Commission Implementing Regulation (EU) 2025/2620of 16 December 2025laying down rules for the application of Regulation (EU) 2023/956 of the European Parliament and of the Council as regards the calculation of the free allocation adjustment to the number of CBAM certificates to be surrendered(Text with EEA relevance)

Commission Implementing Regulation (EU) 2025/2620 of 16 December 2025 laying down rules for the application of Regulation (EU) 2023/956 of the European Parliament and of the Council as regards the calculation of the free allocation adjustment to the number of CBAM certificates to be surrendered (Text with EEA relevance) THE EUROPEAN COMMISSION, Having regard to the Treaty on the Functioning of the European Union, Having regard to Regulation (EU) 2023/956 of the European Parliament and of the Council of 10 May 2023 establishing a carbon border adjustment mechanism OJ L 130, 16.5.2023, p. 52, ELI: http://data.europa.eu/eli/reg/2023/956/oj. , and in particular Article 31(2) thereof, Whereas: (1) Regulation (EU) 2023/956 establishes the Carbon Border Adjustment Mechanism (CBAM) which seeks to replace the allocation of free allowances used to prevent the risk of carbon leakage under the system for greenhouse gas emission allowance trading within the Union established under Directive 2003/87/EC of the European Parliament and of the Council Directive 2003/87/EC of the European Parliament and of the Council of 13 October 2003 establishing a system for greenhouse gas emission allowance trading within the Union and amending Council Directive 96/61/EC (OJ L 275, 25.10.2003, p. 32, ELI: http://data.europa.eu/eli/dir/2003/87/oj). (the EU ETS). To ensure a gradual transition from the current system of free allowances in the EU ETS to the CBAM, the CBAM is to be progressively phased in, while free allowances in sectors covered by the CBAM are to be phased out. The combined and transitional application of EU ETS allowances allocated free of charge and of Regulation (EU) 2023/956 should in no case result in more favourable treatment for Union goods compared to goods imported into the customs territory of the Union. (2) Article 31(1) of Regulation (EU) 2023/956 therefore requires that the CBAM certificates to be surrendered are to be adjusted to reflect the extent to which EU ETS allowances are allocated free of charge. The Commission is to adopt implementing acts laying down detailed rules for the calculation of such adjustment (the free allocation adjustment). (3) The determination of the free allocation adjustment requires taking into account the quantity of imported goods, the cross-sectoral correction factor of the total amount of free allowances under the EU ETS, the relevant CBAM factor as established in Article 10a of Directive 2003/87/EC and a value combining the relevant EU ETS benchmarks for the goods concerned. By analogy with the EU ETS, that value should be called the CBAM benchmark. (4) The EU ETS benchmarks, used to determine the level of free allocation at the level of installations producing, within the Union, the goods listed in Annex I to Regulation (EU) 2023/956, apply to individual sub-installations, while the free allocation adjustment applies at the level of goods as listed in Annex I to Regulation (EU) 2023/956. Therefore, the CBAM benchmarks should be determined for each commodity code.

(5) Regulation (EU) 2023/956 allows authorised declarants to report the embedded emissions in imported CBAM goods based on either actual emissions or default values. The free allocation adjustment should reflect that principle. If actual emissions are declared, the free allocation adjustment should equally reflect the actual production process and the composition of goods (actual free allocation adjustment). If default values for emissions are declared, the adjustment should equally be based on default values for free allocation. (6) Under the EU ETS, free allocation is determined at installation level, using a limited number of product benchmarks. Where emissions and products cannot be assigned to product benchmarks, the heat and fuel benchmarks are used as fallback approaches. Where neither heat nor fuel fallback benchmarks can be assigned, relevant processes are allocated free allowances under a process emission sub-installation based on historical activity levels. For the purposes of the CBAM, those EU ETS benchmarks and fallback approaches should be combined to result in CBAM benchmarks that refer to specific goods. (7) The determination of the actual free allocation adjustment requires not only taking into account the processes at the installation where the goods are produced, but also the processes to produce input materials (precursors) used by the installation. Moreover, the CBAM requires more detailed information than the EU ETS, as the concept of dividing the installation into sub-installations according to the benchmarks would have to be applied at goods level. Finally, the actual free allocation adjustment of goods very much depends on the origin of the precursors and the composition of the goods. The determination of the actual free allocation should be as simple as possible while reflecting the actual conditions of the installation where the goods are produced, that is in terms of production route, the origin of precursors and the composition of goods. (8) The adjustment based on default values for free allocation should be determined based on default CBAM benchmarks. In order to ensure equivalence between embedded emissions and embedded free allocation, the default CBAM benchmarks should reflect the same conditions as those used for the determination of default values for emissions, that is, in terms of production route, the origin of precursors and the composition of goods. However, where this approach would lead to excessive complexity of the calculation rule, simplifying assumptions for the development of the CBAM benchmarks should be made. In particular, the CBAM benchmarks should be applicable independently of the country of origin of the imported good or precursor used. (9) EU ETS benchmarks are determined for the periods from 2021 to 2025 and from 2026 to 2030. In order to ensure equal treatment of imports, the CBAM benchmarks to be applied in the period from 2026 to 2030 should be based on the EU ETS benchmarks applicable during that period. Furthermore, the factor used for calculating the free allocation of process emissions sub-installations in the EU ETS from 1 January 2028 will be different from the value used until 2027. Therefore, CBAM benchmarks based on a process emissions fallback approach should take this change into account.

(10) EU ETS benchmarks for the period from 2026 to 2030 will only become available in early 2026. However, based on the already collected data, estimates with a high degree of certainty can already be made for the majority of the ETS benchmarks relevant for CBAM, while for the remaining ETS benchmarks estimates with a good degree of certainty can be made. In order to provide more certainty to importers of CBAM goods already at the beginning of 2026, the CBAM benchmarks in 2026 should be based on the estimated ETS benchmarks to be applied in the period from 2026 to 2030 and apply from 1 January 2026. These CBAM benchmarks should be reviewed at the latest one month after the final EU ETS benchmarks for the period from 2026 to 2030 are published. The updated CBAM benchmarks based on the final ETS benchmarks for the period 2026 to 2030 should apply to goods imported from 1 January 2027. Where the Commission receives evidence demonstrating that the CBAM benchmarks are too high or too low, it should revise the relevant CBAM benchmarks. (11) Article 10a(1), second subparagraph, of Directive 2003/87/EC provides that no free allocation is to be made in respect of any electricity production. Therefore, the free allocation adjustment for electrical energy (CN 2716 00 00) should be zero. (12) To simplify the identification of the reporting period for goods, with the exception of electricity imported into the customs territory of the Union, a presumption should be established that such goods were produced during the year of import. Authorised CBAM declarants should be given the possibility to rebut that presumption by providing evidence demonstrating the actual period during which the goods were produced. As the authorised CBAM declarants are to surrender the CBAM certificates that correspond to the declared embedded emissions for the first time in 2027 for the year 2026, the reporting period should not cover any period before 2026. (13) For precursors used in the production of a complex good, the operator of the complex good should, for the purpose of determining embedded free allocation based on actual emissions, identify the applicable reporting period during which the precursor was produced and use the corresponding verified actual values. To simplify the identification of the applicable reporting period, a presumption should be established that precursors used in the production of a complex good were produced during the reporting period during which that complex good was produced. Operators should be given the possibility to rebut that presumption by providing evidence to the verifier demonstrating the actual period during which the precursor was produced. As the authorised CBAM declarants are to surrender the CBAM certificates that correspond to the declared embedded emissions for the first time in 2027 for the year 2026, the reporting period should not cover any period before 2026. (14) To ensure consistency, the reporting period for the calculation of the free allocation adjustment should correspond to the reporting period used for the determination of embedded emissions based on actual values in accordance with Commission Implementing Regulation (EU) 2025/2547

Commission Implementing Regulation (EU) 2025/2547 of 10 December 2025 laying down rules for the application of Regulation (EU) 2023/956 of the European Parliament and the Council as regards the methods for the calculation of emissions embedded in goods (OJ L, 2025/2547, 22.12.2025, ELI: http://data.europa.eu/eli/reg_impl/2025/2547/oj). . (15) In order to reflect the EU ETS benchmarks, CBAM benchmarks for simple goods were calculated using the EU ETS product benchmarks of the same type of good. Where no product benchmark is defined, the average share of the heat versus the fuel benchmark for the period 2021-2025 in the EU ETS reported for relevant product groups in the relevant baseline data was used to determine their respective contribution to the CBAM benchmarks. As no data on energy consumption per tonne of good is available from EU ETS data, energy consumption levels to be applied to these fallback benchmarks as well as the level of process emissions, where relevant, were aligned with the data and assumptions used for the determination of default values for the embedded emissions. In order to further align the CBAM benchmarks for complex goods with the default values for embedded emissions, the quality and quantity of precursors implied in the calculation was aligned with the data used for the calculation of the default values embedded emissions. This includes the selection of reference levels of clinker contained in cement, formulation of mixed fertilisers, and alloy grades for steel. EU ETS benchmarks are not fully aligned with CN codes or the aggregated goods categories defined in Implementing Regulation (EU) 2025/2547. In particular, some EU ETS benchmarks depend on certain production routes. For ensuring that under the CBAM the respective goods are treated equally as under the EU ETS, production-route specific values were determined for primary and secondary aluminium as well as for crude steel based on blast furnace, direct reduced iron (DRI) and electric arc furnace (EAF) routes. (16) Union policy on the environment is to be based on the polluter pays principle, in accordance with Article 191(2) of the Treaty. This principle is also applied in the EU ETS for the free allocation of allowances, as set out in Commission Delegated Regulation (EU) 2019/331 Commission Delegated Regulation (EU) 2019/331 of 19 December 2018 determining transitional Union-wide rules for harmonised free allocation of emission allowances pursuant to Article 10a of Directive 2003/87/EC of the European Parliament and of the Council (OJ L 59, 27.2.2019, p. 8, ELI: http://data.europa.eu/eli/reg_del/2019/331/oj). . Currently, direct reduced iron (DRI) is covered by the hot metal benchmark of the EU ETS and, without further differentiation, imports of steel based on natural-gas DRI would receive a free allocation adjustment that exceeds their embedded emissions for the first years in which a CBAM obligation is due, which means that no CBAM certificates would be due for DRI-based goods. Compared to this, secondary steel imports would face a CBAM obligation, despite having lower actual embedded emissions than DRI. In addition, the potential free allocation adjustment stemming from the hot metal benchmark would create a situation in which more carbon-intensive natural gas based DRI imports would receive more free allocation adjustment than secondary steel producers, which receive comparably less free allocation based on the electric arc furnace (EAF) benchmarks, therefore increasing the carbon leakage risk for secondary steel producers in the Union. In line with the principles to be applied for the allocation of free allowances under the EU ETS, to ensure the environmental integrity of the CBAM and to address the potential risk of carbon leakage of the production of secondary steel in the Union, a dedicated CBAM benchmark for natural gas-based DRI should be created. Taking into account the relative level of embedded emissions, the level of the DRI benchmark should be chosen to ensure that the CBAM obligation for primary natural gas-based DRI imports is lower than for primary blast furnace steel, but higher than for secondary steel.

(17) The rules for the exchangeability of fuel and electricity have been removed for the determination of free allocation under the EU ETS starting in 2026. This means that free allocation granted under some ETS product benchmarks in the steel sector will cover indirect emissions to a certain extent. As the CBAM scope currently only covers direct emissions in the steel sector, only the direct emission share of the respective ETS benchmarks should be considered when determining the corresponding CBAM benchmarks. For these benchmarks, improvement rates in accordance with [points (c) and (d) of the third subparagraph of] Article 10a(2) of Directive 2003/87/EC do not appropriately reflect the direct emissions to be covered by the CBAM benchmarks. Therefore, the average direct emissions of the 10 % best installations under these ETS benchmarks in the new baseline years 2021 and 2022 should serve as proxy instead of the EU ETS benchmarks for the purpose of calculating the CBAM benchmarks. (18) In line with the European Commission’s Better Regulation guidelines, in parallel with technical consultations with the Member States, including at expert level, the European Commission carried out extensive consultations with relevant stakeholders, including industry representatives, to gather input in its preparatory work on the rules laid down in this Regulation. A call for evidence was organised between 28 August and 25 September 2025 to collect feedback on the main elements of this Regulation. (19) The provisions in this Regulation relate to the free allocation adjustment in respect of greenhouse gas emissions released from 1 January 2026. This Regulation should therefore apply from 1 January 2026. This Regulation should be revised in 2027. (20) The measures provided for in this Regulation are in accordance with the opinion of the CBAM Committee, HAS ADOPTED THIS REGULATION:

Article 1

Calculation of the adjustment to the number of CBAM certificates to be surrendered

1. The adjustment to the number of CBAM certificates, as referred to in Article 31 of Regulation (EU) 2023/956 (free allocation adjustment), shall be calculated in accordance with point 2 of the Annex to this Regulation.
2. The free allocation adjustment for electrical energy (CN code 2716 00 00) shall be zero.

Article 2

Use of actual values for the calculation of the free allocation The specific embedded free allocation of a good shall be calculated based on actual data in accordance with point 3 of the Annex.

Article 3

Use of default values for the calculation of the free allocation By way of derogation from Article 2, the free allocation adjustment shall be calculated based on default values in accordance with point 4 of the Annex, if default values for the specific embedded emissions are used in the CBAM declaration.

Article 4

Precursors produced in different installations Where an installation producing complex goods uses a type of precursor from multiple installations, the embedded free allocation of the complex goods shall by default be determined, for the part of the free allocation embedded in that precursor, as the weighted average of the free allocation embedded in the precursors of that type of precursor used from the different installations. However, if there is sufficient evidence demonstrating that the installation producing the complex goods used, for a given production process, only precursors from a single installation, or from a subset of installations, the embedded free allocation of precursors used in goods produced through that production process shall be determined, respectively, based on the embedded free allocation of precursors obtained from that single installation, or as the weighted average of free allocation embedded in the precursors used from the different installations part of the subset.

Article 5

Entry into force and application This Regulation shall enter into force on the third day following that of its publication in the Official Journal of the European Union. It shall apply from 1 January 2026. This Regulation shall be binding in its entirety and directly applicable in all Member States. Done at Brussels, 16 December 2025. For the Commission The President Ursula von der Leyen

Annex

ANNEX

1. DEFINITIONS For the purpose of this Annex, the following definitions shall apply: (1) aggregated goods categories’ means aggregated goods categories pursuant to Table 1 of point 2 of Annex I to Implementing Regulation (EU) 2025/2547; (2) reporting period means the period corresponding to the calendar year during which the good or, where applicable, the precursor was produced and to be used as reference for the determination of embedded emissions; (3) precursor means any input material into a production process included in the list of goods set out in Annex I to Regulation (EU) 2023/956; (4) production route means a specific technology used in a production process to produce goods.
2. CALCULATION OF THE FREE ALLOCATION ADJUSTMENT For each good g other than electricity listed in the CBAM declaration pursuant to Article 6 of Regulation (EU) 2023/956, the free allocation adjustment pursuant to Article 31 of that Regulation shall be calculated using the following equation: FAAgSEFAg,y × Mg(Equation 1) Where: FAAgis the free allocation adjustment of good g;SEFAg,yis the specific embedded free allocation of good g in year y expressed as t CO2e / tonne of good g;Mgis the mass of good g imported during the year to which the CBAM declaration applies;yis the reporting period identified in accordance with Article 7 of Implementing Regulation (EU) 2025/2547.
3. CALCULATION OF SPECIFIC EMBEDDED FREE ALLOCATION (SEFA) OF A GOOD USING ACTUAL DATA 3.1. Production process For a single production process, the process-level specific free allocation shall be calculated using the following equation: SFAProcg,yCBAMy × CSCFy × BMg(Equation 2) Where: SFAProcg,yis the process-level specific free allocation in year y calculated for the production process which yields good g, expressed as t CO2e / tonne of good g;yis the reporting period related to the production of good g;CBAMyis the CBAM factor referred to in Article 10a(1a) of Directive 2003/87/EC for the year y (dimensionless);CSCFyis the cross-sectoral correction factor for year y determined by the Commission pursuant to Article 14(6) of Delegated Regulation (EU) 2019/331 and published in accordance with Article 10a(5) of Directive 2003/87/EC (dimensionless);BMgis the process-related CBAM benchmark for the production process which yields good g, expressed as t CO2e / tonne of g produced, as set out in point 5, Column A, of this Annex. 3.2. SEFA of a simple good The SEFA of a simple good g shall be calculated using the following equation: SEFAg,ySFAProcg,y(Equation 3) Where: SFAProcg,yis the direct result of Equation 2.

3.3. SEFA of a complex good For a complex good, the calculation of the SEFA shall take into account the production process as well as the SEFA of each precursor and shall be calculated using the following equation: SEFAg,ySFAProcg,y +ni1mi,y × SEFAi,yi'(Equation 4) Where: SEFAg,yis the specific embedded free allocation for the complex good g in year y, expressed as t CO2e / tonne of good g;SFAProcg,yis the process-related specific free allocation in year y calculated for the production process which yields good g in accordance with Equation 2 expressed as t CO2e / tonne of good g;miis the specific mass of precursor i consumed for the production of one tonne of good g, as determined in accordance with the rules set out in Implementing Regulation (EU) 2025/2547, expressed as t/t;SEFAi,y’is the specific embedded free allocation of precursor i in year yi, expressed as t CO2e / tonne of precursor i;yis the reporting period identified in accordance with Article 7 of Implementing Regulation (EU) 2025/2547;yi’is the reporting period of precursor i used in the calculation of SEFAi as identified in accordance with Article 13 of Implementing Regulation (EU) 2025/2547. The specific mass mi,y of each precursor used shall be determined using the following equation: mi,yMi,yALi,y(Equation 5) Where: Mi,yis the total mass of the precursor i expressed in tonnes used during reporting period y for the production process related to the aggregated goods category to which good g belongs. Mi,y is determined in accordance with point E of Annex II to Implementing Regulation (EU) 2025/2547;ALi,yis the activity level, meaning the quantity of goods produced within the system boundaries of a production process, in year y of the production process related to the aggregated goods category to which good g belongs expressed in tonnes. ALi,y is determined in accordance with point F of Annex II to Implementing Regulation (EU) 2025/2547;yis the reporting period identified in accordance with Article 7 of Implementing Regulation (EU) 2025/2547. Where precursors are themselves complex goods, the calculation of SEFAi,y’ shall be repeated recursively using Equations 2, 3 and 4, as appropriate, until no more precursors are relevant. SEFAi,yi' for each precursor shall be determined using one of the following methods: (1) where the SEFAi,yi' value for the precursor i is provided by the producer and verified in accordance with Article 8 of Regulation (EU) 2023/956, the default reporting period of the precursor is used in accordance with Article 13 of Implementing Regulation (EU) 2025/2547 unless there is sufficient evidence to identify the actual year in accordance with Article 13 of Implementing Regulation (EU) 2025/2547. (2) where the SEFAi,yi' value for the precursor i is not provided by the producer, the default reporting period of the precursor is used in accordance with Article 13 of Implementing Regulation (EU) 2025/2547 and SEFAi,yi' is determined by selecting the appropriate BMg value from point 5, Column B, of this Annex, taking into account the following factors:

(a) the country of origin of precursor i; (b) the CN code for precursor i; (c) if applicable, further parameters defining the precursor i, as specified in Annex to Implementing Regulation (EU) 2025/2547; (d) if applicable, the [default] production route specified for the country of origin of precursor i as specified in Annex to Implementing Regulation (EU) 2025/2547. 4. CALCULATION OF SPECIFIC EMBEDDED FREE ALLOCATION (SEFA) OF A GOOD USING DEFAULT VALUES Where default values are used, the SEFA is calculated using the following equation: SEFAg,yCBAMy × CSCFy × BMg(Equation 6) Where: CBAMyis the CBAM factor referred to in Article 10a(1a) of Directive 2003/87/EC for the year y (dimensionless);CSCFyis the cross-sectoral correction factor for the reporting period y determined by the Commission pursuant to Article 14(6) of Delegated Regulation (EU) 2019/331 and published in accordance with Article 10a(5) of Directive 2003/87/EC (dimensionless);BMgis the default CBAM benchmark set out in point 5, Column B, of this Annex;yis the reporting period as identified in accordance with Article 7 of Implementing Regulation (EU) 2025/2547. For the purpose of selecting the appropriate value for BMg the following parameters shall be taken into account: (a) the country of origin of good g; (b) the CN code for good g; (c) if applicable, further parameters defining the good g, as specified in Annex to Implementing Regulation (EU) 2025/2547; (d) if applicable, the [default] production route specified for the country of origin as specified in Annex I to Implementing Regulation (EU) 2025/2547. 5. CBAM BENCHMARKS 5.1. Rules for selecting the appropriate CBAM benchmark value when using default values Where default values are used to determine SEFA of a final good or of a precursor, the same production route shall be used as indicated in Annex I to Commission Implementing Regulation (EU) 2025/2621 Commission Implementing Regulation (EU) 2025/2621 of 16 December 2025 laying down rules for the application of Regulation (EU) 2023/956 of the European Parliament and the Council as regards the establishment of default values (not yet published in the Official Journal). for the country of origin of that good or precursor. Where different alloy grades for steel are given in the table for the same CN code, the highest benchmark value given for the relevant production year is used. 5.2. Rules for selecting the appropriate CBAM benchmark value when using actual data 5.2.1. Cement White cement clinker means cement clinker for use as main binding component in the formulation of materials such as joint filers, ceramic tile adhesives, insulation, and anchorage mortars, industrial floor mortars, ready mixed plaster, repair mortars, and water- tight coatings with maximum average contents of 0,4 mass-% Fe2O3, 0,003 mass-% Cr2O3 and 0,03 mass-% Mn2O3. Grey cement clinker means other cement clinker than white cement clinker. In the case of other hydraulic cements (CN 25239000) containing a mixture of white clinker and of grey clinker and/or calcined clay, the CBAM benchmark shall be calculated as a weighted average that reflects the composition.

5.2.2. Fertilisers No specific rules apply. 5.2.3. Iron and steel Carbon steel means steel other than stainless steel, high alloy or low alloy steel. Stainless steel means alloy steels containing, by weight, 1,2 % or less of carbon and 10,5 % or more of chromium, with or without other elements. High alloy steel means steel containing 8 % [or more metallic alloying elements or where high surface quality and processability is required]. Low alloy steel means alloy steel other than high-alloy steel. 5.2.4. Aluminium No specific rules apply. 5.3. CBAM benchmark values Where more than one benchmark value is given for a specific CN code, the meaning of the indicators is as follows: (1) Value is to be used for production years 2026-27 (2) Value is to be used for production years 2028-30 (A) grey clinker / cement (B) white clinker / cement (C) Carbon Steel based on BF/BOF (D) Carbon Steel based on DRI/EAF (E) Carbon Steel based on Scrap/EAF (F) Low alloy Steel based on BF/BOF (G) Low alloy Steel based on DRI/EAF (H) Low alloy Steel based on scrap/EAF (J) High alloy Steel (based on EAF) (K) primary Aluminium (L) secondary Aluminium CN codeCN Description Column A BMg [tCO2e/t] Column B BMg [tCO2e/t] Cement25070080Kaolinic clays (other than kaolin)0,6660,66625231000Cement clinkers 0,666 (A) 0,859 (B) 0,666 (A) 0,859 (B) 25232100White portland cement, whether or not artificially coloured0,0000,85925232900Portland cement (excl. white, whether or not artificially coloured)0,0000,66625233000Aluminous cement 0,717 (1) 0,686 (2) 0,717 (1) 0,686 (2) 25239000Cement, whether or not coloured (excl. portland cement and aluminous cement) 0,000 (A) 0,000 (B) 0,666 (A) 0,847 (B) Hydrogen28041000Hydrogen5,0895,089Fertilisers28080000Nitric acid; sulphonitric acids0,1510,58228141000Anhydrous ammonia1,5221,52228142000Ammonia in aqueous solution0,4570,45728342100Nitrate of potassium0,0190,62631021012Urea in aqueous solution, containing > 45 % nitrogen in relation to the weight of the dry product and containing ≥ 31,8 % but ≤ 33,2 % by weight of urea (excl. that in packages with a gross weight of ≤ 10 kg)0,0180,30431021015Urea in aqueous solution, containing > 45 % nitrogen in relation to the weight of the dry product and containing > 33,2 % but ≤ 55 % by weight of urea (excl. that in packages with a gross weight of ≤ 10 kg)0,0290,50331021019Urea, whether or not in aqueous solution, containing > 45 % nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of ≤ 10 kg, or in aqueous solution containing ≥ 31,8 % but ≤ 55 % by weight of urea)0,0530,90231021090Urea, whether or not in aqueous solution, containing ≤ 45 % by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of ≤ 10 kg)0,0510,882 31022100Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of ≤ 10 kg)0,0220,41431022900Double salts and mixtures of ammonium sulphate and ammonium nitrate (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of ≤ 10 kg)0,0190,56631023010Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of ≤ 10 kg)0,0000,50831023090Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of ≤ 10 kg)0,0190,76731024010Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing ≤ 28 % nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of ≤ 10 kg)0,0190,68831024090Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28 % nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of ≤ 10 kg)0,0190,68831025000Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of ≤ 10 kg)

0,270 (1) 0,254 (2) 0,701 (1) 0,685 (2) 31026000Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of ≤ 10 kg)0,0420,63331028000Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of ≤ 10 kg)0,0000,62531029000Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages ≤ 10 kg)0,0530,84731051000Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of ≤ 10 kg0,0190,376 31052010Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of ≤ 10 kg)0,0900,43431052090Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content ≤ 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of ≤ 10 kg)0,0900,31931053000Diammonium hydrogenorthophosphate diammonium phosphate (excl. that in tablets or similar forms, or in packages with a gross weight of ≤ 10 kg)0,0060,33931054000Ammonium dihydrogenorthophosphate monoammonium phosphate, whether or not mixed with diammonium hydrogenorthophosphate diammonium phosphate (excl. that in tablets or similar forms, or in packages with a gross weight of ≤ 10 kg)0,0060,17331055100Mineral or chemical fertilisers containing nitrates and phosphates (excl. ammonium dihydrogenorthophosphate Monoammonium phosphate, diammonium hydrogenorthophosphate Diammonium phosphate, and those in tablets or similar forms, or in packages with a gross weight of ≤ 10 kg)0,0900,54831055900Mineral or chemical fertilisers containing the two fertilising elements nitrogen (excl. nitrate) and phosphorus but not nitrates (excl. ammonium dihydrogenorthophosphate monoammonium phosphate, diammonium hydrogenorthophosphate diammonium phosphate in tablets or similar forms, or in packages with a gross weight of ≤ 10 kg)0,0060,39131059020Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10 % nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of ≤ 10 kg)0,0190,47631059080Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of ≤ 10 % (excl. in tablets or similar forms or in packages of a gross weight of ≤ 10 kg)0,0190,248

Iron & Steel26011200Agglomerated iron ores and concentrates (excl. roasted iron pyrites)0,0860,08672011011Non-alloy pig iron in pigs, blocks or other primary forms, containing by weight ≤ 0,5 % phosphorus, ≥ 0,4 % manganese and ≤ 1 % silicon1,0891,21072011019Non-alloy pig iron in pigs, blocks or other primary forms, containing by weight ≤ 0,5 % phosphorus, ≥ 0,4 % manganese and > 1 % silicon1,0891,21072011030Non-alloy pig iron in pigs, blocks or other primary forms, containing by weight ≤ 0,5 % phosphorus, and ≥ 0,1 % but < 0,4 % manganese1,0891,21072011090Non-alloy pig iron in pigs, blocks or other primary forms, containing by weight ≤ 0,5 % phosphorus, and ≤ 0,1 % manganese1,0891,21072012000Non-alloy pig iron in pigs, blocks or other primary forms, containing by weight ≥ 0,5 % phosphorus1,0891,21072015010Alloy pig iron in pigs, blocks or other primary forms, containing by weight ≥ 0,3 % but ≤ 1 % titanium and ≥ 0,5 % but ≤ 1 % vanadium1,0891,21072015090Alloy pig iron and spiegeleisen, in pigs, blocks or other primary forms (excl. alloy iron containing, by weight, ≥ 0,3 % but ≤ 1 % titanium and ≥ 0,5 % but ≤ 1 % vanadium)1,0891,21072021120Ferro-manganese, containing by weight > 2 % carbon, with a granulometry ≤ 5 mm and a manganese content by weight > 65 % 1,361 (1) 1,277 (2) 1,361 (1) 1,277 (2) 72021180Ferro-manganese, containing by weight > 2 % carbon (excl. ferro-manganese with a granulometry of ≤ 5 mm and containing by weight > 65 % manganese) 1,361 (1) 1,277 (2) 1,361 (1) 1,277 (2) 72021900Ferro-manganese, containing by weight ≤ 2 % carbon 1,361 (1) 1,277 (2) 1,361 (1) 1,277 (2) 72024110Ferro-chromium, containing by weight > 4 % but ≤ 6 % carbon 1,142 (1) 1,106 (2) 1,142 (1) 1,106 (2) 72024190Ferro-chromium, containing by weight > 6 % carbon 1,142 (1) 1,106 (2) 1,142 (1) 1,106 (2) 72024910Ferro-chromium, containing by weight ≤ 0,05 % carbon 1,142 (1) 1,106 (2) 1,142 (1) 1,106 (2) 72024950Ferro-chromium, containing by weight > 0,05 % but ≤ 0,5 % carbon 1,142 (1) 1,106 (2) 1,142 (1) 1,106 (2) 72024990Ferro-chromium, containing by weight > 0,5 % but ≤ 4 % carbon 1,142 (1) 1,106 (2) 1,142 (1) 1,106 (2) 72026000Ferro-nickel 2,390 (1) 2,295 (2) 2,390 (1) 2,295 (2) 72031000Ferrous products obtained by direct reduction of iron ore, in lumps, pellets or similar forms0,2950,39772039000Spongy ferrous products, obtained from molten pig iron by atomisation, iron of a purity of ≥ 99,94 %, in lumps, pellets or similar forms0,2950,39772051000Granules, of pig iron, spiegeleisen, iron or steel (excl. granules of ferro-alloys, turnings and filings of iron or steel, certain small calibre items, defective balls for ball-bearings)0,000 1,288 (C) 0,424 (D) 0,027 (E) 72052100Powders, of alloy steel (excl. powders of ferro-alloys and radioactive iron powders isotopes)0,000 1,460 (F)(1) 0,659 (G)(1) 0,328 (H)(1) 0,852 (J)(1) 1,298 (F)(2) 0,647 (G)(2) 0,315 (H)(2) 0,820 (J)(2) 72052900Powders, of pig iron, spiegeleisen, iron or non-alloy steel (excl. powders of ferro-alloys and radioactive iron powders isotopes)0,000

1,288 (C) 0,424 (D) 0,027 (E) 72061000Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 0,150 (C) 0,027 (D) 0,027 (E) 1,288 (C) 0,424 (D) 0,027 (E) 72069000Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 0,150 (C) 0,027 (D) 0,027 (E) 1,288 (C) 0,424 (D) 0,027 (E) 72071111Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25 % carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 0,188 (C) 0,065 (D) 0,065 (E) 1,364 (C) 0,475 (D) 0,066 (E) 72071114Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25 % carbon, of square or rectangular cross-section, the width < twice the thickness of ≤ 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 0,188 (C) 0,065 (D) 0,065 (E) 1,364 (C) 0,475 (D) 0,066 (E) 72071116Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25 % carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 0,188 (C) 0,065 (D) 0,065 (E) 1,364 (C) 0,475 (D) 0,066 (E) 72071190Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 % carbon, of rectangular cross-section, the width < twice the thickness, forged 0,453 (C) 0,330 (D) 0,330 (E) 1,629 (C) 0,740 (D) 0,331 (E) 72071210Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular other than square cross-section, the width measuring ≥ twice the thickness, rolled or obtained by continuous casting 0,188 (C) 0,065 (D) 0,065 (E) 1,364 (C) 0,475 (D) 0,066 (E) 72071290Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 % carbon, of rectangular other than square cross-section, the width ≥ twice the thickness, forged 0,453 (C) 0,330 (D) 0,330 (E) 1,629 (C) 0,740 (D) 0,331 (E) 72071912Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25 % carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 0,188 (C) 0,065 (D) 0,065 (E) 1,364 (C) 0,475 (D) 0,066 (E) 72071919Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 % carbon, of circular or polygonal cross-section, forged 0,453 (C) 0,330 (D) 0,330 (E) 1,629 (C) 0,740 (D) 0,331 (E) 72071980Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 % carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 0,188 (C) 0,065 (D) 0,065 (E) 1,364 (C) 0,475 (D) 0,066 (E) 72072011Semi-finished products, of non-alloy free-cutting steel, containing by weight ≥ 0,25 % carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 0,188 (C) 0,065 (D)

0,065 (E) 1,364 (C) 0,475 (D) 0,066 (E) 72072015Semi-finished products of iron or non-alloy steel, containing by weight ≥ 0,25 % but < 0,6 % carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 0,188 (C) 0,065 (D) 0,065 (E) 1,364 (C) 0,475 (D) 0,066 (E) 72072017Semi-finished products of iron or non-alloy steel, containing by weight ≥ 0,6 % carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 0,188 (C) 0,065 (D) 0,065 (E) 1,364 (C) 0,475 (D) 0,066 (E) 72072019Semi-finished products of iron or non-alloy steel, containing by weight ≥ 0,25 % carbon, of square or rectangular cross-section, the width < twice the thickness, forged 0,453 (C) 0,330 (D) 0,330 (E) 1,629 (C) 0,740 (D) 0,331 (E) 72072032Semi-finished products of iron or non-alloy steel, containing by weight ≥ 0,25 of carbon, of rectangular other than square cross-section, the width measuring ≥ twice the thickness, rolled or obtained by continuous casting 0,188 (C) 0,065 (D) 0,065 (E) 1,364 (C) 0,475 (D) 0,066 (E) 72072039Semi-finished products of iron or non-alloy steel, containing by weight ≥ 0,25 % carbon, of rectangular other than square cross-section and the width ≥ twice the thickness, forged 0,453 (C) 0,330 (D) 0,330 (E) 1,629 (C) 0,740 (D) 0,331 (E) 72072052Semi-finished products of iron or non-alloy steel, containing by weight ≥ 0,25 % carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 0,188 (C) 0,065 (D) 0,065 (E) 1,364 (C) 0,475 (D) 0,066 (E) 72072059Semi-finished products of iron or non-alloy steel, containing by weight ≥ 0,6 % carbon, of circular or polygonal cross-section, forged 0,453 (C) 0,330 (D) 0,330 (E) 1,629 (C) 0,740 (D) 0,331 (E) 72072080Semi-finished products of iron or non-alloy steel, containing by weight ≥ 0,25 % carbon (excl. those of square, rectangular, circular or polygonal cross-section) 0,188 (C) 0,065 (D) 0,065 (E) 1,364 (C) 0,475 (D) 0,066 (E) 72081000Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, in coils, simply hot-rolled, not clad, plated or coated, with patterns in relief directly due to the rolling process0,044 1,370 (C) 0,481 (D) 0,072 (E) 72082500Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, in coils, simply hot-rolled, not clad, plated or coated, of a thickness of ≥ 4,75 mm, pickled, without patterns in relief0,044 1,370 (C) 0,481 (D) 0,072 (E) 72082600Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, in coils, simply hot-rolled, not clad, plated or coated, of a thickness of ≥ 3 mm but < 4,75 mm, pickled, without patterns in relief0,044 1,370 (C) 0,481 (D) 0,072 (E) 72082700Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, in coils, simply hot-rolled, not clad, plated or coated, of a thickness of < 3 mm, pickled, without patterns in relief0,044

1,370 (C) 0,481 (D) 0,072 (E) 72083600Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, in coils, simply hot-rolled, not clad, plated or coated, of a thickness of ≥ 10 mm, not pickled, without patterns in relief0,044 1,370 (C) 0,481 (D) 0,072 (E) 72083700Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, in coils, simply hot-rolled, not clad, plated or coated, of a thickness of ≥ 4,75 mm but < 10 mm, not pickled, without patterns in relief0,044 1,370 (C) 0,481 (D) 0,072 (E) 72083800Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, in coils, simply hot-rolled, not clad, plated or coated, of a thickness of ≥ 3 mm but < 4,75 mm, not pickled, without patterns in relief0,044 1,370 (C) 0,481 (D) 0,072 (E) 72083900Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, in coils, simply hot-rolled, not clad, plated or coated, of a thickness of < 3 mm, not pickled, without patterns in relief0,044 1,370 (C) 0,481 (D) 0,072 (E) 72084000Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, not in coils, simply hot-rolled, not clad, plated or coated, with patterns in relief directly due to the rolling process0,044 1,370 (C) 0,481 (D) 0,072 (E) 72085120Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, not in coils, simply hot-rolled, not clad, plated or coated, of a thickness of > 15 mm, without patterns in relief0,044 1,370 (C) 0,481 (D) 0,072 (E) 72085191Flat-rolled products of iron or non-alloy steel, of a width of ≥ 2.050 mm, not in coils, simply hot-rolled, not clad, plated or coated, of a thickness of > 10 mm but ≤ 15 mm, without patterns in relief (excl. wide flats)0,044 1,370 (C) 0,481 (D) 0,072 (E) 72085198Flat-rolled products of iron or non-alloy steel, of a width of < 2.050 mm but ≥ 600 mm, not in coils, simply hot-rolled, not clad, plated or coated, of a thickness of > 10 mm but ≤ 15 mm, without patterns in relief0,044 1,370 (C) 0,481 (D) 0,072 (E) 72085210Flat-rolled products of iron or non-alloy steel, of a width of ≤ 1.250 mm, not in coils, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a thickness of ≥ 4,75 mm but ≤ 10 mm, without patterns in relief0,044 1,370 (C) 0,481 (D) 0,072 (E) 72085291Flat-rolled products of iron or non-alloy steel, of a width of ≥ 2.050 mm, not in coils, simply hot-rolled, not clad, plated or coated, of a thickness of ≥ 4,75 mm but ≤ 10 mm, without patterns in relief0,044 1,370 (C) 0,481 (D) 0,072 (E) 72085299Flat-rolled products of iron or non-alloy steel, of a width of < 2.050 mm but ≥ 600 mm, not in coils, simply hot-rolled, not clad, plated or coated, of a thickness of ≥ 4,75 mm but ≤ 10 mm, without patterns in relief (excl. rolled on four faces or in a closed bow pass of a width ≤ 1.250 mm)0,044 1,370 (C) 0,481 (D) 0,072 (E) 72085310Flat-rolled products of iron or non-alloy steel, of a width of ≤ 1.250 mm, not in coils, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a thickness of ≥ 4 mm but < 4,75 mm, without patterns in relief0,044

1,370 (C) 0,481 (D) 0,072 (E) 72085390Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, not in coils, simply hot-rolled, not clad, plated or coated, of a thickness of ≥ 3 mm but < 4,75 mm, without patterns in relief (excl. rolled on four faces or in a closed bow pass of a width ≤ 1.250 mm and of a thickness of ≥ 4 mm)0,044 1,370 (C) 0,481 (D) 0,072 (E) 72085400Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, not in coils, simply hot-rolled, not clad, plated or coated, of a thickness of < 3 mm, without patterns in relief0,044 1,370 (C) 0,481 (D) 0,072 (E) 72089020Flat-rolled products of iron or steel, of a width ≥ 600 mm, hot-rolled and further worked, but not clad, plated or coated, perforated0,044 1,370 (C) 0,481 (D) 0,072 (E) 72089080Flat-rolled products of iron or steel, of a width ≥ 600 mm, hot-rolled and further worked, but not clad, plated or coated, non-perforated0,044 1,370 (C) 0,481 (D) 0,072 (E) 72091500Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, in coils, simply cold-rolled cold-reduced, not clad, plated or coated, of a thickness of ≥ 3 mm0,079 1,458 (C) 0,533 (D) 0,108 (E) 72091610Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, in coils, simply cold-rolled cold-reduced, of a thickness of > 1 mm but < 3 mm electrical0,079 1,458 (C) 0,533 (D) 0,108 (E) 72091690Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, in coils, simply cold-rolled cold-reduced, of a thickness of > 1 mm but < 3 mm electrical0,079 1,458 (C) 0,533 (D) 0,108 (E) 72091710Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, in coils, simply cold-rolled cold-reduced, of a thickness of ≥ 0,5 mm but ≤ 1 mm electrical0,079 1,458 (C) 0,533 (D) 0,108 (E) 72091790Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, in coils, simply cold-rolled cold-reduced, not clad, plated or coated, of a thickness of ≥ 0,5 mm but ≤ 1 mm (excl. electrical)0,079 1,458 (C) 0,533 (D) 0,108 (E) 72091810Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, in coils, simply cold-rolled cold-reduced, of a thickness of < 0,5 mm electrical0,079 1,458 (C) 0,533 (D) 0,108 (E) 72091891Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, in coils, simply cold-rolled cold-reduced, not clad, plated or coated, of a thickness of ≥ 0,35 mm but < 0,5 mm (excl. electrical)0,079 1,458 (C) 0,533 (D) 0,108 (E) 72091899Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, in coils, simply cold-rolled cold-reduced, not clad, plated or coated, of a thickness of < 0,35 mm (excl. electrical)0,079 1,458 (C) 0,533 (D) 0,108 (E) 72092500Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, not in coils, simply cold-rolled cold-reduced, not clad, plated or coated, of a thickness of ≥ 3 mm0,079 1,458 (C) 0,533 (D) 0,108 (E) 72092610Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, not in coils, simply cold-rolled cold-reduced, of a thickness of > 1 mm but < 3 mm electrical0,079

1,458 (C) 0,533 (D) 0,108 (E) 72092690Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, not in coils, simply cold-rolled cold-reduced, not clad, plated or coated, of a thickness of > 1 mm but < 3 mm (excl. electrical)0,079 1,458 (C) 0,533 (D) 0,108 (E) 72092710Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, not in coils, simply cold-rolled cold-reduced, of a thickness of ≥ 0,5 mm but ≤ 1 mm electrical0,079 1,458 (C) 0,533 (D) 0,108 (E) 72092790Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, not in coils, simply cold-rolled cold-reduced, not clad, plated or coated, of a thickness of ≥ 0,5 mm but ≤ 1 mm (excl. electrical)0,079 1,458 (C) 0,533 (D) 0,108 (E) 72092810Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, not in coils, simply cold-rolled cold-reduced, of a thickness of < 0,5 mm electrical0,079 1,458 (C) 0,533 (D) 0,108 (E) 72092890Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, not in coils, simply cold-rolled cold-reduced, not clad, plated or coated, of a thickness of < 0,5 mm (excl. electrical)0,079 1,458 (C) 0,533 (D) 0,108 (E) 72099020Flat-rolled products of iron or steel, of a width of ≥ 600 mm, cold-rolled cold-reduced and further worked, but not clad, plated or coated, perforated0,079 1,458 (C) 0,533 (D) 0,108 (E) 72099080Flat-rolled products of iron or steel, of a width of ≥ 600 mm, cold-rolled cold-reduced and further worked, but not clad, plated or coated, non-perforated0,079 1,458 (C) 0,533 (D) 0,108 (E) 72101100Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, hot-rolled or cold-rolled cold-reduced, tinned, of a thickness of ≥ 0,5 mm0,112 1,491 (C) 0,567 (D) 0,141 (E) 72101220Tinplate of iron or non-alloy steel, of a width of ≥ 600 mm and of a thickness of < 0,5 mm, tinned [coated with a layer of metal containing, by weight, ≥ 97 % of tin], not further worked than surface-treated0,112 1,491 (C) 0,567 (D) 0,141 (E) 72101280Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, hot-rolled or cold-rolled cold-reduced, plated or coated with tin, of a thickness of < 0,5 mm (excl. tinplate)0,112 1,491 (C) 0,567 (D) 0,141 (E) 72102000Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, hot-rolled or cold-rolled cold-reduced, plated or coated with lead, incl. terne-plate0,112 1,491 (C) 0,567 (D) 0,141 (E) 72103000Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, hot-rolled or cold-rolled cold-reduced, electrolytically plated or coated with zinc0,112 1,491 (C) 0,567 (D) 0,141 (E) 72104100Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, hot-rolled or cold-rolled cold-reduced, corrugated, plated or coated with zinc (excl. electrolytically plated or coated with zinc)0,112 1,491 (C) 0,567 (D) 0,141 (E) 72104900Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, hot-rolled or cold-rolled cold-reduced, not corrugated, plated or coated with zinc (excl. electrolytically plated or coated with zinc)0,112

1,491 (C) 0,567 (D) 0,141 (E) 72105000Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, hot-rolled or cold-rolled cold-reduced, plated or coated with chromium oxides or with chromium and chromium oxides0,112 1,491 (C) 0,567 (D) 0,141 (E) 72106100Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, hot-rolled or cold-rolled cold-reduced, plated or coated with aluminium-zinc alloys0,112 1,491 (C) 0,567 (D) 0,141 (E) 72106900Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, hot-rolled or cold-rolled cold-reduced, plated or coated with aluminium (excl. products plated or coated with aluminium-zinc alloys)0,112 1,491 (C) 0,567 (D) 0,141 (E) 72107010Tinplate of a width of ≥ 600 mm and of a thickness of < 0,5 mm, tinned [coated with a layer of metal containing, by weight, ≥ 97 % of tin], not further worked than varnished, and flat products plated or coated with chromium oxides or with chromium and chromium oxides, of iron or non-alloy steel, of a width of ≥ 600 mm, hot-rolled or cold-rolled cold-reduced, varnished0,112 1,491 (C) 0,567 (D) 0,141 (E) 72107080Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, hot-rolled or cold-rolled cold-reduced, painted, varnished or plastic coated (excl. tinplate and products electrolytically plated or coated with chrome, varnished)0,112 1,491 (C) 0,567 (D) 0,141 (E) 72109030Flat-rolled products of iron or non-alloy steel, of a width of ≥ 600 mm, hot-rolled or cold-rolled cold-reduced, clad0,112 1,491 (C) 0,567 (D) 0,141 (E) 72109040Flat-rolled products of iron or non-alloy steel, tinned and printed, of a width of ≥ 600 mm, hot-rolled or cold-rolled cold-reduced0,112 1,491 (C) 0,567 (D) 0,141 (E) 72109080Flat-rolled products of iron or non-alloy steel, hot-rolled or cold-rolled cold-reduced, of a width of ≥ 600 mm, plated or coated (excl. plated or coated with thin, lead incl. terne-plate, zinc, aluminium, chromium, chromium oxides, plastics, platinum, painted or varnished, clad and tinned and printed)0,112 1,491 (C) 0,567 (D) 0,141 (E) 72111300Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of ≥ 4 mm, not in coils, without patterns in relief, commonly known as wide flats0,044 1,370 (C) 0,481 (D) 0,072 (E) 72111400Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of ≥ 4,75 mm (excl. wide flats)0,044 1,370 (C) 0,481 (D) 0,072 (E) 72111900Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. wide flats)0,044 1,370 (C) 0,481 (D) 0,072 (E) 72112320Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled cold-reduced, not clad, plated or coated, containing by weight < 0,25 % of carbon electrical0,079

1,458 (C) 0,533 (D) 0,108 (E) 72112330Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm and of a thickness of ≥ 0,35 mm, simply cold-rolled cold-reduced, not clad, plated or coated, containing by weight < 0,25 % of carbon (excl. electrical plate)0,079 1,458 (C) 0,533 (D) 0,108 (E) 72112380Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm and of a thickness of < 0,35 mm, simply cold-rolled cold-reduced, not clad, plated or coated, containing by weight < 0,25 % of carbon (excl. electrical plate)0,079 1,458 (C) 0,533 (D) 0,108 (E) 72112900Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled cold-reduced, not clad, plated or coated, containing by weight ≥ 0,25 % of carbon0,079 1,458 (C) 0,533 (D) 0,108 (E) 72119020Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled cold-reduced and further worked, but not clad, plated or coated, perforated0,079 1,458 (C) 0,533 (D) 0,108 (E) 72119080Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled cold-reduced and further worked, but not clad, plated or coated non-perforated0,079 1,458 (C) 0,533 (D) 0,108 (E) 72121010Tinplate of iron or non-alloy steel, of a width of < 600 mm and of a thickness of < 0,5 mm, tinned [coated with a layer of metal containing, by weight, ≥ 97 % of tin], not further worked than surface-treated0,112 1,491 (C) 0,567 (D) 0,141 (E) 72121090Flat-rolled products of iron or non-alloy steel, hot-rolled or cold-rolled cold-reduced, of a width of < 600 mm, tinned (excl. tinplate, not further worked than surface-treated)0,112 1,491 (C) 0,567 (D) 0,141 (E) 72122000Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled cold-reduced, electrolytically plated or coated with zinc0,112 1,491 (C) 0,567 (D) 0,141 (E) 72123000Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled cold-reduced, tinned (excl. electrolytically plated or coated with zinc)0,112 1,491 (C) 0,567 (D) 0,141 (E) 72124020Tinplate of a width of < 600 mm and of a thickness of < 0,5 mm, tinned [coated with a layer of metal containing, by weight, ≥ 97 % of tin], not further worked than varnished, and flat products plated or coated with chromium oxides or with chromium and chromium oxides, of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled cold-reduced, varnished0,112 1,491 (C) 0,567 (D) 0,141 (E) 72124080Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled cold-reduced, painted, varnished or plastic coated (excl. tinplate, not further worked than varnished, and products plated or coated with chromium oxides or with chromium and chromium oxides, varnished)0,112 1,491 (C) 0,567 (D) 0,141 (E) 72125020Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled cold-reduced, plated or coated with chromium oxides or with chromium and chromium oxides (excl. varnished)0,112

1,491 (C) 0,567 (D) 0,141 (E) 72125030Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled cold-reduced, plated or coated with chromium or nickel0,112 1,491 (C) 0,567 (D) 0,141 (E) 72125040Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled cold-reduced, plated or coated with copper0,112 1,491 (C) 0,567 (D) 0,141 (E) 72125061Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled cold-reduced, plated or coated with aluminium-zinc alloys0,112 1,491 (C) 0,567 (D) 0,141 (E) 72125069Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled cold-reduced, plated or coated with aluminium (excl. products plated or coated with aluminium-zinc alloys)0,112 1,491 (C) 0,567 (D) 0,141 (E) 72125090Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled cold-reduced, clad (excl. products plated or coated with tin or zinc, copper, with chromium oxides or with chromium and chromium oxides, chromium, nickel or aluminium, painted or varnished, and plastic-coated)0,112 1,491 (C) 0,567 (D) 0,141 (E) 72126000Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled cold-reduced, clad0,112 1,491 (C) 0,567 (D) 0,141 (E) 72131000Bars and rods, hot-rolled, in irregularly wound coils of iron or non-alloy steel, with indentations, ribs, grooves or other deformations produced during the rolling process0,038 1,364 (C) 0,475 (D) 0,066 (E) 72132000Bars and rods, hot-rolled, in irregularly wound coils, of non-alloy free-cutting steel (excl. bars and rods containing indentations, ribs, grooves or other deformations produced during the rolling process)0,038 1,364 (C) 0,475 (D) 0,066 (E) 72139110Bars and rods, hot-rolled, of the type used for concrete reinforcement, smooth, of iron or non-alloy steel, in irregularly wound coils, of circular cross-section measuring < 14 mm in diameter0,038 1,364 (C) 0,475 (D) 0,066 (E) 72139120Bars and rods, hot-rolled, of the type used for tyre cord, smooth, of iron or non-alloy steel, in irregularly wound coils0,038 1,364 (C) 0,475 (D) 0,066 (E) 72139141Bars and rods, hot-rolled, of iron or non-alloy steel, in irregularly wound coils, containing by weight ≤ 0,06 % of carbon, of circular cross-section measuring < 14 mm in diameter (excl. free-cutting steel, bars and rods, hot-rolled, for concrete reinforcement and tyre cord, and bars and rods, hot-rolled, containing indentations, ribs, grooves or other deformations produced during the rolling process)0,038 1,364 (C) 0,475 (D) 0,066 (E) 72139149Bars and rods, hot-rolled, of iron or non-alloy steel, in irregularly wound coils, containing by weight > 0,06 % and < 0,25 % of carbon, of circular cross-section, measuring < 14 mm in diameter (excl. of free-cutting steel, bars and rods, hot-rolled, for concrete reinforcement and tyre cord and bars and rods, hot-rolled, containing indentations, ribs, grooves or other deformations produced during the rolling process)0,038

1,364 (C) 0,475 (D) 0,066 (E) 72139170Bars and rods, hot-rolled, in irregularly wound coils, of iron or non-alloy steel, containing by weight ≥ 0,25 % but ≤ 0,75 % carbon, of circular cross-section measuring < 14 mm in diameter (excl. of free-cutting steel, and bars and rods, smooth, for concrete reinforcement and tyre cord, and bars and rods with indentations, ribs, grooves or other deformations produced during the rolling process)0,038 1,364 (C) 0,475 (D) 0,066 (E) 72139190Bars and rods, hot-rolled, of iron or non-alloy steel, in irregularly wound coils, containing by weight > 0,75 % of carbon, of circular cross-section measuring < 14 mm in diameter (excl. of free-cutting steel, bars and rods, smooth, for tyre cord and bars and rods with indentations, ribs, grooves and other deformations produced during the rolling process)0,038 1,364 (C) 0,475 (D) 0,066 (E) 72139910Bars and rods, of iron or non-alloy steel, hot-rolled, in irregularly wound coils, containing by weight < 0,25 % carbon (excl. products of circular cross-section measuring < 14 mm in diameter, bars and rods of free-cutting steel, and bars and rods with indentations, ribs, grooves or other deformations produced during the rolling process)0,038 1,364 (C) 0,475 (D) 0,066 (E) 72139990Bars and rods, hot-rolled, in irregularly wound coils, of iron or non-alloy steel, containing by weight ≥ 0,25 % carbon (excl. products of circular cross-section measuring < 14 mm diameter, bars and rods of free-cutting steel, and bars and rods with indentations, ribs, grooves or other deformations produced during the rolling process)0,038 1,364 (C) 0,475 (D) 0,066 (E) 72141000Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils)0,303 1,629 (C) 0,740 (D) 0,331 (E) 72142000Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process0,038 1,364 (C) 0,475 (D) 0,066 (E) 72143000Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling)0,038 1,364 (C) 0,475 (D) 0,066 (E) 72149110Bars and rods of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, containing by weight < 0,25 % of carbon, of rectangular other than square cross-section (excl. those with indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling, and free-cutting steel)0,038 1,364 (C) 0,475 (D) 0,066 (E) 72149190Other bars and rods of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded, containing by weight ≥ 0,25 % of carbon, of rectangular other than square cross-section (excl. those with indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling, and free-cutting steel)0,038

1,364 (C) 0,475 (D) 0,066 (E) 72149910Bars and rods of the type used for concrete reinforcement, smooth, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded, containing < 0,25 % of carbon, of square cross-section or of a cross-section other than rectangular0,038 1,364 (C) 0,475 (D) 0,066 (E) 72149931Bars and rods of iron or non-alloy steel, only hot-rolled, hot-drawn or hot-extruded, containing < 0,25 % of carbon, of circular cross-section, of a maximum diameter of ≥ 80 mm (other than of free-cutting steel, smooth bars and rods, for reinfoced concrete, or bars and rods containing indentations, ribs, grooves or other deformations produced during the rolling process, or wound after rolling)0,038 1,364 (C) 0,475 (D) 0,066 (E) 72149939Bars and rods of iron or non-alloy steel, only hot-rolled, hot-drawn or hot-extruded, containing < 0,25 % of carbon, of circular cross-section of a maximum diameter of < 80 mm (other than of free-cutting steel, smooth bars and rods, for reinforced concrete, or bars and rods containing indentations, ribs, grooves or other deformations produced during the rolling process, or wound after rolling)0,038 1,364 (C) 0,475 (D) 0,066 (E) 72149950Bars and rods of iron or non-alloy steel, only hot-rolled, hot-drawn or hot-extruded, containing by weight < 0,25 % of carbon, of square cross-section or of a cross-section other than square or circular (other than of free-cutting steel, smooth bars and rods, for reinforced concrete, or bars and rods containing indentations, ribs, grooves or other deformations produced during the rolling process, or wound after rolling)0,038 1,364 (C) 0,475 (D) 0,066 (E) 72149971Bars and rods of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded, containing by weight ≥ 0,25 % carbon, of circular cross-section measuring ≥ 80 mm in diameter (excl. bars and rods with indentations, ribs, grooves or other deformations produced during the rolling process, twisted after rolling, and of free-cutting steel)0,038 1,364 (C) 0,475 (D) 0,066 (E) 72149979Bars and rods of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded, containing by weight ≥ 0,25 % carbon, of circular cross-section measuring < 80 mm in diameter (excl. bars and rods with indentations, ribs, grooves or other deformations produced during the rolling process, twisted after rolling, and of free-cutting steel)0,038 1,364 (C) 0,475 (D) 0,066 (E) 72149995Bars and rods of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded, containing by weight ≥ 0,25 % carbon, of square or of other than rectangular or circular cross-section (excl. indentations, ribs, grooves or other deformations produced during the rolling process, twisted fter rolling, and of free-cutting steel)0,038 1,364 (C) 0,475 (D) 0,066 (E) 72151000Bars and rods, of non-alloy free-cutting steel, not further worked than cold-formed or cold-finished0,038 1,364 (C) 0,475 (D) 0,066 (E) 72155011Other bars and rods of iron or non-alloy steel, not further worked than cold-formed or cold-finished, containing by weight < 0,25 % of carbon of rectangular other than square cross-section (excl. those of free-cutting steel)0,038

1,364 (C) 0,475 (D) 0,066 (E) 72155019Other bars and rods of iron or non-alloy steel, not further worked than cold-formed or cold-finished, containing by weight < 0,25 % of carbon, of square or other than rectangular cross-section (excl. those of free-cutting steel)0,038 1,364 (C) 0,475 (D) 0,066 (E) 72155080Other bars and rods of iron or non-alloy steel, not further worked than cold-formed or cold-finished, containing by weight ≥ 0,25 % of carbon (excl. those of free-cutting steel)0,038 1,364 (C) 0,475 (D) 0,066 (E) 72159000Bars or rods, of iron or non-alloy steel, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s.0,038 1,364 (C) 0,475 (D) 0,066 (E) 72161000U, I or H sections of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or extruded, of a height of < 80 mm0,038 1,364 (C) 0,475 (D) 0,066 (E) 72162100L sections of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or extruded, of a height of < 80 mm0,038 1,364 (C) 0,475 (D) 0,066 (E) 72162200T sections of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or extruded, of a height of < 80 mm0,038 1,364 (C) 0,475 (D) 0,066 (E) 72163110U sections of iron or non-alloy steel, simply hot-rolled, hot-drawn or extruded, of a height ≥ 80 mm but ≤ 220 mm0,038 1,364 (C) 0,475 (D) 0,066 (E) 72163190U sections of iron or non-alloy steel, simply hot-rolled, hot-drawn or extruded, of a height > 220 mm0,038 1,364 (C) 0,475 (D) 0,066 (E) 72163211I sections with parallel flange faces, of iron or non-alloy steel, simply hot-rolled, hot-drawn or extruded, of a height ≥ 80 mm but ≤ 220 mm0,038 1,364 (C) 0,475 (D) 0,066 (E) 72163219I sections of iron or non-alloy steel, simply hot-rolled, hot-drawn or extruded, of a height ≥ 80 mm but ≤ 220 mm (excl. 7216.32.11)0,038 1,364 (C) 0,475 (D) 0,066 (E) 72163291I sections with parallel flange faces, of iron or non-alloy steel, simply hot-rolled, hot-drawn or extruded, of a height > 220 mm0,038 1,364 (C) 0,475 (D) 0,066 (E) 72163299I sections of iron or non-alloy steel, simply hot-rolled, hot-drawn or extruded, of a height > 220 mm (excl. 7216.32.91)0,038 1,364 (C) 0,475 (D) 0,066 (E) 72163310H sections of iron or non-alloy steel, simply hot-rolled, hot-drawn or extruded, of a height ≥ 80 mm but ≤ 180 mm0,038 1,364 (C) 0,475 (D) 0,066 (E) 72163390H sections of iron or non-alloy steel, simply hot-rolled, hot-drawn or extruded, of a height > 180 mm0,038 1,364 (C) 0,475 (D) 0,066 (E) 72164010L sections of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or extruded, of a height of ≥ 80 mm0,038 1,364 (C) 0,475 (D) 0,066 (E) 72164090T sections of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or extruded, of a height of ≥ 80 mm0,038 1,364 (C) 0,475 (D) 0,066 (E) 72165010Sections of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, with a cross-section which is capable of being enclosed in a square the side of which is ≤ 80 mm (excl. U, I, H, L or T sections)0,038

1,364 (C) 0,475 (D) 0,066 (E) 72165091Bulb sections bulb flat, only hot-rolled, hot-drawn or hot-extruded0,038 1,364 (C) 0,475 (D) 0,066 (E) 72165099Profile of iron or non-alloy steel, only hot-rolled, hot-drawn or hot-extruded (other than with a cross-section which is capable of being enclosed in a square the side of which is ≤ 80 mm, and U-, I-, H-, L- or T-sections and ribbed sections [ribbed steel])0,038 1,364 (C) 0,475 (D) 0,066 (E) 72166110c, l, u, z, omega or open-ended sections of iron or non-alloy steel, simply cold-formed or cold-finished, obtained from flat-rolled products0,038 1,364 (C) 0,475 (D) 0,066 (E) 72166190Angles, shapes and sections (other than c, l, u, z, omega or open-ended sections) of iron or non-alloy steel, simply cold-formed or cold-finished, obtained from flat-rolled products0,038 1,364 (C) 0,475 (D) 0,066 (E) 72166900Angles, shapes and sections, of iron or non-alloy steel, not further worked than cold-formed or cold-finished (excl. profiled sheet)0,038 1,364 (C) 0,475 (D) 0,066 (E) 72169110Sheets of iron or non-alloy steel, cold-formed or cold finished, profiled ribbed0,038 1,364 (C) 0,475 (D) 0,066 (E) 72169180Angles, shapes and sections, of iron or non-alloy steel, cold-formed or cold-finished from flat-rolled products and further worked (excl. profiled sheet)0,038 1,364 (C) 0,475 (D) 0,066 (E) 72169900Angles, shapes and sections, of iron or non-alloy steel, cold-formed or cold-finished and further worked, or hot-forged, or hot-formed by other means and further worked, n.e.s. (excl. from flat-rolled products)0,038 1,364 (C) 0,475 (D) 0,066 (E) 72171010Wire of iron or non-alloy steel, in coils, containing by weight < 0,25 % carbon, not plated or coated, whether or not polished, with a maximum cross-sectional dimension of < 0,8 mm0,038 1,364 (C) 0,475 (D) 0,066 (E) 72171031Wire of iron or non-alloy steel, in coils, containing by weight < 0,25 % carbon, with indentations, ribs, grooves or other deformations produced during the rolling process, not plated or coated, with a maximum cross-sectional dimension of ≥ 0,8 mm0,038 1,364 (C) 0,475 (D) 0,066 (E) 72171039Wire of iron or non-alloy steel, in coils, containing by weight < 0,25 % carbon, not plated or coated, with a maximum cross-sectional dimension of ≥ 0,8 mm (without indentations, ribs, grooves or other deformations produced during the rolling process)0,038 1,364 (C) 0,475 (D) 0,066 (E) 72171050Wire of iron or non-alloy steel, in coils, containing by weight ≥ 0,25 % but < 0,6 % carbon, not plated or coated, whether or not polished (excl. hot-rolled bars and rods)0,038 1,364 (C) 0,475 (D) 0,066 (E) 72171090Wire of iron or non-alloy steel, in coils, containing by weight ≥ 0,6 % carbon, not plated or coated, whether or not polished (excl. hot-rolled bars and rods)0,038 1,364 (C) 0,475 (D) 0,066 (E) 72172010Wire of iron or non-alloy steel, in coils, containing by weight < 0,25 % carbon, plated or coated with zinc, with a maximum cross-sectional dimension of < 0,8 mm0,071

1,397 (C) 0,508 (D) 0,099 (E) 72172030Wire of iron or non-alloy steel, in coils, containing by weight < 0,25 % carbon, plated or coated with zinc, with a maximum cross-sectional dimension of < 0,8 mm (excl. bars and rods)0,071 1,397 (C) 0,508 (D) 0,099 (E) 72172050Wire of iron or non-alloy steel, in coils, containing by weight ≥ 0,25 % but < 0,6 % carbon, plated or coated with zinc (excl. bars and rods)0,071 1,397 (C) 0,508 (D) 0,099 (E) 72172090Wire of iron or non-alloy steel, in coils, containing by weight ≥ 0,6 % carbon, plated or coated with zinc (excl. bars and rods)0,071 1,397 (C) 0,508 (D) 0,099 (E) 72173041Wire of iron or non-alloy steel, in coils, containing by weight < 0,25 % carbon, copper-coated (excl. bars and rods)0,071 1,397 (C) 0,508 (D) 0,099 (E) 72173049Wire of iron or non-alloy steel, in coils, containing by weight < 0,25 % carbon, plated or coated with base metals (excl. products plated or coated with zinc or copper and bars and rods)0,071 1,397 (C) 0,508 (D) 0,099 (E) 72173050Wire of iron or non-alloy steel, in coils, containing by weight ≥ 0,25 % but < 0,6 % carbon, plated or coated with base metals (excl. products plated or coated with zinc, and bars and rods)0,071 1,397 (C) 0,508 (D) 0,099 (E) 72173090Wire of iron or non-alloy steel, in coils, containing by weight ≥ 0,6 % carbon, plated or coated with base metals (excl. products plated or coated with zinc, and bars and rods)0,071 1,397 (C) 0,508 (D) 0,099 (E) 72179020Wire of iron or non-alloy steel, in coils, containing by weight < 0,25 % carbon, plated or coated (excl. products plated or coated with base metals and bars and rods)0,071 1,397 (C) 0,508 (D) 0,099 (E) 72179050Wire of iron or non-alloy steel, in coils, containing by weight ≥ 0,25 % but < 0,6 % carbon, plated or coated (excl. products plated or coated with with base metals, and bars and rods)0,071 1,397 (C) 0,508 (D) 0,099 (E) 72179090Wire of iron or non-alloy steel, in coils, containing by weight ≥ 0,6 % carbon, plated or coated (excl. products plated or coated with base metals, and bars and rods)0,071 1,397 (C) 0,508 (D) 0,099 (E) 72181000Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting)0,358 1,419 (1) 1,381 (2) 72189110Semi-finished products of stainless steel, of rectangular other than square cross-section, containing by weight ≥ 2,5 % nickel0,128 1,189 (1) 1,151 (2) 72189180Semi-finished products of stainless steel, of rectangular other than square cross-section, containing by weight < 2,5 nickel0,128 1,189 (1) 1,151 (2) 72189911Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting0,128 1,189 (1) 1,151 (2) 72189919Semi-finished products of stainless steel, of square cross-section, forged0,358 1,419 (1) 1,381 (2) 72189920Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting0,128

1,189 (1) 1,151 (2) 72189980Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section)0,358 1,419 (1) 1,381 (2) 72191100Flat-rolled products of stainless steel, of a width of ≥ 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm0,073 1,189 (1) 1,151 (2) 72191210Flat-rolled products of stainless steel, of a width of ≥ 600 mm, not further worked than hot-rolled, in coils, of a thickness of ≥ 4,75 mm but ≤ 10 mm, containing by weight ≥ 2,5 nickel0,073 1,189 (1) 1,151 (2) 72191290Flat-rolled products of stainless steel, of a width of ≥ 600 mm, not further worked than hot-rolled, in coils, of a thickness of ≥ 4,75 mm but ≤ 10 mm, containing by weight < 2,5 nickel0,073 1,189 (1) 1,151 (2) 72191310Flat-rolled products of stainless steel, of a width of ≥ 600 mm, not further worked than hot-rolled, in coils, of a thickness of ≥ 3 mm but ≤ 4,75 mm, containing by weight ≥ 2,5 nickel0,073 1,189 (1) 1,151 (2) 72191390Flat-rolled products of stainless steel, of a width of ≥ 600 mm, not further worked than hot-rolled, in coils, of a thickness of ≥ 3 mm but ≤ 4,75 mm, containing by weight < 2,5 nickel0,073 1,189 (1) 1,151 (2) 72191410Flat-rolled products of stainless steel, of a width of ≥ 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm, containing by weight ≥ 2,5 nickel0,073 1,189 (1) 1,151 (2) 72191490Flat-rolled products of stainless steel, of a width of ≥ 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm, containing by weight < 2,5 nickel0,073 1,189 (1) 1,151 (2) 72192110Flat-rolled products of stainless steel, of a width of ≥ 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm, containing by weight ≥ 2,5 nickel0,073 1,189 (1) 1,151 (2) 72192190Flat-rolled products of stainless steel, of a width of ≥ 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm, containing by weight < 2,5 nickel0,073 1,189 (1) 1,151 (2) 72192210Flat-rolled products of stainless steel, of a width of ≥ 600 mm, not further worked than hot-rolled, not in coils, of a thickness of ≥ 4,75 mm but ≤ 10 mm, containing by weight ≥ 2,5 % nickel0,073 1,189 (1) 1,151 (2) 72192290Flat-rolled products of stainless steel, of a width of ≥ 600 mm, not further worked than hot-rolled, not in coils, of a thickness of ≥ 4,75 mm but ≤ 10 mm, containing by weight < 2,5 % nickel0,073 1,189 (1) 1,151 (2) 72192300Flat-rolled products of stainless steel, of a width of ≥ 600 mm, not further worked than hot-rolled, not in coils, of a thickness of ≥ 3 mm and < 4,75 mm0,073 1,189 (1) 1,151 (2) 72192400Flat-rolled products of stainless steel, of a width of ≥ 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm0,073 1,189 (1) 1,151 (2) 72193100Flat-rolled products of stainless steel, of a width of ≥ 600 mm, not further worked than cold-rolled cold-reduced, of a thickness of ≥ 4,75 mm0,109 1,270 (1)

1,230 (2) 72193210Flat-rolled products of stainless steel, of a width of ≥ 600 mm, not further worked than cold-rolled cold-reduced, of a thickness of ≥ 3 mm but ≤ 4,75 mm, containing by weight ≥ 2,5 % nickel0,109 1,270 (1) 1,230 (2) 72193290Flat-rolled products of stainless steel, of a width of ≥ 600 mm, not further worked than cold-rolled cold-reduced, of a thickness of ≥ 3 mm but ≤ 4,75 mm, containing by weight < 2,5 % nickel0,109 1,270 (1) 1,230 (2) 72193310Flat-rolled products of stainless steel, of a width of ≥ 600 mm, not further worked than cold-rolled cold-reduced, of a thickness of > 1 mm but < 3 mm, containing by weight ≥ 2,5 % nickel0,109 1,270 (1) 1,230 (2) 72193390Flat-rolled products of stainless steel, of a width of ≥ 600 mm, not further worked than cold-rolled cold-reduced, of a thickness of > 1 mm but < 3 mm, containing by weight < 2,5 % nickel0,109 1,270 (1) 1,230 (2) 72193410Flat-rolled products of stainless steel, of a width of ≥ 600 mm, not further worked than cold-rolled cold-reduced, of a thickness of ≥ 0,5 mm but ≤ 1 mm, containing by weight ≥ 2,5 % nickel0,109 1,270 (1) 1,230 (2) 72193490Flat-rolled products of stainless steel, of a width of ≥ 600 mm, not further worked than cold-rolled cold-reduced, of a thickness of ≥ 0,5 mm but ≤ 1 mm, containing by weight < 2,5 % nickel0,109 1,270 (1) 1,230 (2) 72193510Flat-rolled products of stainless steel, of a width of ≥ 600 mm, not further worked than cold-rolled cold-reduced, of a thickness of < 0,5 mm, containing by weight ≥ 2,5 % nickel0,109 1,270 (1) 1,230 (2) 72193590Flat-rolled products of stainless steel, of a width of ≥ 600 mm, not further worked than cold-rolled cold-reduced, of a thickness of < 0,5 mm, containing by weight < 2,5 % nickel0,109 1,270 (1) 1,230 (2) 72199020Flat-rolled products of stainless steel, of a width of ≥ 600 mm, hot-rolled or cold-rolled cold-reduced and further worked, perforated0,109 1,270 (1) 1,230 (2) 72199080Flat-rolled products of stainless steel, of a width of ≥ 600 mm, hot-rolled or cold-rolled cold-reduced and further worked, non-perforated0,109 1,270 (1) 1,230 (2) 72201100Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of ≥ 4,75 mm0,073 1,189 (1) 1,151 (2) 72201200Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm0,073 1,189 (1) 1,151 (2) 72202021Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled cold-reduced, of a thickness of ≥ 3 mm and containing by weight ≥ 2,5 % nickel0,109 1,270 (1) 1,230 (2) 72202029Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled cold-reduced, of a thickness of ≥ 3 mm and containing by weight < 2,5 % nickel0,109 1,270 (1) 1,230 (2) 72202041Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled cold-reduced, of a thickness of > 0,35 mm but < 3 mm, and containing by weight ≥ 2,5 % nickel0,109

1,270 (1) 1,230 (2) 72202049Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled cold-reduced, of a thickness of > 0,35 mm but < 3 mm, and containing by weight < 2,5 % nickel0,109 1,270 (1) 1,230 (2) 72202081Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled cold-reduced, of a thickness of ≤ 0,35 mm and containing by weight ≥ 2,5 % nickel0,109 1,270 (1) 1,230 (2) 72202089Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled cold-reduced, of a thickness of ≤ 0,35 mm and containing by weight < 2,5 % nickel0,109 1,270 (1) 1,230 (2) 72209020Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled cold-reduced and further worked, perforated0,109 1,270 (1) 1,230 (2) 72209080Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled cold-reduced and further worked, non-perforated0,109 1,270 (1) 1,230 (2) 72210010Bars and rods of stainless steel, hot-rolled, in irregularly wound coils, containing by weight ≥ 2,5 % nickel0,109 1,225 (1) 1,187 (2) 72210090Bars and rods of stainless steel, hot-rolled, in irregularly wound coils, containing by weight < 2,5 % nickel0,109 1,225 (1) 1,187 (2) 72221111Bars and rods of stainless steel, not further worked than hot-rolled, hot-drawn or extruded, of circular cross-section of a diameter of ≥ 800 mm, containing by weight ≥ 2,5 % nickel0,109 1,225 (1) 1,187 (2) 72221119Bars and rods of stainless steel, not further worked than hot-rolled, hot-drawn or extruded, of circular cross-section of a diameter of ≥ 800 mm, containing by weight < 2,5 % nickel0,109 1,225 (1) 1,187 (2) 72221181Bars and rods of stainless steel, not further worked than hot-rolled, hot-drawn or extruded, of circular cross-section measuring < 80 mm and containing by weight ≥ 2,5 % nickel0,109 1,225 (1) 1,187 (2) 72221189Bars and rods of stainless steel, not further worked than hot-rolled, hot-drawn or extruded, of circular cross-section measuring < 80 mm and containing by weight < 2,5 % nickel0,109 1,225 (1) 1,187 (2) 72221910Bars and rods of stainless steel, not further worked than hot-rolled, hot-drawn or extruded, containing by weight ≥ 2,5 % nickel (excl. such products of circular cross-section)0,109 1,225 (1) 1,187 (2) 72221990Bars and rods of stainless steel, not further worked than hot-rolled, hot-drawn or extruded, containing by weight < 2,5 % nickel (excl. such products of circular cross-section)0,109 1,225 (1) 1,187 (2) 72222011Bars and rods of stainless steel, of circular cross-section of a diameter ≥ 80 mm, simply cold-formed or cold-finished, containing by weight ≥ 2,5 % nickel0,109 1,225 (1) 1,187 (2) 72222019Bars and rods of stainless steel, of circular cross-section of a diameter ≥ 80 mm, simply cold-formed or cold-finished, containing by weight < 2,5 % nickel0,109 1,225 (1) 1,187 (2) 72222021Bars and rods of stainless steel, not further worked than cold-formed or cold-finished, of circular cross-section measuring ≥ 25 mm but < 80 mm and containing by weight ≥ 2,5 % nickel0,109

1,225 (1) 1,187 (2) 72222029Bars and rods of stainless steel, not further worked than cold-formed or cold-finished, of circular cross-section measuring ≥ 25 mm but < 80 mm and containing by weight < 2,5 % nickel0,109 1,225 (1) 1,187 (2) 72222031Bars and rods of stainless steel, not further worked than cold-formed or cold-finished, of circular cross-section measuring < 25 mm and containing by weight ≥ 2,5 % nickel0,109 1,225 (1) 1,187 (2) 72222039Bars and rods of stainless steel, not further worked than cold-formed or cold-finished, of circular cross-section measuring < 25 mm and containing by weight < 2,5 % nickel0,109 1,225 (1) 1,187 (2) 72222081Bars and rods of stainless steel, not further worked than cold-formed or cold-finished, containing by weight ≥ 2,5 % nickel (excl. such products of circular cross-section)0,109 1,225 (1) 1,187 (2) 72222089Bars and rods of stainless steel, not further worked than cold-formed or cold-finished, containing by weight < 2,5 % nickel (excl. such products of circular cross-section)0,109 1,225 (1) 1,187 (2) 72223051Other bars and rods of stainless steel, containing by weight ≥ 2,5 % of nickel, forged0,303 1,419 (1) 1,381 (2) 72223091Other bars and rods of stainless steel, containing by weight < 2,5 % of nickel, forged0,303 1,419 (1) 1,381 (2) 72223097Bars and rods of stainless steel, cold-formed or cold-finished and further worked, or hot-formed and further worked, n.e.s. (excl. forged products)0,303 1,419 (1) 1,381 (2) 72224010Angles, shapes and sections of stainless steel, only hot-rolled, only hot-drawn or only extruded0,109 1,225 (1) 1,187 (2) 72224050Angles, shapes and sections of stainless steel, not further worked than cold-formed or cold-finished0,109 1,225 (1) 1,187 (2) 72224090Angles, shapes and sections of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s.0,109 1,225 (1) 1,187 (2) 72230011Wire of stainless steel, in coils, containing by weight 28 % to 31 % nickel and 20 % to 22 % chromium (excl. bars and rods)0,109 1,225 (1) 1,187 (2) 72230019Wire of stainless steel, in coils, containing by weight ≥ 2,5 % nickel (excl. such products containing 28 % to 31 % nickel and 20 % to 22 % chromium, and bars and rods)0,109 1,225 (1) 1,187 (2) 72230091Wire of stainless steel, in coils, containing by weight < 2,5 % nickel, 13 % to 25 % chromium and 3,5 % to 6 % aluminium (excl. bars and rods)0,109 1,225 (1) 1,187 (2) 72230099Wire of stainless steel, in coils, containing by weight < 2,5 % nickel (excl. such products containing 13 % to 25 % chromium and 3,5 % to 6 % aluminium, and bars and rods)0,109 1,225 (1) 1,187 (2) 72241010Ingots and other primary forms, of tool steel 0,453 (F) 0,330 (G) 0,330 (H) 0,358 (J) 1,807 (F)(1) 0,982 (G)(1) 0,640 (H)(1) 1,180 (J)(1) 1,640 (F)(2) 0,969 (G)(2) 0,628 (H)(2) 1,148 (J)(2) 72241090Steel, alloy, other than stainless, in ingots or other primary forms (excl. of tool steel, waste and scrap in ingot form and products obtained by continuous casting)

0,453 (F) 0,330 (G) 0,330 (H) 0,358 (J) 1,807 (F)(1) 0,982 (G)(1) 0,640 (H)(1) 1,180 (J)(1) 1,640 (F)(2) 0,969 (G)(2) 0,628 (H)(2) 1,148 (J)(2) 72249002Semi-finished products of tool steel 0,223 (F) 0,100 (G) 0,100 (H) 0,128 (J) 1,577 (F)(1) 0,752 (G)(1) 0,410 (H)(1) 0,950 (J)(1) 1,409 (F)(2) 0,739 (G)(2) 0,397 (H)(2) 0,918 (J)(2) 72249003Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 0,223 (F) 0,100 (G) 0,100 (H) 0,128 (J) 1,577 (F)(1) 0,752 (G)(1) 0,410 (H)(1) 0,950 (J)(1) 1,409 (F)(2) 0,739 (G)(2) 0,397 (H)(2) 0,918 (J)(2) 72249005Semi-finished products of steel containing by weight ≤ 0,7 % of carbon, 0,5 % to 1,2 % of manganese, 0,6 % to 2,3 % of silicon, or of steel containing by weight ≥ 0,0008 % of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 0,223 (F) 0,100 (G) 0,100 (H) 0,128 (J) 1,577 (F)(1) 0,752 (G)(1) 0,410 (H)(1) 0,950 (J)(1) 1,409 (F)(2) 0,739 (G)(2) 0,397 (H)(2) 0,918 (J)(2) 72249007Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 72249005) 0,223 (F) 0,100 (G) 0,100 (H) 0,128 (J) 1,577 (F)(1) 0,752 (G)(1) 0,410 (H)(1) 0,950 (J)(1) 1,409 (F)(2) 0,739 (G)(2) 0,397 (H)(2) 0,918 (J)(2) 72249014Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring ≥ twice the thickness (excl. of tool steel) 0,223 (F) 0,100 (G) 0,100 (H) 0,128 (J) 1,577 (F)(1) 0,752 (G)(1) 0,410 (H)(1) 0,950 (J)(1) 1,409 (F)(2) 0,739 (G)(2) 0,397 (H)(2) 0,918 (J)(2) 72249018Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 0,453 (F) 0,330 (G) 0,330 (H) 0,358 (J) 1,807 (F)(1) 0,982 (G)(1) 0,640 (H)(1) 1,180 (J)(1) 1,640 (F)(2) 0,969 (G)(2) 0,628 (H)(2) 1,148 (J)(2) 72249031Semi-finished products of steel containing by weight 0,9 % to 1,15 % carbon, 0,5 % to 2 % of chromium and, if present, ≤ 0,5 % of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 0,223 (F) 0,100 (G) 0,100 (H) 0,128 (J) 1,577 (F)(1) 0,752 (G)(1) 0,410 (H)(1) 0,950 (J)(1) 1,409 (F)(2) 0,739 (G)(2) 0,397 (H)(2) 0,918 (J)(2) 72249038Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9 % to 1,15 % of carbon, 0,5 % to 2 % of chromium and, if present, ≤ 0,5 % of molybdenum) 0,223 (F) 0,100 (G)

0,100 (H) 0,128 (J) 1,577 (F)(1) 0,752 (G)(1) 0,410 (H)(1) 0,950 (J)(1) 1,409 (F)(2) 0,739 (G)(2) 0,397 (H)(2) 0,918 (J)(2) 72249090Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 0,453 (F) 0,330 (G) 0,330 (H) 0,358 (J) 1,807 (F)(1) 0,982 (G)(1) 0,640 (H)(1) 1,180 (J)(1) 1,640 (F)(2) 0,969 (G)(2) 0,628 (H)(2) 1,148 (J)(2) 72251100Flat-rolled products of silicon-electrical steel, of a width of ≥ 600 mm, grain-oriented0,073 1,779 (C) 0,635 (D) 0,109 (E) 72251910Flat-rolled products of silicon-electrical steel, of a width of ≥ 600 mm, hot-rolled0,073 1,399 (C) 0,510 (D) 0,101 (E) 72251990Flat-rolled products of silicon-electrical steel, of a width of ≥ 600 mm, cold-rolled cold-reduced, non-grain-oriented0,109 1,488 (C) 0,563 (D) 0,138 (E) 72253010Flat-rolled products of tool steel, of a width of ≥ 600 mm, not further worked than hot-rolled, in coils0,073 1,577 (F)(1) 0,752 (G)(1) 0,410 (H)(1) 0,950 (J)(1) 1,409 (F)(2) 0,739 (G)(2) 0,397 (H)(2) 0,918 (J)(2) 72253030Flat-rolled products of high-speed steel, of a width of ≥ 600 mm, not further worked than hot-rolled, in coils0,073 1,577 (F)(1) 0,752 (G)(1) 0,410 (H)(1) 0,950 (J)(1) 1,409 (F)(2) 0,739 (G)(2) 0,397 (H)(2) 0,918 (J)(2) 72253090Flat-rolled products of alloy steel other than stainless, of a width of ≥ 600 mm, not further worked than hot-rolled, in coils (excl. products of tool steel, high-speed steel or silicon-electrical steel)0,073 1,577 (F)(1) 0,752 (G)(1) 0,410 (H)(1) 0,950 (J)(1) 1,409 (F)(2) 0,739 (G)(2) 0,397 (H)(2) 0,918 (J)(2) 72254012Flat-rolled products of tool steel, of a width of ≥ 600 mm, not further worked than hot-rolled, not in coils0,073 1,577 (F)(1) 0,752 (G)(1) 0,410 (H)(1) 0,950 (J)(1) 1,409 (F)(2) 0,739 (G)(2) 0,397 (H)(2) 0,918 (J)(2) 72254015Flat-rolled products of high-speed steel, of a width of ≥ 600 mm, not further worked than hot-rolled, not in coils0,073 1,577 (F)(1) 0,752 (G)(1) 0,410 (H)(1) 0,950 (J)(1) 1,409 (F)(2) 0,739 (G)(2) 0,397 (H)(2) 0,918 (J)(2) 72254040Flat-rolled products of alloy steel other than stainless, of a width of ≥ 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm (excl. products of tool steel, high-speed steel or silicon-electrical steel)0,073 1,577 (F)(1) 0,752 (G)(1) 0,410 (H)(1) 0,950 (J)(1) 1,409 (F)(2) 0,739 (G)(2) 0,397 (H)(2) 0,918 (J)(2) 72254060Flat-rolled products of alloy steel other than stainless, of a width of ≥ 600 mm, not further worked than hot-rolled, not in coils, of a thickness of ≥ 4,75 mm but ≤ 10 mm (excl. products of tool steel, high-speed steel or silicon-electrical steel)0,073 1,577 (F)(1) 0,752 (G)(1) 0,410 (H)(1) 0,950 (J)(1) 1,409 (F)(2) 0,739 (G)(2) 0,397 (H)(2) 0,918 (J)(2) 72254090Flat-rolled products of alloy steel other than stainless, of a width of ≥ 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 4,75 mm (excl. products of tool steel, high-speed steel or silicon-electrical steel)0,073

1,577 (F)(1) 0,752 (G)(1) 0,410 (H)(1) 0,950 (J)(1) 1,409 (F)(2) 0,739 (G)(2) 0,397 (H)(2) 0,918 (J)(2) 72255020Flat-rolled products of high-speed steel, of a width of ≥ 600 mm, not further worked than cold-rolled cold-reduced0,109 1,673 (F)(1) 0,815 (G)(1) 0,460 (H)(1) 1,021 (J)(1) 1,499 (F)(2) 0,801 (G)(2) 0,446 (H)(2) 0,987 (J)(2) 72255080Flat-rolled products of alloy steel other than stainless, of a width of ≥ 600 mm, not further worked than cold-rolled cold-reduced (excl. products of high-speed steel or silicon-electrical steel)0,109 1,673 (F)(1) 0,815 (G)(1) 0,460 (H)(1) 1,021 (J)(1) 1,499 (F)(2) 0,801 (G)(2) 0,446 (H)(2) 0,987 (J)(2) 72259100Flat-rolled products of alloy steel other than stainless, of a width of ≥ 600 mm, hot-rolled or cold-rolled cold-reduced and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel)0,142 1,706 (F)(1) 0,848 (G)(1) 0,493 (H)(1) 1,054 (J)(1) 1,532 (F)(2) 0,835 (G)(2) 0,480 (H)(2) 1,021 (J)(2) 72259200Flat-rolled products of alloy steel other than stainless, of a width of ≥ 600 mm, hot-rolled or cold-rolled cold-reduced and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel)0,142 1,706 (F)(1) 0,848 (G)(1) 0,493 (H)(1) 1,054 (J)(1) 1,532 (F)(2) 0,835 (G)(2) 0,480 (H)(2) 1,021 (J)(2) 72259900Flat-rolled products of alloy steel other than stainless, of a width of ≥ 600 mm, hot-rolled or cold-rolled cold-reduced and further worked (excl. plated or coated with zinc and products of silicon-electrical steel)0,142 1,706 (F)(1) 0,848 (G)(1) 0,493 (H)(1) 1,054 (J)(1) 1,532 (F)(2) 0,835 (G)(2) 0,480 (H)(2) 1,021 (J)(2) 72261100Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled cold-reduced, grain-oriented0,073 1,779 (C) 0,635 (D) 0,109 (E) 72261910Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled0,073 1,399 (C) 0,510 (D) 0,101 (E) 72261980Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled cold-reduced, whether or not further worked, or hot-rolled and further worked, non-grain-oriented0,109 1,488 (C) 0,563 (D) 0,138 (E) 72262000Flat-rolled products of high-speed steel, of a width of ≤ 600 mm, hot-rolled or cold-rolled cold-reduced0,073 1,577 (F)(1) 0,752 (G)(1) 0,410 (H)(1) 0,950 (J)(1) 1,409 (F)(2) 0,739 (G)(2) 0,397 (H)(2) 0,918 (J)(2) 72269120Flat-rolled products of tool steel, of a width of < 600 mm, simply hot-rolled0,073 1,577 (F)(1) 0,752 (G)(1) 0,410 (H)(1) 0,950 (J)(1) 1,409 (F)(2) 0,739 (G)(2) 0,397 (H)(2) 0,918 (J)(2) 72269191Flat-rolled products of alloy steel other than stainless steel, simply hot-rolled, of a thickness of ≥ 4,75 mm, of a width of < 600 mm (excl. of tool steel, silicon-electrical steel or high speed steel)0,073 1,577 (F)(1) 0,752 (G)(1) 0,410 (H)(1) 0,950 (J)(1) 1,409 (F)(2) 0,739 (G)(2) 0,397 (H)(2) 0,918 (J)(2) 72269199Flat-rolled products of alloy steel other than stainless steel, simply hot-rolled, of a thickness of < 4,75 mm, of a width of < 600 mm (excl. of tool steel, silicon-electrical steel or high speed steel)0,073

1,577 (F)(1) 0,752 (G)(1) 0,410 (H)(1) 0,950 (J)(1) 1,409 (F)(2) 0,739 (G)(2) 0,397 (H)(2) 0,918 (J)(2) 72269200Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled cold-reduced (excl. products of high-speed steel or silicon-electrical steel)0,109 1,673 (F)(1) 0,815 (G)(1) 0,460 (H)(1) 1,021 (J)(1) 1,499 (F)(2) 0,801 (G)(2) 0,446 (H)(2) 0,987 (J)(2) 72269910Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled cold-reduced and electrolytically plated or coated with zinc (excl. products of high-speed steel or silicon-electrical steel)0,142 1,706 (F)(1) 0,848 (G)(1) 0,493 (H)(1) 1,054 (J)(1) 1,532 (F)(2) 0,835 (G)(2) 0,480 (H)(2) 1,021 (J)(2) 72269930Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled cold-reduced and plated or coated with zinc (excl. electrolytically plated or coated, and products of high-speed steel or silicon-electrical steel)0,142 1,706 (F)(1) 0,848 (G)(1) 0,493 (H)(1) 1,054 (J)(1) 1,532 (F)(2) 0,835 (G)(2) 0,480 (H)(2) 1,021 (J)(2) 72269970Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled cold-reduced and further worked (excl. plated or coated with zinc, and products of high-speed steel or silicon-electrical steel)0,142 1,706 (F)(1) 0,848 (G)(1) 0,493 (H)(1) 1,054 (J)(1) 1,532 (F)(2) 0,835 (G)(2) 0,480 (H)(2) 1,021 (J)(2) 72271000Bars and rods of high-speed steel, hot-rolled, in irregularly wound coils0,109 1,613 (F)(1) 0,788 (G)(1) 0,446 (H)(1) 0,986 (J)(1) 1,446 (F)(2) 0,775 (G)(2) 0,433 (H)(2) 0,954 (J)(2) 72272000Bars and rods of silico-manganese steel, hot-rolled, in irregularly wound coils0,109 1,613 (F)(1) 0,788 (G)(1) 0,446 (H)(1) 0,986 (J)(1) 1,446 (F)(2) 0,775 (G)(2) 0,433 (H)(2) 0,954 (J)(2) 72279010Bars and rods, hot-rolled, of steel containing by weight ≥ 0,0008 % of boron with any other element < the minimum content referred to in Note 1 f to this chapter, in irregularly wound coils0,109 1,435 (C) 0,546 (D) 0,137 (E) 72279050Bars and rods, hot-rolled, of steel containing by weight 0,9 % to 1,15 % carbon, 0,5 % to 2 % of chromium and, if present, ≤ 0,5 of molybdenum, in irregularly wound coils0,109 1,435 (C) 0,546 (D) 0,137 (E) 72279095Bars and rods, hot-rolled, in irregularly wound coils of alloy steel other than stainless (excl. of high-speed steel or silico-manganese steel and bars and rods of subheadings 72279010 and 72279050)0,109 1,613 (F)(1) 0,788 (G)(1) 0,446 (H)(1) 0,986 (J)(1) 1,446 (F)(2) 0,775 (G)(2) 0,433 (H)(2) 0,954 (J)(2) 72281020Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)0,109 1,613 (F)(1) 0,788 (G)(1) 0,446 (H)(1) 0,986 (J)(1) 1,446 (F)(2) 0,775 (G)(2)

0,433 (H)(2) 0,954 (J)(2) 72281050Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)0,303 1,807 (F)(1) 0,982 (G)(1) 0,640 (H)(1) 1,180 (J)(1) 1,640 (F)(2) 0,969 (G)(2) 0,628 (H)(2) 1,148 (J)(2) 72281090Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)0,109 1,613 (F)(1) 0,788 (G)(1) 0,446 (H)(1) 0,986 (J)(1) 1,446 (F)(2) 0,775 (G)(2) 0,433 (H)(2) 0,954 (J)(2) 72282010Bars and rods of silico-manganese steel, of rectangular other than square cross-section, hot-rolled on four faces (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)0,109 1,613 (F)(1) 0,788 (G)(1) 0,446 (H)(1) 0,986 (J)(1) 1,446 (F)(2) 0,775 (G)(2) 0,433 (H)(2) 0,954 (J)(2) 72282091Bars and rods of silico-manganese steel, of square or other than rectangular cross-section, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)0,109 1,613 (F)(1) 0,788 (G)(1) 0,446 (H)(1) 0,986 (J)(1) 1,446 (F)(2) 0,775 (G)(2) 0,433 (H)(2) 0,954 (J)(2) 72282099Bars and rods of silico-manganese stee, of square or other than rectangular cross-section, only cold-formed or cold-finished, incl. further worked, or hot-rolled and further worked (excl. hot-rolled, hot drawn or extruded, not further worked than clad, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)0,109 1,613 (F)(1) 0,788 (G)(1) 0,446 (H)(1) 0,986 (J)(1) 1,446 (F)(2) 0,775 (G)(2) 0,433 (H)(2) 0,954 (J)(2) 72283020Bars and rods of tool steel, only hot-rolled, only hot-drawn or only extruded (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)0,109 1,613 (F)(1) 0,788 (G)(1) 0,446 (H)(1) 0,986 (J)(1) 1,446 (F)(2) 0,775 (G)(2) 0,433 (H)(2) 0,954 (J)(2) 72283041Bars and rods of steel containing by weight 0,9 to 1,15 % of carbon and 0,5 to 2 % of chromium, and, if present, ≤ 0,5 % of molybdenum, only hot-rolled, hot-drawn or hot-extruded, of a circular cross-section of a diameter of ≥ 80 mm (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)0,109 1,435 (C) 0,546 (D) 0,137 (E) 72283049Bars and rods of steel containing by weight 0,9 to 1,15 % of carbon and 0,5 to 2 % of chromium, and, if present, ≤ 0,5 % of molybdenum, only hot-rolled, only hot-drawn or hot-extruded (other than of circular cross-section, of a diameter of ≥ 80 mm and excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)0,109

1,435 (C) 0,546 (D) 0,137 (E) 72283061Bars and rods of alloy steel other than stainless steel, only hot-rolled, hot-drawn or hot-extruded, of circular cross-section, of a diameter of ≥ 80 mm (other than of high-speed steel, silico-manganese steel, tool steel, articles of subheading 72283041 and excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)0,109 1,613 (F)(1) 0,788 (G)(1) 0,446 (H)(1) 0,986 (J)(1) 1,446 (F)(2) 0,775 (G)(2) 0,433 (H)(2) 0,954 (J)(2) 72283069Bars and rods or alloy steel other than stainless steel, only hot-rolled, hot-drawn or hot-extruded, of circular cross-section, of a diameter of < 80 mm (other than of high-speed steel, silico-manganese steel, tool steel and articles of subheading 72283049 and excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)0,109 1,613 (F)(1) 0,788 (G)(1) 0,446 (H)(1) 0,986 (J)(1) 1,446 (F)(2) 0,775 (G)(2) 0,433 (H)(2) 0,954 (J)(2) 72283070Bars and rods of alloy steel other than stainless steel, of rectangular other than square cross-section, hot-rolled on four faces (other than of high-speed steel, silico-manganese steel, tool steel, articles of subheading 72283041 and 72283049 and excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)0,109 1,613 (F)(1) 0,788 (G)(1) 0,446 (H)(1) 0,986 (J)(1) 1,446 (F)(2) 0,775 (G)(2) 0,433 (H)(2) 0,954 (J)(2) 72283089Bars and rods of alloy steel other than stainless steel, only hot-rolled, hot-drawn or hot-extruded, of other than rectangular [other than square] cross-section, rolled on four faces, or of circular cross-section (other than of high-speed steel, silico-manganese steel, tool steel, articles of subheading 72283049 and excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)0,109 1,613 (F)(1) 0,788 (G)(1) 0,446 (H)(1) 0,986 (J)(1) 1,446 (F)(2) 0,775 (G)(2) 0,433 (H)(2) 0,954 (J)(2) 72284010Bars and rods of tool steel, only forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)0,303 1,807 (F)(1) 0,982 (G)(1) 0,640 (H)(1) 1,180 (J)(1) 1,640 (F)(2) 0,969 (G)(2) 0,628 (H)(2) 1,148 (J)(2) 72284090Bars and rods of alloy steel, other than stainless steel, only forged (excl. of high-speed steel, silico-manganese steel, tool steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)0,303 1,807 (F)(1) 0,982 (G)(1) 0,640 (H)(1) 1,180 (J)(1) 1,640 (F)(2) 0,969 (G)(2) 0,628 (H)(2) 1,148 (J)(2) 72285020Bars and rods of tool steel, only cold-formed or cold-finished (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)0,109 1,613 (F)(1) 0,788 (G)(1) 0,446 (H)(1) 0,986 (J)(1) 1,446 (F)(2) 0,775 (G)(2) 0,433 (H)(2) 0,954 (J)(2) 72285040Bars and rods of steel containing 0,9 % to 1,15 % of carbon, 0,5 % to 2 % of chromium and, if present ≤ 0,5 % of molybdenum, only cold-formed or cold-finished (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)0,109

1,435 (C) 0,546 (D) 0,137 (E) 72285061Bars and rods of alloy steel, other than stainless steel, not further worked than cold-formed or cold-finished, of circular cross-section, of a diameter of ≥ 80 mm (excl. of high-speed steel, silico-manganese steel, tool steel, articles of subheading 72285040, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)0,109 1,613 (F)(1) 0,788 (G)(1) 0,446 (H)(1) 0,986 (J)(1) 1,446 (F)(2) 0,775 (G)(2) 0,433 (H)(2) 0,954 (J)(2) 72285069Bars and rods of alloy steel, other than stainless steel, not further worked than cold-formed or cold-finished, of circular cross-section, of a diameter of < 80 mm (excl. of high-speed steel, silico-manganese steel, tool steel, articles of subheading 72285040, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)0,109 1,613 (F)(1) 0,788 (G)(1) 0,446 (H)(1) 0,986 (J)(1) 1,446 (F)(2) 0,775 (G)(2) 0,433 (H)(2) 0,954 (J)(2) 72285080Bars and rods of alloy steel, other than stainless steel, not further worked than cold-formed or cold-finished (excl. of circular cross-section and products of high-speed steel, silico-manganese steel, tool steel, articles of subheading 72285040, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)0,109 1,613 (F)(1) 0,788 (G)(1) 0,446 (H)(1) 0,986 (J)(1) 1,446 (F)(2) 0,775 (G)(2) 0,433 (H)(2) 0,954 (J)(2) 72286020Bars and rods of tool steel, cold-formed or cold-finished and further worked or hot-formed and further worked (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)0,109 1,613 (F)(1) 0,788 (G)(1) 0,446 (H)(1) 0,986 (J)(1) 1,446 (F)(2) 0,775 (G)(2) 0,433 (H)(2) 0,954 (J)(2) 72286080Bars and rods of alloy steel, other than stainless steel, cold-formed or cold-finished and further worked or hot-formed and further worked (excl. bars and rods of high-speed steel, silico-manganese steel or tool steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)0,109 1,613 (F)(1) 0,788 (G)(1) 0,446 (H)(1) 0,986 (J)(1) 1,446 (F)(2) 0,775 (G)(2) 0,433 (H)(2) 0,954 (J)(2) 72287010Angles, shapes and sections of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded0,109 1,613 (F)(1) 0,788 (G)(1) 0,446 (H)(1) 0,986 (J)(1) 1,446 (F)(2) 0,775 (G)(2) 0,433 (H)(2) 0,954 (J)(2) 72287090Angles, shapes and sections of alloy steel other than stainless, n.e.s. (excl. products not further worked than hot-rolled, hot-drawn or extruded)0,109 1,613 (F)(1) 0,788 (G)(1) 0,446 (H)(1) 0,986 (J)(1) 1,446 (F)(2) 0,775 (G)(2) 0,433 (H)(2) 0,954 (J)(2) 72288000Hollow drill bars and rods, of alloy or non-alloy steel0,109 1,613 (F)(1) 0,788 (G)(1) 0,446 (H)(1) 0,986 (J)(1) 1,446 (F)(2) 0,775 (G)(2) 0,433 (H)(2) 0,954 (J)(2) 72292000Wire of silico-manganese steel, in coils (excl. bars and rods)0,109 1,613 (F)(1) 0,788 (G)(1)

0,446 (H)(1) 0,986 (J)(1) 1,446 (F)(2) 0,775 (G)(2) 0,433 (H)(2) 0,954 (J)(2) 72299020Wire of high-speed steel, in coils (excl. bars and rods)0,109 1,613 (F)(1) 0,788 (G)(1) 0,446 (H)(1) 0,986 (J)(1) 1,446 (F)(2) 0,775 (G)(2) 0,433 (H)(2) 0,954 (J)(2) 72299050Wire of steel containing by weight 0,9 % to 1,1 % of carbon, 0,5 % to 2 % of chromium and, if present, ≤ 0,5 % of molybdenum, in coils (excl. rolled bars and rods)0,109 1,435 (C) 0,546 (D) 0,137 (E) 72299090Wire of alloy steel other than stainless, in coils (excl. rolled bars and rods, wire of high-speed steel or silico-manganese steel and articles of subheading 72299050)0,109 1,613 (F)(1) 0,788 (G)(1) 0,446 (H)(1) 0,986 (J)(1) 1,446 (F)(2) 0,775 (G)(2) 0,433 (H)(2) 0,954 (J)(2) 73011000Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements0,079 1,458 (C) 0,533 (D) 0,108 (E) 73012000Angles, shapes and sections, of iron or steel, welded0,079 1,458 (C) 0,533 (D) 0,108 (E) 73021010Current-conducting rails of iron or steel, with parts of non-ferrous metal, for railway or tramway track (excl. check-rails)0,057 1,383 (C) 0,494 (D) 0,085 (E) 73021022Vignole rails of iron or steel, for railway or tramway track, new, of a weight of ≥ 36 kg/m0,057 1,383 (C) 0,494 (D) 0,085 (E) 73021028Vignole rails of iron or steel, for railway or tramway track, new, of a weight of < 36 kg/m0,057 1,383 (C) 0,494 (D) 0,085 (E) 73021040Grooved rails of iron or steel, for railway or tramway track, new0,057 1,383 (C) 0,494 (D) 0,085 (E) 73021050Rails of iron or steel, for railway or tramway track, new (excl. vignole rails, grooved rails, and current-conducting rails with parts of non-ferrous metal)0,057 1,383 (C) 0,494 (D) 0,085 (E) 73021090Rails of iron or steel, for railway or tramway track, used (excl. current-conducting rails with parts of non-ferrous metal)0,057 1,383 (C) 0,494 (D) 0,085 (E) 73023000Switch blades, crossing frogs, point rods and other crossing pieces, for railway or tramway track, of iron or steel0,057 1,383 (C) 0,494 (D) 0,085 (E) 73024000Fish-plates and sole plates of iron or steel, for railways or tramways0,057 1,383 (C) 0,494 (D) 0,085 (E) 73029000Sleepers cross-ties, check-rails, rack rails, chairs, chair wedges, rail clips, bedplates and ties and other specialised material for the jointing or fixing of railway or tramway track, of iron or steel (excl. rails, switch blades, crossing frogs, point rods and other crossing pieces, and fish-plates and sole plates)0,057 1,383 (C) 0,494 (D) 0,085 (E) 73030010Tubes and pipes of a kind used in pressure systems, of cast iron0,1631,48473030090Tubes, pipes and hollow profiles, of cast iron (excl. products of a kind used in pressure systems)0,1631,48473041100Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel0,057 1,173 (1) 1,135 (2) 73041910Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel, of an external diameter of ≤ 168,3 mm (excl. products of stainless steel or of cast iron)0,057

1,383 (C) 0,494 (D) 0,085 (E) 73041930Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel, of an external diameter of > 168,3 mm but ≤ 406,4 mm (excl. products of stainless steel or of cast iron)0,057 1,383 (C) 0,494 (D) 0,085 (E) 73041990Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel, of an external diameter of > 406,4 mm (excl. products of stainless steel or of cast iron)0,057 1,383 (C) 0,494 (D) 0,085 (E) 73042200Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas0,057 1,173 (1) 1,135 (2) 73042300Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron)0,057 1,383 (C) 0,494 (D) 0,085 (E) 73042400Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel0,057 1,173 (1) 1,135 (2) 73042910Casing and tubing of a kind used for drilling for oil or gas, seamless, of iron or steel, of an external diameter ≤ 168,3 mm (excl. products of cast iron)0,057 1,383 (C) 0,494 (D) 0,085 (E) 73042930Casing and tubing of a kind used for drilling for oil or gas, seamless, of iron or steel, of an external diameter > 168,3 mm, but ≤ 406,4 mm (excl. products of cast iron)0,057 1,383 (C) 0,494 (D) 0,085 (E) 73042990Casing and tubing of a kind used for drilling for oil or gas, seamless, of iron or steel, of an external diameter > 406,4 mm (excl. products of cast iron)0,057 1,383 (C) 0,494 (D) 0,085 (E) 73043120Precision tubes, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled cold-reduced (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas)0,057 1,383 (C) 0,494 (D) 0,085 (E) 73043180Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled cold-reduced (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas and precision tubes)0,057 1,383 (C) 0,494 (D) 0,085 (E) 73043950Threaded or threadable tubes gas pipe, seamless, of iron or non-alloy steel (excl. of cast iron)0,057 1,383 (C) 0,494 (D) 0,085 (E) 73043982Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, of an external diameter of ≤ 168,3 mm (excl. cold-drawn or cold-rolled, of cast iron, line pipe of a kind used for oil or gas pipelines, casing, tubing and drill pipe of a kind used in drilling for oil or gas and tubes, and gas pipes of subheading 73043950)0,057 1,383 (C) 0,494 (D) 0,085 (E) 73043983Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, of an external diameter of > 168,3 mm but ≤ 406,4 mm (excl. cold-drawn or cold-rolled, of cast iron, line pipe of a kind used for oil or gas pipelines, casing, tubing and drill pipe of a kind used in drilling for oil or gas and tubes, and gas pipes of subheading 73043950)0,057

1,383 (C) 0,494 (D) 0,085 (E) 73043988Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, of an external diameter of > 406,4 mm (excl. cold-drawn or cold-rolled, of cast iron, line pipe of a kind used for oil or gas pipelines, casing, tubing and drill pipe of a kind used in drilling for oil or gas and tubes, and gas pipes of subheading 73043950)0,057 1,383 (C) 0,494 (D) 0,085 (E) 73044100Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled cold-reduced (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas)0,057 1,173 (1) 1,135 (2) 73044983Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, of an external diameter of ≤ 168,3 mm (excl. cold-drawn or cold-rolled, line pipe of a kind used for oil or gas pipelines, and casing and tubing of a kind used for drilling for oil or gas and tubes)0,057 1,173 (1) 1,135 (2) 73044985Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, of an external diameter of > 168,3 mm but ≤ 406,4 mm (excl. cold-drawn or cold-rolled, line pipe of a kind used for oil or gas pipelines, and casing and tubing of a kind used for drilling for oil or gas and tubes)0,057 1,173 (1) 1,135 (2) 73044989Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, of an external diameter of > 406,4 mm (excl. cold-drawn or cold-rolled, line pipe of a kind used for oil or gas pipelines, and casing and tubing of a kind used for drilling for oil or gas and tubes)0,057 1,173 (1) 1,135 (2) 73045110Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled cold-reduced, straight and of uniform wall-thickness, containing by weight ≥ 0,9 % but ≤ 1,15 % carbon and ≥ 0,5 % but ≤ 2 % chromium, whether or not containing by weight ≤ 0,5 % molybdenum (excl. tubes, pipes and hollow profiles of subheadings 730419 to 730429)0,057 1,561 (F)(1) 0,736 (G)(1) 0,394 (H)(1) 0,934 (J)(1) 1,394 (F)(2) 0,723 (G)(2) 0,381 (H)(2) 0,902 (J)(2) 73045181Precision tubes, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled cold-reduced (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil and tubes, and pipes and hollow profiles, straight and of uniform wall-thickness, containing by weight ≥ 0,9 % but ≤ 1,15 % carbon and ≥ 0,5 % but ≤ 2 % chrome, whether or not containing by weight ≤ 0,5 % molybdenum)0,057 1,561 (F)(1) 0,736 (G)(1) 0,394 (H)(1) 0,934 (J)(1) 1,394 (F)(2) 0,723 (G)(2) 0,381 (H)(2) 0,902 (J)(2) 73045189Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled cold-reduced (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil, precision tubes, and , pipes and hollow profiles, straight and of uniform wall-thickness, containing by weight ≥ 0,9 % but ≤ 1,15 % carbon and ≥ 0,5 % but ≤ 2 % chrome, whether or not containing by weight ≤ 0,5 % molybdenum)0,057

1,561 (F)(1) 0,736 (G)(1) 0,394 (H)(1) 0,934 (J)(1) 1,394 (F)(2) 0,723 (G)(2) 0,381 (H)(2) 0,902 (J)(2) 73045930Tubes, pipes and hollow profiles of alloy steel (excl. stainless), seamless, of circular cross-section (not cold-drawn or cold-rolled), straight and of uniform wall-thickness, containing by weight ≥ 0,9 % but ≤ 1,15 % carbon and ≥ 0,5 % but ≤ 2 % chromium, whether or not containing by weight ≤ 0,5 % molybdenum (excl. tubes, pipes and hollow profiles of subheadings 730419 to 730429)0,057 1,383 (C) 0,494 (D) 0,085 (E) 73045982Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, of an external diameter of ≤ 168,3 mm (excl. cold-drawn or cold-rolled, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas, and products of subheading 73045930)0,057 1,561 (F)(1) 0,736 (G)(1) 0,394 (H)(1) 0,934 (J)(1) 1,394 (F)(2) 0,723 (G)(2) 0,381 (H)(2) 0,902 (J)(2) 73045983Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, of an external diameter of > 168,3 mm but ≤ 406,4 mm (excl. cold-drawn or cold-rolled, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas, and products of subheading 73045930)0,057 1,561 (F)(1) 0,736 (G)(1) 0,394 (H)(1) 0,934 (J)(1) 1,394 (F)(2) 0,723 (G)(2) 0,381 (H)(2) 0,902 (J)(2) 73045989Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, of an external diameter of > 406,4 mm (excl. cold-drawn or cold-rolled, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas, and products of subheading 73045930)0,057 1,561 (F)(1) 0,736 (G)(1) 0,394 (H)(1) 0,934 (J)(1) 1,394 (F)(2) 0,723 (G)(2) 0,381 (H)(2) 0,902 (J)(2) 73049000Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron)0,057 1,383 (C) 0,494 (D) 0,085 (E) 73051100Line pipe of a kind used for oil or gas pipelines, having circular cross-sections and an external diameter of > 406,4 mm, of iron or steel, longitudinally submerged arc welded0,079 1,458 (C) 0,533 (D) 0,108 (E) 73051200Line pipe of a kind used for oil or gas pipelines, having circular cross-sections and an external diameter of > 406,4 mm, of iron or steel, longitudinally arc welded (excl. products longitudinally submerged arc welded)0,079 1,458 (C) 0,533 (D) 0,108 (E) 73051900Line pipe of a kind used for oil or gas pipelines, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel (excl. products longitudinally arc welded)0,079 1,458 (C) 0,533 (D) 0,108 (E) 73052000Casing of a kind used in drilling for oil or gas, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel0,079 1,458 (C) 0,533 (D) 0,108 (E) 73053100Tubes and pipes having circular cross-sections and an external diameter of > 406,4 mm, of iron or steel, longitudinally welded (excl. products of a kind used for oil or gas pipelines or of a kind used in drilling for oil or gas)0,079

1,458 (C) 0,533 (D) 0,108 (E) 73053900Tubes and pipes having circular cross-sections and an external diameter of > 406,4 mm, of iron or steel, welded (excl. products longitudinally welded or of a kind used for oil or gas pipelines or of a kind used in drilling for oil or gas)0,079 1,458 (C) 0,533 (D) 0,108 (E) 73059000Tubes and pipes having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel, welded (excl. welded products or products of a kind used for oil or gas pipelines or of a kind used in drilling for oil or gas)0,079 1,458 (C) 0,533 (D) 0,108 (E) 73061100Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of ≤ 406,4 mm0,109 1,270 (1) 1,230 (2) 73061900Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of ≤ 406,4 mm (excl. products of stainless steel or of cast iron)0,079 1,458 (C) 0,533 (D) 0,108 (E) 73062100Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of ≤ 406,4 mm0,109 1,270 (1) 1,230 (2) 73062900Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of ≤ 406,4 mm (excl. products of stainless steel or of cast iron)0,079 1,458 (C) 0,533 (D) 0,108 (E) 73063012Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled cold-reduced0,079 1,458 (C) 0,533 (D) 0,108 (E) 73063018Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled)0,044 1,370 (C) 0,481 (D) 0,072 (E) 73063041Threaded or threadable tubes gas pipe, welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc0,112 1,491 (C) 0,567 (D) 0,141 (E) 73063049Threaded or threadable tubes gas pipe, welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc)0,112 1,491 (C) 0,567 (D) 0,141 (E) 73063072Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of ≤ 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas)0,112 1,491 (C) 0,567 (D) 0,141 (E) 73063077Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of ≤ 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes gas pipe)0,112 1,491 (C) 0,567 (D) 0,141 (E) 73063080Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but ≤ 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes gas pipe)0,112

1,491 (C) 0,567 (D) 0,141 (E) 73064020Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled cold-reduced (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas)0,109 1,270 (1) 1,230 (2) 73064080Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled cold-reduced, tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas)0,073 1,189 (1) 1,151 (2) 73065021Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled cold-reduced0,109 1,673 (F)(1) 0,815 (G)(1) 0,460 (H)(1) 1,021 (J)(1) 1,499 (F)(2) 0,801 (G)(2) 0,446 (H)(2) 0,987 (J)(2) 73065029Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled)0,073 1,577 (F)(1) 0,752 (G)(1) 0,410 (H)(1) 0,950 (J)(1) 1,409 (F)(2) 0,739 (G)(2) 0,397 (H)(2) 0,918 (J)(2) 73065080Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes)0,109 1,673 (F)(1) 0,815 (G)(1) 0,460 (H)(1) 1,021 (J)(1) 1,499 (F)(2) 0,801 (G)(2) 0,446 (H)(2) 0,987 (J)(2) 73066110Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel0,109 1,270 (1) 1,230 (2) 73066192Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of ≤ 2 mm0,112 1,491 (C) 0,567 (D) 0,141 (E) 73066199Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm0,112 1,491 (C) 0,567 (D) 0,141 (E) 73066910Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section)0,109 1,270 (1) 1,230 (2) 73066990Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section)0,112

1,491 (C) 0,567 (D) 0,141 (E) 73069000Tubes, pipes and hollow profiles e.g., open seam, riveted or similarly closed, of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm)0,112 1,491 (C) 0,567 (D) 0,141 (E) 73071110Tube or pipe fittings of non-malleable cast iron, of a kind used in pressure systems0,1631,40973071190Tube or pipe fittings of non-malleable cast iron (excl. products of a kind used in pressure systems)0,1631,40973071910Tube or pipe fittings of cast iron (excl. of non-malleable)0,1631,40973071990Cast tube or pipe fittings of steel0,303 1,629 (C) 0,740 (D) 0,331 (E) 73072100Flanges of stainless steel (excl. cast products)0,057 1,173 (1) 1,135 (2) 73072210Sleeves, of stainless steel, threaded (excl. cast products)0,057 1,173 (1) 1,135 (2) 73072290Elbows and bends, of stainless steel, threaded (excl. cast products)0,057 1,173 (1) 1,135 (2) 73072310Butt welding elbows and bends of stainless steel (excl. cast products)0,057 1,173 (1) 1,135 (2) 73072390Butt welding tube or pipe fittings of stainless steel (excl. cast products and elbows and bends)0,057 1,173 (1) 1,135 (2) 73072910Threaded tube or pipe fittings of stainless steel (excl. cast products, flanges, elbows, bends and sleeves)0,057 1,173 (1) 1,135 (2) 73072980Tube or pipe fittings of stainless steel (excl. cast, threaded, butt welding fittings and flanges)0,057 1,173 (1) 1,135 (2) 73079100Flanges of iron or steel (excl. cast or stainless products)0,057 1,383 (C) 0,494 (D) 0,085 (E) 73079210Sleeves of iron or steel, threaded (excl. cast or of stainless steel)0,057 1,383 (C) 0,494 (D) 0,085 (E) 73079290Elbows and bends, of iron or steel, threaded (excl. cast or of stainless steel)0,057 1,383 (C) 0,494 (D) 0,085 (E) 73079311Butt welding elbows and bends, of iron or steel, with greatest external diameter ≤ 609,6 mm (excl. cast iron or stainless steel products)0,057 1,383 (C) 0,494 (D) 0,085 (E) 73079319Butt welding fittings of iron or steel, with greatest external diameter ≤ 609,6 mm (excl. cast iron or stainless steel products, elbows, bends and flanges)0,057 1,383 (C) 0,494 (D) 0,085 (E) 73079391Butt welding elbows and bends, of iron or steel, with greatest external diameter > 609,6 mm (excl. cast iron or stainless steel products)0,057 1,383 (C) 0,494 (D) 0,085 (E) 73079399Butt welding fittings of iron or steel, with greatest external diameter > 609,6 mm (excl. cast iron or stainless steel products, elbows, bends and flanges)0,057 1,383 (C) 0,494 (D) 0,085 (E) 73079910Threaded tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products, flanges, elbows, bends and sleeves)0,057 1,383 (C) 0,494 (D) 0,085 (E) 73079980Tube or pipe fittings, of iron or steel (excl. of cast iron or stainless steel, threaded, butt welding fittings, and flanges)0,057 1,383 (C) 0,494 (D) 0,085 (E) 73081000Bridges and bridge-sections, of iron or steel0,112 1,491 (C)

0,567 (D) 0,141 (E) 73082000Towers and lattice masts, of iron or steel0,112 1,491 (C) 0,567 (D) 0,141 (E) 73083000Doors, windows and their frames and thresholds for doors, of iron or steel0,112 1,491 (C) 0,567 (D) 0,141 (E) 73084000Equipment for scaffolding, shuttering, propping or pit-propping (excl. composite sheetpiling products and formwork panels for poured-in-place concrete, which have the characteristics of moulds)0,112 1,491 (C) 0,567 (D) 0,141 (E) 73089051Panels comprising two walls of profiled ribbed sheet, of iron or steel, with an insulating core0,112 1,491 (C) 0,567 (D) 0,141 (E) 73089059Structures and parts of structures, of iron or steel, solely or principally of sheet, n.e.s. (excl. doors and windows and their frames, and panels comprising two walls of profiled ribbed sheet, of iron or steel, with an insulating core)0,112 1,491 (C) 0,567 (D) 0,141 (E) 73089098Structures and parts of structures of iron or steel, n.e.s. (excl. bridges and bridge-sections; towers; lattice masts; doors, windows and their frames and thresholds; equipment for scaffolding, shuttering, propping or pit-propping, and products made principally of sheet)0,112 1,491 (C) 0,567 (D) 0,141 (E) 73090010Reservoirs, tanks, vats and similar containers, of iron or steel, for gases other than compressed or liquefied gas, of a capacity of > 300 l (excl. containers fitted with mechanical or thermal equipment and containers specifically constructed or equipped for one or more types of transport)0,112 1,491 (C) 0,567 (D) 0,141 (E) 73090030Reservoirs, tanks, vats and similar containers, of iron or steel, for liquids, lined or heat-insulated and of a capacity of > 300 l (excl. containers fitted with mechanical or thermal equipment and containers specifically constructed or equipped for one or more types of transport)0,112 1,491 (C) 0,567 (D) 0,141 (E) 73090051Reservoirs, tanks, vats and similar containers, of iron or steel, for liquids, of a capacity of > 100.000 l (excl. containers lined or heat-insulated or fitted with mechanical or thermal equipment and containers specifically constructed or equipped for one or more types of transport)0,112 1,491 (C) 0,567 (D) 0,141 (E) 73090059Reservoirs, tanks, vats and similar containers, of iron or steel, for liquids, of a capacity of ≤ 100.000 l but > 300 l (excl. containers lined or heat-insulated or fitted with mechanical or thermal equipment and containers specifically constructed or equipped for one or more types of transport)0,112 1,491 (C) 0,567 (D) 0,141 (E) 73090090Reservoirs, tanks, vats and similar containers, of iron or steel, for solids, of a capacity of > 300 l (excl. containers lined or heat-insulated or fitted with mechanical or thermal equipment and containers specifically constructed or equipped for one or more types of transport)0,112 1,491 (C) 0,567 (D) 0,141 (E) 73101000Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material, of a capacity of ≥ 50 l but ≤ 300 l, n.e.s. (excl. containers for compressed or liquefied gas, or containers fitted with mechanical or thermal equipment)0,112

1,491 (C) 0,567 (D) 0,141 (E) 73102111Cans of iron or steel, of a capacity of < 50 l, which are to be closed by soldering or crimping, of a kind used for preserving food0,112 1,491 (C) 0,567 (D) 0,141 (E) 73102119Cans of iron or steel, of a capacity of < 50 l, which are to be closed by soldering or crimping, of a kind used for preserving drink0,112 1,491 (C) 0,567 (D) 0,141 (E) 73102191Cans of iron or steel, of a capacity of < 50 l, which are to be closed by soldering or crimping, of a wall thickness of < 0,5 mm (excl. cans for compressed or liquefied gas, and cans of a kind used for preserving food and drink)0,112 1,491 (C) 0,567 (D) 0,141 (E) 73102199Cans of iron or steel, of a capacity of < 50 l, which are to be closed by soldering or crimping, of a wall thickness of ≥ 0,5 mm (excl. cans for compressed or liquefied gas, and cans of a kind used for preserving food and drink)0,112 1,491 (C) 0,567 (D) 0,141 (E) 73102910Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material, of a capacity of < 50 l and of a wall thickness of < 0,5 mm, n.e.s. (excl. containers for compressed or liquefied gas, or containers fitted with mechanical or thermal equipment, and cans which are to be closed by soldering or crimping)0,112 1,491 (C) 0,567 (D) 0,141 (E) 73102990Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material, of a capacity of < 50 l and of a wall thickness of ≥ 0,5 mm, n.e.s. (excl. containers for compressed or liquefied gas, or containers fitted with mechanical or thermal equipment, and cans which are to be closed by soldering or crimping)0,112 1,491 (C) 0,567 (D) 0,141 (E) 73110011Containers of iron or steel, seamless, for compressed or liquefied gas, for a pressure ≥ 165 bar, of a capacity < 20 l (excl. containers specifically constructed or equipped for one or more types of transport)0,038 1,364 (C) 0,475 (D) 0,066 (E) 73110013Containers of iron or steel, seamless, for compressed or liquefied gas, for a pressure ≥ 165 bar, of a capacity ≥ 20 l to ≤ 50 l (excl. containers specifically constructed or equipped for one or more types of transport)0,038 1,364 (C) 0,475 (D) 0,066 (E) 73110019Containers of iron or steel, seamless, for compressed or liquefied gas, for a pressure ≥ 165 bar, of a capacity > 50 l (excl. containers specifically constructed or equipped for one or more types of transport)0,038 1,364 (C) 0,475 (D) 0,066 (E) 73110030Containers of iron or steel, seamless, for compressed or liquefied gas, for a pressure < 165 bar (excl. containers specifically constructed or equipped for one or more types of transport)0,038 1,364 (C) 0,475 (D) 0,066 (E) 73110091Containers of iron or steel, seamless, for compressed or liquefied gas, of a capacity of < 1.000 l (excl. seamless containers and containers specifically constructed or equipped for one or more types of transport)0,038 1,364 (C) 0,475 (D) 0,066 (E) 73110099Containers of iron or steel, seamless, for compressed or liquefied gas, of a capacity of ≥ 1.000 l (excl. seamless containers and containers specifically constructed or equipped for one or more types of transport)0,038

1,364 (C) 0,475 (D) 0,066 (E) 73181100Coach screws of iron or steel0,038 1,364 (C) 0,475 (D) 0,066 (E) 73181210Wood screws of stainless steel (excl. coach screws)0,038 1,154 (1) 1,116 (2) 73181290Wood screws of iron or steel other than stainless (excl. coach screws)0,038 1,364 (C) 0,475 (D) 0,066 (E) 73181300Screw hooks and screw rings, of iron or steel0,038 1,364 (C) 0,475 (D) 0,066 (E) 73181410Self-tapping screws, of stainless steel (excl. wood screws)0,038 1,154 (1) 1,116 (2) 73181491Spaced-thread screws of iron or steel other than stainless0,038 1,364 (C) 0,475 (D) 0,066 (E) 73181499Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws)0,038 1,364 (C) 0,475 (D) 0,066 (E) 73181520Screws and bolts, of iron or steel whether or not with their nuts and washers, for fixing railway track construction material (excl. coach screws)0,038 1,364 (C) 0,475 (D) 0,066 (E) 73181535Screws and bolts, of stainless steel whether or not with their nuts and washers, without heads (excl. screws and bolts for fixing railway track construction material)0,038 1,154 (1) 1,116 (2) 73181542Screws and bolts, of iron or steel other than stainless whether or not with their nuts and washers, without heads, with a tensile strength of < 800 MPa (excl. screws and bolts for fixing railway track construction material)0,038 1,364 (C) 0,475 (D) 0,066 (E) 73181548Screws and bolts, of iron or steel other than stainless whether or not with their nuts and washers, without heads, with a tensile strength of ≥ 800 MPa (excl. screws and bolts for fixing railway track construction material)0,038 1,364 (C) 0,475 (D) 0,066 (E) 73181552Screws and bolts, of stainless steel whether or not with their nuts and washers, with slotted or cross-recessed heads (excl. wood screws and self-tapping screws)0,038 1,154 (1) 1,116 (2) 73181558Screws and bolts, of iron or steel other than stainless whether or not with their nuts and washers, with slotted or cross-recessed heads (excl. wood screws and self-tapping screws)0,038 1,364 (C) 0,475 (D) 0,066 (E) 73181562Hexagonal-socket head screws and bolts, of stainless steel whether or not with their nuts and washers (excl. wood screws, self-tapping screws and screws and bolts for fixing railway track construction material)0,038 1,154 (1) 1,116 (2) 73181568Hexagonal-socket head screws and bolts, of iron or steel other than stainless whether or not with their nuts and washers (excl. wood screws, self-tapping screws and screws and bolts for fixing railway track construction material)0,038 1,364 (C) 0,475 (D) 0,066 (E) 73181575Hexagon screws and bolts, of stainless steel whether or not with their nuts and washers (excl. with socket head, wood screws, self-tapping screws and screws and bolts for fixing railway track construction material)0,038 1,154 (1) 1,116 (2) 73181582Hexagon screws and bolts, of iron or steel other than stainless whether or not with their nuts and washers, with a tensile strength of < 800 MPa (excl. with socket head, wood screws, self-tapping screws and screws and bolts for fixing railway track construction material)0,038

1,364 (C) 0,475 (D) 0,066 (E) 73181588Hexagon screws and bolts, of iron or steel other than stainless whether or not with their nuts and washers, with a tensile strength of ≥ 800 MPa (excl. with socket head, wood screws, self-tapping screws and screws and bolts for fixing railway track construction material)0,038 1,364 (C) 0,475 (D) 0,066 (E) 73181595Screws and bolts, of iron or steel whether or not with their nuts and washers, with heads (excl. with slotted, cross-recessed or hexagonal head; wood screws, self-tapping screws and screws and bolts for fixing railway track construction material, screw hooks and screw rings)0,038 1,364 (C) 0,475 (D) 0,066 (E) 73181631Blind rivet nuts of stainless steel0,038 1,154 (1) 1,116 (2) 73181639Nuts of stainless steel (excl. blind rivet nuts)0,038 1,154 (1) 1,116 (2) 73181640Blind rivet nuts of iron or steel other than stainless0,038 1,364 (C) 0,475 (D) 0,066 (E) 73181660Self-locking nuts of iron or steel other than stainless0,038 1,364 (C) 0,475 (D) 0,066 (E) 73181692Nuts of iron or steel other than stainless, with an inside diameter ≤ 12 mm (excl. blind rivet nuts and self-locking nuts)0,038 1,364 (C) 0,475 (D) 0,066 (E) 73181699Nuts of iron or steel other than stainless, with an inside diameter > 12 mm (excl. blind rivet nuts and self-locking nuts)0,038 1,364 (C) 0,475 (D) 0,066 (E) 73181900Threaded articles, of iron or steel, n.e.s.0,038 1,364 (C) 0,475 (D) 0,066 (E) 73182100Spring washers and other lock washers, of iron or steel0,038 1,364 (C) 0,475 (D) 0,066 (E) 73182200Washers of iron or steel (excl. spring washers and other lock washers)0,038 1,364 (C) 0,475 (D) 0,066 (E) 73182300Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses)0,038 1,364 (C) 0,475 (D) 0,066 (E) 73182400Cotters and cotter pins, of iron or steel0,038 1,364 (C) 0,475 (D) 0,066 (E) 73182900Non-threaded articles, of iron or steel0,038 1,364 (C) 0,475 (D) 0,066 (E) 73261100Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked0,303 1,629 (C) 0,740 (D) 0,331 (E) 73261910Articles of iron or steel, open-die forged, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills)0,303 1,629 (C) 0,740 (D) 0,331 (E) 73261990Articles of iron or steel, closed-die forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills)0,303 1,629 (C) 0,740 (D) 0,331 (E) 73262000Articles of iron or steel wire, n.e.s.0,071 1,397 (C) 0,508 (D) 0,099 (E) 73269030Ladders and steps, of iron or steel0,038 1,364 (C) 0,475 (D) 0,066 (E) 73269040Pallets and similar platforms for handling goods, of iron or steel0,038 1,364 (C) 0,475 (D) 0,066 (E) 73269050Reels for cables, piping and the like, of iron or steel0,038 1,364 (C) 0,475 (D) 0,066 (E) 73269060Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel0,038 1,364 (C) 0,475 (D) 0,066 (E) 73269092Articles of iron or steel, open-die forged, n.e.s.0,303

1,629 (C) 0,740 (D) 0,331 (E) 73269094Articles of iron or steel, closed-die forged, n.e.s.0,303 1,629 (C) 0,740 (D) 0,331 (E) 73269096Sintered articles of iron or steel, n.e.s.0,303 1,629 (C) 0,740 (D) 0,331 (E) 73269098Articles of iron or steel, n.e.s.0,112 1,491 (C) 0,567 (D) 0,141 (E) Aluminium76011010Aluminium slabs, not alloyed, unwrought 1,423 (K) 0,091 (L) 1,423 (K) 0,091 (L) 76011090Aluminium, not alloyed, unwrought (excl. slabs) 1,423 (K) 0,091 (L) 1,423 (K) 0,091 (L) 76012030Unwrought aluminium alloys in the form of slabs 1,423 (K) 0,091 (L) 1,423 (K) 0,091 (L) 76012040Unwrought aluminium alloys in the form of billets 1,423 (K) 0,091 (L) 1,423 (K) 0,091 (L) 76012080Unwrought aluminium alloys (excl. slabs and billets) 1,423 (K) 0,091 (L) 1,423 (K) 0,091 (L) 76031000Powders of aluminium, of non-lamellar structure (excl. pellets of aluminium)0,046 1,506 (K) 0,140 (L) 76032000Powders of aluminium, of lamellar structure, and flakes of aluminium (excl. pellets of aluminium, and spangles)0,046 1,506 (K) 0,140 (L) 76041010Bars, rods and profiles, of non-alloy aluminium0,056 1,485 (K) 0,148 (L) 76041090Profiles of non-alloy aluminium, n.e.s.0,060 1,493 (K) 0,152 (L) 76042100Hollow profiles of aluminium alloys, n.e.s.0,060 1,493 (K) 0,152 (L) 76042910Bars and rods of aluminium alloys0,056 1,485 (K) 0,148 (L) 76042990Solid profiles, of aluminium alloys, n.e.s.0,060 1,493 (K) 0,152 (L) 76051100Wire of non-alloy aluminium, with a maximum cross-sectional dimension of > 7 mm (excl. stranded wire, cables, plaited bands and the like and other articles of heading 7614, and electrically insulated wires)0,056 1,485 (K) 0,148 (L) 76051900Wire of non-alloy aluminium, with a maximum cross-sectional dimension of ≤ 7 mm (other than stranded wires, cables, ropes and other articles of heading 7614, electrically insulated wires, strings for musical instruments)0,056 1,485 (K) 0,148 (L) 76052100Wire of aluminium alloys, with a maximum cross-sectional dimension of > 7 mm (excl. stranded wire, cables, plaited bands and the like and other articles of heading 7614, and electrically insulated wires)0,056 1,485 (K) 0,148 (L) 76052900Wire, of aluminium alloys, having a maximum cross-sectional dimension of ≤ 7 mm (other than stranded wires, cables, ropes and other articles of heading 7614, electrically insulated wires, strings for musical instruments)0,056 1,485 (K) 0,148 (L) 76061130Aluminium Composite Panel, of non-alloy aluminium, of a thickness of > 0,2 mm0,056 1,485 (K) 0,148 (L) 76061150Plates, sheets and strip, of non-alloy aluminium, of a thickness of > 0,2 mm, square or rectangular, painted, varnished or coated with plastics (excl. Aluminium Composite Panel)0,056 1,485 (K) 0,148 (L) 76061191Plates, sheets and strip, of non-alloy aluminium, of a thickness of > 0,2 mm but < 3 mm, square or rectangular (excl. such products painted, varnished or coated with plastics, and expanded plates, sheets and strip)0,056 1,485 (K) 0,148 (L) 76061193Plates, sheets and strip, of non-alloy aluminium, of a thickness of ≥ 3 mm but < 6 mm, square or rectangular (excl. such products painted, varnished or coated with plastics)0,056

1,485 (K) 0,148 (L) 76061199Plates, sheets and strip, of non-alloy aluminium, of a thickness of ≥ 6 mm, square or rectangular (excl. such products painted, varnished or coated with plastics)0,056 1,485 (K) 0,148 (L) 76061211Beverage can body stock, of aluminium alloys, of a thickness of > 0,2 mm0,056 1,485 (K) 0,148 (L) 76061219Beverage can end stock and tab stock, of aluminium alloys, of a thickness of > 0,2 mm0,056 1,485 (K) 0,148 (L) 76061230Aluminium Composite Panel, of aluminium alloys, of a thickness of > 0,2 mm0,056 1,485 (K) 0,148 (L) 76061250Plates, sheets and strip, of aluminium alloys, of a thickness of > 0,2 mm, square or rectangular, painted, varnished or coated with plastics (excl. beverage can body stock, end stock and tab stock, and Aluminium Composite Panel)0,056 1,485 (K) 0,148 (L) 76061292Plates, sheets and strip, of aluminium alloys, of a thickness of > 0,2 mm but < 3 mm, square or rectangular (excl. painted, varnished or coated with plastics, expanded plates, sheets and strip, beverage can body stock, end stock and tab stock)0,056 1,485 (K) 0,148 (L) 76061293Plates, sheets and strip, of aluminium alloys, of a thickness of ≥ 3 mm but < 6 mm, square or rectangular (excl. such products painted, varnished or coated with plastics)0,056 1,485 (K) 0,148 (L) 76061299Plates, sheets and strip, of aluminium alloys, of a thickness of ≥ 6 mm, square or rectangular (excl. such products painted, varnished or coated with plastics)0,056 1,485 (K) 0,148 (L) 76069100Plates, sheets and strip, of non-alloy aluminium, of a thickness of > 0,2 mm (other than square or rectangular)0,056 1,485 (K) 0,148 (L) 76069200Plates, sheets and strip, of aluminium alloys, of a thickness of > 0,2 mm (other than square or rectangular)0,056 1,485 (K) 0,148 (L) 76071111Aluminium foil, not backed, rolled but not further worked, of a thickness of < 0,021 mm, in rolls of a weight of ≤ 10 kg (excl. stamping foils of heading 3212, and foil made up as christmas tree decorating material)0,166 1,599 (K) 0,258 (L) 76071119Aluminium foil, not backed, rolled but not further worked, of a thickness of < 0,021 mm (excl. stamping foils of heading 3212, and foil made up as christmas tree decorating material and in rolls of a weight ≤ 10 kg)0,166 1,599 (K) 0,258 (L) 76071190Aluminium foil, not backed, rolled but not further worked, of a thickness of ≥ 0,021 mm but ≤ 2 mm (excl. stamping foils of heading 3212, and foil made up as christmas tree decorating material)0,166 1,599 (K) 0,258 (L) 76071910Aluminium foil, not backed, rolled and further worked, of a thickness of < 0,021 mm (excl. stamping foils of heading 3212, and foil made up as christmas tree decorating material)0,166 1,599 (K) 0,258 (L) 76071990Aluminium foil, not backed, rolled and further worked, of a thickness (excl. any backing) from 0,021 mm to 0,2 mm (excl. stamping foils of heading 3212, and foil made up as christmas tree decorating material)0,166 1,599 (K) 0,258 (L) 76072010Aluminium foil, backed, of a thickness (excl. any backing) of < 0,021 mm (excl. stamping foils of heading 3212, and foil made up as christmas tree decorating material)0,166

1,599 (K) 0,258 (L) 76072091Aluminium Composite Panel, of a thickness ≤ 0,2 mm0,166 1,599 (K) 0,258 (L) 76072099Aluminium foil, backed, of a thickness (excl. any backing) of ≥ 0,021 mm but ≤ 0,2 mm (excl. stamping foils of heading 3212, foil made up as christmas tree decorating material, and Aluminium Composite Panel)0,166 1,599 (K) 0,258 (L) 76081000Tubes and pipes of non-alloy aluminium (excl. hollow profiles)0,060 1,493 (K) 0,152 (L) 76082020Tubes and pipes of aluminium alloys, welded (excl. hollow profiles)0,060 1,493 (K) 0,152 (L) 76082081Tubes and pipes of aluminium alloys, not further worked than extruded (excl. hollow profiles)0,060 1,493 (K) 0,152 (L) 76082089Tubes and pipes of aluminium alloys (excl. such products welded or not further worked than extruded, and hollow profiles)0,060 1,493 (K) 0,152 (L) 76090000Aluminium tube or pipe fittings e.g., couplings, elbows, sleeves0,060 1,493 (K) 0,152 (L) 76101000Doors, windows and their frames and thresholds for door, of aluminium (excl. door furniture)0,060 1,493 (K) 0,152 (L) 76109010Bridges and bridge-sections, towers and lattice masts, of aluminium0,060 1,493 (K) 0,152 (L) 76109090Structures and parts of structures, of aluminium, n.e.s., and plates, rods, profiles, tubes and the like, prepared for use in structures, of aluminium, n.e.s. (excl. prefabricated buildings of heading 9406, doors and windows and their frames and thresholds for doors, bridges and bridge-sections, towers and lattice masts)0,060 1,493 (K) 0,152 (L) 76110000Reservoirs, tanks, vats and similar containers, of aluminium, for any material (other than compressed or liquefied gas), of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport)0,166 1,594 (K) 0,258 (L) 76121000Collapsible tubular containers, of aluminium0,166 1,594 (K) 0,258 (L) 76129020Containers of a kind used for aerosols, of aluminium0,166 1,594 (K) 0,258 (L) 76129030Casks, drums, cans, boxes and similar containers, of aluminium, manufactured from foil of a thickness ≤ 0,2 mm0,166 1,594 (K) 0,258 (L) 76129080Casks, drums, cans, boxes and similar containers ≤ 300 l, of aluminium, for any material (other than compressed or liquefied gas), n.e.s. (other than collapsible tubular containers, containers for aerosols and containers manufactured from foil of a thickness ≤ 0,2 mm0,166 1,594 (K) 0,258 (L) 76130000Aluminium containers for compressed or liquefied gas0,166 1,594 (K) 0,258 (L) 76141000Stranded wire, cables, plaited bands and the like, of aluminium, with steel core (excl. such products electrically insulated)0,056 1,485 (K) 0,148 (L) 76149000Stranded wires, cables, ropes and similar articles, of aluminium (other than with steel core and electrically insulated products)0,056 1,485 (K) 0,148 (L) 76161000Nails, tacks, staples, screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles, of aluminium (excl. staples in strips, plugs, bungs and the like, threaded)0,056

1,485 (K) 0,148 (L) 76169100Cloth, grill, netting and fencing, of aluminium wire (excl. cloth of metal fibres for clothing, lining and similar uses, and cloth, grill and netting made into hand sieves or machine parts)0,056 1,485 (K) 0,148 (L) 76169910Articles of aluminium, cast, n.e.s.0,046 1,506 (K) 0,140 (L) 76169990Articles of aluminium, uncast, n.e.s.0,056 1,485 (K) 0,148 (L)