are mounted on a metallised base which is covered with fluorescent substances or phosphorescent salts which give off light when bombarded with electrons0 %-31.12.20240.3443ex8540890092Vacuum fluorescent display tube0 %-31.12.20240.7409ex8540910020 Thermionic electron source (emitter point) of lanthanum hexaboride (CAS RN 12008-21-8) or cerium hexaboride (CAS RN 12008-02-5), with electric connectors with or without a metal housing, with or without a graphite carbon shield mounted in a mini-Vogel type system, with or without separate pyrolytic carbon blocks used as heating elements, and a cathode temperature of less than 1800 K at a filament current of 1,26 A

0 %-31.12.20270.7130ex8543709015 Laminated electrochromic film consisting of: two outer layers of polyester, a middle layer of acrylic polymer and silicone, and two electric connection terminals 0 %-31.12.20260.8333ex8543709027 Electronic control unit of the 360-degree vehicle situation display system with: an operating DC voltage of 9 V or more but not more than 16 V, a videoprocessor, a signal processor, one or more connectors, and whether or not with a metal mounting bracket, for use in the manufacture of goods of Chapter 87 0 %-31.12.2027 0.2826ex8543709030Amplifier, consisting of active and passive elements mounted on a printed circuit, contained in a housing0 %p/st31.12.20240.7055ex8543709033High-frequency amplifier comprising one or more integrated circuits and one or more discrete capacitor chips, whether or not with IPD (integrated passive devices) on a metal flange in a housing0 %-31.12.20260.2822ex8543709035Radio frequency (RF) modulator, operating with a frequency range of 43 MHz or more but not more than 870 MHz, capable of switching VHF and UHF signals, consisting of active and passive elements mounted on a printed circuit, contained in a housing0 %p/st31.12.20240.2590ex8543709045Piezo-electric crystal oscillator with a fixed frequency, within a frequency range of 1,8 MHz to 67 MHz, contained in a housing0 %p/st31.12.20240.3131ex8543709055Opto-electronic circuit comprising one or more light-emitting diodes (LEDs), whether or not equipped with an integrated driving circuit, and one photodiode with amplifier circuit, whether or not with an integrated logic gate arrays circuit or one or more light-emitting diodes and at least 2 photodiodes with an amplifier circuit, whether or not with an integrated logic gate arrays circuit or other integrated circuits, contained in a housing0 %p/st31.12.20240.2820ex8543709080Temperature compensated oscillator, comprising a printed circuit on which are mounted at least a piezo-electric crystal and an adjustable capacitor, contained in a housing0 %p/st31.12.20240.2816ex8543709085Voltage controlled oscillator (VCO), other than temperature compensated oscillators, consisting of active and passive elements mounted on a printed circuit, contained in a housing0 %p/st31.12.20240.6709ex8544200030 Antenna connecting cable for the transmission of radio (AM/FM) signal and whether or not GPS signal, containing: a coaxial cable, two or more connectors, and 3 or more plastic clips for attachment to the dashboard of a kind used in the manufacture of goods of Chapter 87 0 %-31.12.2026 0.6194ex8544300030 Multi-measurement wire harness of a voltage of 5V or more but not more than 90 V capable of measuring some or all of the following; a travel speed of not more than 24 km/h a motor speed of not more than 4500 rpm hydraulic pressure of not more than 25 Mpa mass of not more than 50 metric tonnes for use in the manufacture of vehicles of heading 8427 0 %p/st31.12.20240.6377 ex85443000 ex85444290 40 40 Wire harness or cable for steering system:

for an operating voltage of 12 V, with connectors on both sides, whether or not with anchor clamps of plastic for mounting on a motor vehicle steering box 0 %p/st31.12.20240.7848ex8544300045Linking seven-core cable for connecting sensor for pressure measure in intake manifold (Boost Pressure Sensor - BPS) and sockets for glow plugs with common connector, containing four sockets and two connectors for use in the manufacture of compression-ignition internal combustion piston engines for passenger cars0 %-31.12.20240.7847ex8544300055Connecting five-core cable with connectors for coupling the temperature sensor and the exhaust manifold pressure difference sensor to the common connector for use in the manufacture of compression-ignition internal combustion piston engines of passenger cars0 %-31.12.20240.6710 ex85443000 ex85444290 60 50 Four-core connecting cable containing two female connectors for the transmission of digital signals from navigation and audio systems to a USB connector, for use in the manufacture of goods of Chapter 870 %-31.12.20250.8331ex8544300065 Six core cable connecting the oil pressure sensor and the differential controller of vehicles: with PVC-coating, with three multiple connectors, and with or without plastic clip, for use in the manufacture of goods of Chapter 87 0 %-31.12.2027 0.6323ex8544300070 Multi-measurement wire harness: of a voltage of 5 V or more but not more than 90 V, capable of transmitting information for use in the manufacture of vehicles of heading 8711 0 %p/st31.12.20240.6867ex8544300085 Extension two-core cable with two connectors, containing at least: a rubber grommet, a metal attachment bracket, of a kind used to connect vehicle speed sensors in the manufacture of vehicles of Chapter 87 0 %p/st31.12.20250.4980ex8544429010 Data transmission cable capable of a bit rate transmission of 600 Mbit/s or more, with: a voltage of 1,25 V (± 0,25 V) connectors fitted at one or both ends, at least one of which contains pins with a pitch of 1 mm, outer screening shielding, used solely for communication between LCD, PDP or OLED panel and video processing electronic circuits 0 %p/st31.12.20240.7545ex8544429015 PVC isolated flexible eight wire cable with: a length of not more than 2100 mm an operating voltage of 5V or more, but not more than 35V a temperature resistance of not more than 80°C either an over-moulded 7 pin round 270 DIN male connector, a 6 pin A1101 male connector or a 8 pin A1001 male connector on one end and at least two stripped and tinned wires on the other end whether or not with mounted rubber pad with integrated strain relief 0 %-31.12.2024 0.4464 ex85444290 ex85444993 ex85444995 20 20 10 PET or PVC insulated flexible cable with or without connector with: voltage of not more than 250 V, a current of not more than 1 A, a heat resistance of not more than 105 °C, individual wires of a thickness of not more than 0,1 mm (± 0,01 mm) and a width of not more than 0,8 mm (± 0,03 mm), a distance between conductors of not more than 0,5 mm and

a pitch (distance from centreline to centreline of conductors) of not more than 1,25 mm 0 %-31.12.20280.7538ex8544429025 PVC isolated flexible cable with: a length of not more than 1800 mm an operating voltage of 5V or more, but not more than 35V a heat resistance of not more than 80°C an over-moulded 8 pin MiniFit male connector on one end either a 6 pin MiniFit socket or two over-moulded AMP connectors on the other end a over-moulded resistor inside the connector and a moulded strain relief on the cable whether or not with a over-moulded diode inside a connector 0 %-31.12.20240.7544ex8544429035 PVC isolated flexible six or eight wire cable with: a length of not more than 1300 mm an operating voltage of 5V or more, but not more than 35V a heat resistance of not more than 80°C either an over-moulded 8 pin MiniFit male connector or an over-moulded 6-pin DIN male connector on one end and either an over-moulded 8 pin MiniFit socket or an 8 pin MicroFit male connector on the other end 0 %-31.12.2024 0.8572 ex85444290 ex85446010 45 10 Specially designed connector for solar power system: as 1-part system with 1 plastic housing with 1 or more but not more than 4 diodes and 2 insulated copper cables with connectors or as 3-part system with one plastic housing with 1 or more but not more than 4 diodes and 2 plastic housings with insulated copper cables with connectors, with a current for the diodes of 3 A or more but not more of 50 A, with a cable length of not more than 1500 mm, with a maximum rated voltage of 1500 V 0 %-31.12.20280.6853ex8544429070 Electric conductors: of a voltage of not more than 80 V, with a length of not more than 120 cm, fitted with connectors, for use in the manufacture of hearing aids, accessory kits and speech processors 0 %p/st31.12.20250.7173ex8544429080 12-wire connecting cable containing two connectors of a voltage of 5 V, with a length of not more than 300 mm for use in the manufacture of goods of Chapter 87 0 %p/st31.12.20240.2424ex8544499310Elastomeric connector, of rubber or silicone, consisting of one or more conductor elements0 %p/st31.12.20240.6861ex8544499330 Electric conductors: of a voltage of not more than 80 V, of a platinum-iridium-alloy, coated with poly(tetrafluoroethylene), without connectors, for use in the manufacture of hearing aids, implants and speech processors 0 %m31.12.20250.3144ex8548009041Unit, consisting of a resonator operating within a frequency range of 1,8 MHz or more but not more than 40 MHz and a capacitor, contained in a housing0 %p/st31.12.2024 0.3193ex8548009043Contact image sensor0 %p/st31.12.20240.2434ex8548009044Parts of TV-apparatus, having micro-processor and video-processor functions, comprising at least a micro-controller and a video-processor, mounted on a leadframe and contained in a plastic housing0 %p/st31.12.20240.3763ex8548009048 Optical unit, containing at least a laser diode and a photodiode operating at a typical wavelength of 635 nm or more but not more than 815 nm an optical lens

a Recording Photodetector Integrated Circuit (PDIC) a focussing and tracking actuator 0 %p/st31.12.20260.5183 ex85491320 ex85491420 10 10 Spent lithium-ion or nickel metal hydride electric accumulators0 %-31.12.20240.7165 ex87081010 ex87081090 10 10 Plastic cover for filling the space between the fog lights and the bumper whether or not with a chrome strip for use in the manufacture of goods of Chapter 870 %p/st31.12.20260.6513 ex87083010 ex87083091 ex87083099 20 60 10 Motor powered brake actuation unit with a rating of 13.5 V (±0.5V) and a ball screw mechanism to control brake fluid pressure in the master cylinder for use in the manufacture of electric motor vehicles 0 %p/st31.12.20240.6590 ex87083010 ex87083091 40 30 Body of disc type brake in BIR (Ball in Ramp) or EPB (Electronic Parking Brake) or with hydraulic function only, containing functional and mounting openings and guide grooves, of a kind used in the manufacture of goods of Chapter 870 %p/st31.12.20240.6502 ex87083010 ex87083091 60 20 Non-asbestos organic brake pads with friction material mounted to the band steel back plate for use in the manufacture of goods of Chapter 870 %p/st31.12.20240.6707 ex87083010 ex87083091 70 40 Ductile cast iron brake caliper jaw, of a kind used in the manufacture of goods of Chapter 870 %p/st31.12.2025 0.6869 ex87084020 ex87084050 20 10 Automatic hydrodynamic gearbox with a hydraulic torque converter, without transfer box and cardan shaft, whether or not with front differential, for use in the manufacture of motor vehicles of Chapter 87 0 %p/st31.12.20250.7383 ex87084020 ex87084050 50 40 Transmission assembly which houses 3 other shafts inside it and offers a rotating switch for shift position consisting: cast aluminium body, differential gear, 2 electrical motors and gears, with the dimensions of: a width of 280 mm or more but not more than 470 mm, a height of 350 mm or more but not more than 595 mm, a length of 410 mm or more but not more than 690 mm, for use in the manufacture of motor vehicles of Chapter 87 0 %-31.12.20240.7655 ex87084020 ex87084050 60 50 Automatic transmission assembly with rotary gear shifter with: aluminium casting housing, differential gear, 9 Speed automatic, electronic range select gear selection system, with dimensions of: a width of 330 mm or more but not more than 420 mm, a height of 380 mm or more but not more than 450 mm, a length of 580 mm or more but not more than 690 mm, for use in the manufacture of the vehicles of Chapter 87 0 %-31.12.20240.7856 ex87084020 ex87084050 70 60 Manual gearbox in cast aluminium housing for transverse installation with: a width of not more than 480 mm, a height of not more than 400 mm, a length of not more than 550 mm, five or six gears, a differential gear, an engine torque of 400 Nm or less, for use in the manufacture of motor vehicles of Heading 8703 0 %-31.12.2024 0.8279ex8708402080 Transmission gearbox without torque converter, with: dual clutch, 7 or more forward gears, 1 reverse gear,

a maximum torque of 390 Nm, whether or not with electric motor integrated, a height of 400 mm or more but not more than 600 mm, a width 350 mm or more but not more than 600 mm, and a weight of 70 kg or more but not more than 110 kg, for use in the manufacture of motor vehicles of Heading 8703 0 %p/st31.12.20260.8377ex8708405070 Automatic transmission equipped with double clutch system with: at least 8 gears, an engine torque of 800 Nm or more, an electronic differential, a P-lock safety system, and a TCU transmission control unit, for use in the manufacture of motor vehicles of heading 8703 0 %-31.12.20270.7987 ex87085020 ex87085055 15 50 Spherical outboard constant velocity joint ball bearing cage, part of the vehicle’s drive system, made of material suitable to be carburized with a carbon content of 0,14 % or more but not more than 0,57 %, forged, turned, punched, milled and hardened0 %-31.12.20250.8461ex8708502018 Propeller shaft for torque transmission from the gearbox to the rear axle, consisting of: two cardan rods, central universal joint, central bearing with suspension in a plastic cover, universal joints on both ends of the shaft, slip, tube and end yokes, of a length of 1,4 m or more but not more than 2,4 m, for use in the production of goods of Chapter 87 0 %-31.12.2027 0.6648 ex87085020 ex87085099 20 10 Transmission shaft in carbon fibre reinforced plastics consisting of a unique piece without any joint in the middle of a length of 1 m or more but not more than 2 m, of a weight of 6 kg or more but not more than 9 kg 0 %p/st31.12.20250.7988 ex87085020 ex87085099 25 45 Ball-type outboard constant velocity joint housing for transmitting a torque from the engine and transmission to the wheels of motor vehicles, in a form of an outer race, with: 6 ball tracks or more but not more than 8, with a thread, an external involute spline with 21 or more but not more than 38 teeth, for running with bearing balls made of steel with a carbon content of 0,48 % or more but not more than 0,57 %, forged, turned, milled and hardened 0 %-31.12.20250.7989 ex87085020 ex87085099 35 50 Inboard constant velocity joint tripod housing, with: an outer diameter of 67,0 mm or more but not more than 99,0 mm, 3 cold calibrated roller tracks with a diameter of 29,95 mm or more but not more than 49,2 mm, an external spline with 21 teeth or more but not more than 41, forged, turned, rolled and hardened 0 %-31.12.20250.7990 ex87085020 ex87085099 45 55 Outboard constant velocity joint inner race, part of the vehicle’s drive system, with: 6 or more but not more than 8 ball tracks, suitable for bearing balls with a diameter of 12,0 mm or more but not more than 24,0 mm, forged, turned, milled, broached and hardened 0 %-31.12.20250.7359 ex87085020 ex87085055 ex87085091 ex87085099 50 20 10 40 Double flange bearing of 3rd generation, for motor vehicles, with double-row ball bearing, whether or not with impulse (encoder) ring, whether or not with antilock brake system (ABS) sensor,

whether or not with mounted screws, for use in the manufacture of goods of chapter 87 0 %-31.12.2027 0.7991 ex87085020 ex87085099 55 60 Inboard constant velocity joint tripod spider, part of the vehicle’s drive system, with: 3 trunnions with a diameter of 17,128 mm or more but not more than 25,468 mm, forged, turned, broached and hardened 0 %-31.12.20250.7581 ex87085020 ex87085099 60 15 Car transfer case with single input, dual output, to distribute torque between front and rear axles in an aluminium housing, with dimension of not more than 565 × 570 × 510 mm, comprising: at least an actuator, whether or not an interior distribution by chain 0 %-31.12.20240.7692 ex87085020 ex87085099 65 20 Intermediate steel shaft connecting the gearbox with semi-axle with: a length of 300 mm or more but not more than 650 mm, a spline end on both sides, whether or not with a pressed bearing in the case, whether or not with a holder, for use in the manufacture of goods of Chapter 87 0 %-31.12.20240.7593 ex87085020 ex87085099 70 25 Housing of tripod type half shaft inboard joint for transmitting a torque from engine and transmission to wheels of motor vehicles with: an outer diameter of 67,0 mm or more but not more than 84,5 mm, 3 cold calibrated roller tracks with a diameter of 29,90 mm or more but not more than 36,60 mm, sealing diameter 34,0 mm or more but not more than 41,0 mm, without lead angle, spline with 21 teeth or more but not more than 35, bearing seat diameter of 25,0 mm or more but not more than 30,0 mm, with or without oil grooves 0 %-31.12.2024 0.7640 ex87085020 ex87085099 75 35 Outboard joint assembly for transmitting a torque from engine and transmission to wheels of motor vehicles, consisting of: an inner race with 6 ball tracks for running with the bearing balls with a diameter 15,0 mm or more but not more than 20,0 mm, an outer race with 6 ball tracks for running with 6 bearing balls, made of steel with carbon content of 0,45 % or more but not more than 0,58 %, with thread and with a spline with 26 teeth or more but not more than 38, a spherical cage keeping bearing balls in the ball tracks of outer race and inner race in proper angular position, made of material suitable for carburizing with carbon content of 0,14 % or more but not more than 0,25 %, and with a grease compartment, capable of working at constant speed at variable articulation angle not higher than 50 degrees 0 %-31.12.20240.6711 ex87088020 ex87088035 10 10 Upper strut insulator containing: a metal holder with three mounting screws, and a rubber bump, for use in the manufacture of goods of Chapter 87 0 %p/st31.12.20250.7607ex8708809920 Aluminium suspension link arm, with dimensions of: a height of 50 mm or more but not more than 150 mm, a width of 10 mm or more but not more than 100 mm, a length of 100 mm or more but not more than 600 mm, a mass of 1000 g or more but not more than 3000 g, equipped with at least two bushed holes made of aluminium alloy with the following characteristics:

a tensile strength of 200 MPa or more, a strength of 19 kN or more, a stiffness of 5 kN/mm or more but not more than 9 kN/mm, a frequency of 400 Hz or more but not more than 600 Hz 0 %p/st31.12.20240.7365ex8708809930 Surface-hardened, steel piston rod for a hydraulic or hydropneumatic shock absorber of motor vehicles: with a chrome coating, of a diameter of 11 mm or more, but not more than 28 mm, of a length of 80 mm or more, but not more than 600 mm, with a threaded end or a mandrel for resistance welding 0 %-31.12.2027 0.6509 ex87089120 ex87089135 20 10 Aluminium cooler using compressed air with a ribbed design of a kind used in the manufacture of goods of Chapter 870 %p/st31.12.20240.6859 ex87089120 ex87089199 30 30 Aluminium alloy inlet or outlet air tank of heat exchangers for car cooling systems, manufactured to standard EN AC 42100 or EN AC 43000 T6 with: an insulating area flatness of not more than 0,1 mm, a permissible particle quantity of 0,3 mg per tank, a distance between pores of 2 mm or more, pore sizes of not more than 0,4 mm, and not more than 3 pores larger than 0,2mm, with a weight of 0,2 kg or more but not more than 3 kg 0 %p/st31.12.20250.7716ex8708913520 Turbocharger cooling duct containing: an aluminum alloy duct with at least one metal holder and at least two mounting holes, a rubber pipe with clips, a stainless steel flange highly resistant to corrosion [SUS430JIL], for use in the manufacture of compression ignition engines of motor vehicles 0 %-31.12.20240.8538ex8708913530 Two-circuit aluminum heat exchanger for automatic transmission of passenger cars: of the stack-plate type, with two pairs of inlet and outlet, each for the coolant/water circuit and the transmission oil circuit, with at least two mounting holes, whether or not with the connection hoses, for use in the manufacture of goods of Chapter 87 0 %-31.12.20280.7231 ex87089199 ex87089997 40 55 Assembly for supplying compressed air, whether or not with a resonator, comprising at least: one solid aluminium tube whether or not with mounting bracket, one flexible rubber hose, and one metal clip for use in the manufacture of goods of Chapter 87 0 %-31.12.2024 0.7665ex8708929910 Exhaust system inner liner: with a wall thickness of 0,7 mm or more but not more than 1,3 mm, made of stainless steel sheets or coil class 1.4310 and 1.4301 according to norm EN 10088, whether or not with mounting holes, for use in the manufacture of exhaust systems for automobiles 0 %-31.12.20240.7664ex8708929920 Pipe for guiding exhaust gases from the combustion engine: with a diameter of 40 mm or more but not more than 100 mm, with a length of 90 mm or more but not more than 410 mm, with a wall thickness of 0,7 mm or more but not more than 1,3 mm, of stainless steel, for use in the manufacture of exhaust systems for automobiles 0 %-31.12.20240.7696ex8708929930 Exhaust system end cover: with a wall thickness of 0,7 mm or more but not more than 1,3 mm, made of stainless steel class 1.4310 and 1.4301 according to norm EN 10088,

whether or not with inner liner, whether or not with surface treatment, for use in the manufacture of exhaust systems for automobiles 0 %-31.12.20240.7849 ex87089310 ex87089390 40 40 Clutch pedal with electronic parking brake connection (EPB), whether or not with sending signal function for: cruise control reset, electronic parking brake release, start and stop engine management under Idle Stop and Go system (ISG), for use in the manufacture of passenger vehicles 0 %-31.12.20240.6526 ex87089420 ex87089435 10 20 Rack steering gear in aluminium housing with inner tie rod joints (axial joints) or with tie rods for use in the manufacture of goods of Chapter 870 %p/st31.12.2024 0.6688 ex87089510 ex87089599 20 30 Inflatable safety cushion of high strength polyamide fibre: sewn, folded, with three-dimensionally applied silicone bonding for air bag cavity forming and load-regulated air bag sealing, suitable for cool inflator technology 0 %p/st31.12.20250.6687 ex87089510 ex87089599 30 40 Inflatable sewn safety cushion of high strength polyamide fibre: folded into three-dimensional packing form, fixed by thermal forming, dedicated fixation seams, fabric cover or plastic staples, or flat safety cushion with or without thermal folding 0 %p/st31.12.20250.8292ex8708959950Airbag inflator containing both pyrotechnics and cold gas as propellant for safety airbags of vehicles, in each individual consignment of 1000 pieces or more0 %p/st31.12.20260.7444 ex87089910 ex87089997 25 45 Plastic air guide for directing air flow to the surface of intercooler for use in the production of motor vehicles0 %-31.12.20240.6583 ex87089910 ex87089997 60 50 Aluminium engine bracket, with dimensions of: height of more than 10 mm but not more than 200 mm, width of more than 10 mm but not more than 250 mm, length of more than 10 mm but not more than 200 mm, equipped with at least two fixing holes, made of aluminium alloys ENAC-46100 or ENAC-42100 (based on the norm EN:1706) with following characteristics: internal porosity not more than 1 mm, outer porosity not more than 2 mm, rockwell hardness HRB 10 or more, of a kind used in the production of suspensions systems for engines in motor vehicles 0 %p/st31.12.20240.7921ex8708999718 Hydrostatic speed changer: with a hydro pump and a differential with wheel axle, whether or not with a fan impeller and/or a pulley, for use in the manufacture of tractors of subheadings 87019190 and 87019290, whose main function is that of a lawn mower 0 %p/st31.12.2024 0.8127ex8708999728 A set of Type 4 H2 cylinders, in accordance with the EC 79 standard, consisting of two to eight cylinders on aluminum frames: cylinders made of high density polyethylene (HDPE) composite reinforced with a braid of glass and carbon fibers in epoxy resin, with an operating pressure of not less than 35 MPa, with a durability declared by the manufacturer of not less than 20 years, with a cylinder capacity of 180 liters or more but not more than 375 liters, equipped with a set of solenoid, manual and safety PRD valves,

with a total width of 1800 mm or more but not more than 2300 mm, with a total height of 400 mm or more but not more than 500 mm, with a total length of 1200 mm or more but not more than 3600 mm 0 %-31.12.20250.8128ex8708999738 A set of Compressed Natural Gas (CNG) cylinders type CNG-4, in accordance with the ECE R110 standard, consisting of four or five cylinders on aluminum frames: made of high density polyethylene (HDPE) composite reinforced with a braid of glass and carbon fibers in epoxy resin, with an operating pressure of not less than 20 MPa, with a shelf life declared by the manufacturer of not less than 20 years, with a cylinder capacity of 315 liters or more but not more than 375 liters, equipped with a set of solenoid, manual and safety PRD valves, with a total width of 2200 mm or more but not more than 2300 mm, with a total height of 450 mm or more but not more than 460 mm, with a total length of 3500 mm or more but not more than 3600 mm 0 %-31.12.2025 0.6686ex8714109010 Motorcycle fork rod inner tubes: of SAE1541 carbon steel, with a hard chromium layer of 20 µm (+ 15 µm/ – 5 µm), having a wall thickness of 1,3 mm or more, but not more than 1,6 mm, having an elongation at break of 15 %, perforated 0 %p/st31.12.20250.6848ex8714109070Motor bikes radiators in consignment of 100 pieces or more0 %p/st31.12.20270.6172 ex87149130 ex87149130 ex87149130 25 35 72 Front forks, except rigid (non-telescopic) front forks made entirely of steel, for use in the manufacture of bicycles (including electric bicycles)0 %-31.12.20240.6879ex8714961010Pedals, for use in the manufacture of bicycles (including electric bicycles)0 %-31.12.20250.7421 ex87149910 ex87149910 20 89 Bicycle handlebars: with or without an integrated stem, either made out of carbon fibres and synthetic resin or made of aluminium, for use in the manufacture of bicycles (including electric bicycles) 0 %-31.12.20270.7710 ex87149950 ex87149950 11 91 Derailleur gears, consisting of: rear derailleur and mounting articles, with or without front derailleur, for use in the manufacture of bicycles (including electric bicycles) 0 %p/st31.12.20240.6878ex8714999030Seat posts, for use in the manufacture of bicycles (including electric bicycles)0 %p/st31.12.20250.7708ex8714999040Stem for bicycle handlebars, for use in the manufacture of bicycles (including electric bicycles)0 %p/st31.12.20240.8507ex8714999050Rear air shock absorber in form of a pneumatic spring element with oil damper for use in the manufacture of bicycles, including electrical bicycles0 %-31.12.20270.3191ex9001109010Image reverser made up from an assembly of optical fibres0 %-31.12.2024 0.6402 ex90015041 ex90015049 40 40 Organic uncut corrective eyeglass lens, finished on both sides, to undergo a coating, colouring, edging, mounting or any other substantial process for use in the manufacture of corrective glasses0 %-31.12.20270.6401ex9001508030Round organic uncut, semi-finished eyeglass lens with corrective effect, finished on one side, of a kind used for the manufacture of finished eyeglass lenses0 %-31.12.20260.7590ex9002110018

Lens assembly consisting of a cylinder-shaped cover made of metal or plastic and optical elements with: a horizontal field of view range to a maximum of 120 deg, a diagonal field of view range to a maximum of 105 deg, a focal length to a maximum of 7,50 mm, a relative aperture of a maximum of F/2,90, a maximum diameter of 22 mm 0 %-31.12.20240.5692ex9002110020 Lenses: measuring not more than 95 mm × 55 mm × 50 mm, with a resolution of 160 lines/mm or better, and with a zoom ratio of 3 or more times 0 %-31.12.20270.7973ex9002110023 Lens with: motorized focus, zoom, aperture, electronically switchable infrared cut filter, an adjustable focal length not less than 2,7 mm and not more than 55mm, a weight of not more than 120 g, a length of less than 70 mm, a diameter of not more than 70 mm 0 %-31.12.20250.7103ex9002110045 Infrared optical unit with lenses of silicon, germanium or chalcogenide glass of a diameter not more than 62 mm (± 0,05 mm), whether or not mounted on a machined aluminium alloy support of a kind used for thermal cameras or IP network cameras 0 %-31.12.2026 0.3177ex9002110050 Lens unit: having a focal length of 25 mm or more but not more than 150 mm, consisting of glass or plastic lenses, with a diameter of 60 mm or more but not more than 190 mm 0 %-31.12.20240.6572ex9002110085 Lens assembly with: a horizontal field of view range of 20 deg or more, but not more than 200 deg, a focal length of 1,16 mm or more, but not more than 20 mm, a relative aperture of F/1,2 or more, but not more than F/4, and a diameter of 5 mm or more, but not more than 40 mm, for use in the manufacture of CMOS automotive cameras or in IP network cameras production 0 %-31.12.20240.5955ex9025804030 Electronic barometric semiconductor pressure sensor in a housing, mainly consisting of a combination of one or more monolithic application-specific integrated circuits (ASIC) and at least one or more microelectromechanical sensor elements (MEMS) manufactured with semiconductor technology, with mechanical components arranged in three-dimensional structures on the semiconductor material 0 %p/st31.12.20240.6288ex9025804050 Electronic semiconductor sensor for measuring at least two of the following quantities: Atmospheric pressure, temperature, (also for temperature compensation), humidity, or volatile organic compounds, in a housing suitable for the automatic printing of conductor boards or Bare Die technology, containing: one or more monolithic application-specific integrated circuits (ASIC), one or more microelectromechanical sensor elements (MEMS) manufactured with semiconductor technology, with mechanical components arranged in three-dimensional structures on the semiconductor material, of a kind used for incorporation into products of Chapters 84-90 and 95 0 %p/st31.12.2024 0.3292ex9032890030Electronic controller of electric power steering (EPS controller)0 %p/st31.12.20240.4253ex9032890040Digital valve controller for controlling liquids and gases0 %p/st31.12.20270.7004ex9032890050

Gas panel for regulating and controlling of the gas flow rate, working with plasma technology, comprising an electronic mass flow regulator, suitable for receiving and sending of analogue and digital signals four pressure transducers, two or more pressure valves, electric interfaces and several connectors for gas lines suitable for in-situ plasma bonding processes or for multi frequency bond activating processes 0 %-31.12.20260.5025ex9401992010Ratchet disk for use in the manufacture of reclining car seats0 %p/st31.12.20280.4846 ex95030075 ex95030095 10 10 Plastic cable car scale models, whether or not with a motor, for printing0 %p/st31.12.20250.6950ex9607201010Sliders, narrow tape with mounted zipper teeth, pin/boxes and other parts of slide fasteners, of base metal for use in the manufacture of zippers0 %-31.12.20240.6949ex9607209010Narrow strips mounted with plastic chain scoops for use in the manufacture of zippers0 %-31.12.20250.3286ex9608910010Non-fibrous plastic pen-tips with an internal canal0 %-31.12.20240.3289ex9608910020Felt tips and other porous-tips for markers, without internal canal0 %-31.12.20240.2737ex9612101010Ribbons of plastic with segments of different colours, providing the penetration of dyes by heat into a support (so called dye-sublimation)0 %-31.12.2024